adreno Posted October 18, 2005 Posted October 18, 2005 DFI LANPARTY nF3 Ultra-D - 7/11/2005 BIOS AMD Athlon64 3000+ S939 (Venice), (LBBLE0522CPMW) Corsair PC3200 4x512MB ,(VS1GBKIT400) ATI Radeon 9800 Pro 128MB, Catalyst (5.8) MAXTOR 80GB (6Y080L0) IDE hdd (8MB cache) LG GCR-8523B 52X MAX EIDE Enermax EG495P-VE Noisetaker 485W Power Supply Zalman CNPS7000B-CU AS5 ========== Genie BIOS Settings: CPU Overclock in MHz = 290 Hammer Fid Control = x9 AGP OverClock in MHz = 67 LDT/FSB Frequency Ratio = 3x AMD K8 Cool and Quiet = Disable CPU VID Control = 1.525v CPU Voltage adjusting = +0.3v Chipset Voltage Control = 1.75v Memory Voltage Control = 2.7v AGP Voltage Control = 1.6v DRAM Configuration Settings: Memory Hole for PCI MMIO = Disabled Max Memclock (MHz) = Auto 1T/2T Memory Timing = 2T CAS# latency (Tcl) = 2.5 RAS# to CAS# delay (Trcd) = 3 Min RAS# active time (Tras) = 7 Row precharge Time (Trp) = 3 Write Recovery Time (Twr) = Auto RAS#-to-RAS# delay (Trrd) = 3 Row Refresh time (Trfc) = 13 Row cycle time (Trc) = 11 Write-to-Read Delay Twtr) = 2 Read-to-Write Delay (Trwt) = 2 Refresh Rate (Tref) = Auto Write Cas Latency (Twcl) = 1 Max Asynchronous latency = 8ns Read Preamble = 6.0ns Dynamic Idle Cycle counter = 256 DDR output driving = Weak Drive DDR DQ drive strength = 50% Reduction ECC Function = Disable ========== Prime95 + 3dMark2001SE + CPU-Z 1.3 + Everest 2.20.405: 3dMark2003: (6304) 3dMark2005: (2851) Aquamark 3d: (52,012) ========== short description: 9x290 @ 2630Mhz 1.57V +0.3 2.5,3,3,7 2T LDT3x @2.7v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted October 20, 2005 Posted October 20, 2005 DFI LANPARTY nF4 SLI-DR - 7/04-2 BigToe BIOS AMD Athlon64 X2 4400+ dual core 4x1024 OCZ PC4000EL Gold (OCZ5002048ELGE-K) XFX 7800GTX 256MB, 496/1319 81.82 drivers 3x Western Digital "Raptor" 10,000RPM SATA (RAID-0) ASUS CD-S520/A5 Black IDE CD-ROM Drive OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 245 LDT/FSB Frequency Ratio....................... - AUTO CPU/FSB Frequency Ratio....................... - Auto PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.350v CPU VID Special Control....................... - Above VID * 113% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - [b]2.80v[/b][/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Disable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 04 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 04 Bus Clocks Row Cycle time (Trc).......................... - 13 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/nf4/4...x2_245x11-1.jpg 3dMark2003: 3dMark2005: Aquamark 3d: AMD Nbench: ========== short description: 245x11 @ 2696Mhz, 1.350v + 113% 3.0-4-8-4 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted October 21, 2005 Posted October 21, 2005 DFI nF4 DAGF - 08/11/2005 BIOS 4000 Sandy CABGE 0515SPWM 2x1024mb Patriot LL Power Color x850xt @ 580621 with Cat 5.9 1x 20gig Western Digital IDE drive ASUS IDE CD-ROM Drive OCZ 600w Power Stream SLI Edition Thermalright SLK948U with 92mm Panaflo * * * * ========== Genie BIOS Settings: CPU Frequency - 250 Hammer Fid Control - 11 HTT Frequency - 4 PCIE Clock - 100Mhz DDR Voltage Control - 2.8v Chip Voltage Control - 1.6v CPU Voltage - 1.625 DRAM Configuration Settings: Mem Clock mode - Limit Mem Clock Index Value - 200 (DRAM/FSB:1/01) CAS Latency Control (Tcl) - 2.5 Min RAS# active time (Tras) - 05 Bus Clocks RAS# to CAS# delay (Trcd) - 03 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DDR Output Driving - Weak DDR DQ Drive Strenth - Auto Bottom of 32Bit[31:24]IO - B0 1T2T Memory Timing - 1T Read Preamble Value - 5.5ns Async Latency Value - 8ns Dynamic IdleCycle Counter - Auto DRAM Bank Interleave - Enable Burst Length - 4 beats Enable ALL DIMM Clock - enable SW Memory hole remapping - disable HW Memory hole remapping - disable MTRR Mapping mode - continuous DRAM ECC Feature Control - disable ========== Prime95 + 3dMark2001SE + 2xCPU-Z : 3dMark2003 + Everest : 3dMark2005 : Aquamark 3d: ========== short description: 250x11=2750mhz 1.625vcore 2.8vdimm Share this post Link to post Share on other sites More sharing options...
OatMan Posted October 22, 2005 Posted October 22, 2005 DFI LANPARTY nF4 Ultra-D - 6/23BIOS (shipping BIOS) AMD Athlon64 3200+ E6 Venice ADA3200DAA4DW - LBBWE-0535EPGW 2x512MB Kingston HyperX PC3200 (CH-5) 3dFuzion 7800GT 256MB, 400/1000 81.85 drivers Seagate 160GB SATA 300 NCQ hdd (8MB cache) Plextor PX-716SA/SW DL DVD Burner OCZ PowerStream OCZ600ADJ ATX 2.0 600W PSU * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 303 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 9x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.425v CPU VID Special Control - Above VID * 123% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.6v DRAM Configuration Settings: DRAM Frequency Set - 140=RAM/FSB:07/10 Command Per Clock (CPC) - Auto CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 02 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - AUTO Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - AUTO DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - AUTO IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.30: http://home.earthlink.net/~st919tte/sitebu...me-3dmark01.jpg 3dMark2003 + Aquamark: http://home.earthlink.net/~st919tte/sitebu...03-aquamark.jpg 3dMark2005 + Everest read: http://home.earthlink.net/~st919tte/sitebu...k05-everest.jpg ========== short description: 303x9 @ 2728Mhz, 1.425v + 123% three 120mm Case fans, no mods. 2-3-2-8 @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
TheFlowerKing Posted October 23, 2005 Posted October 23, 2005 DFI LANPARTY nF4 Ultra-D - 510-2FIX Bios AMD Athlon64 3200+ Venice on Big Typhoon 4x512 Geil TCCD (Ultra-X (Yellow) One S (Orange)) Galaxy 6600GT 128MB, 569/1280 77.72 drivers Samsung 80Gb SATA hdd (8MB cache) FSP BlueStorm 500W psu ========== Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.550v CPU VID Special Control - AUTO LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 2560 Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 1 Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE (23458) + CPU-Z 1.30: http://img461.imageshack.us/img461/8058/8h...ime3dm018ml.jpg 3dMark2003 (10055) + Everest 1.51 Memory Read (5582): http://img394.imageshack.us/img394/4526/3d...restread8bn.jpg 3dMark2005 (4287) + Everest 1.51 Memory Write (2240): http://img394.imageshack.us/img394/9765/3d...estwrite2qj.jpg Aquamark 3d (67499): http://img394.imageshack.us/img394/3241/aquamark0ce.jpg ========== short description: 270x10 @ 2700Mhz, 1.550v 4x512Mb @ 245MHz @ 2-3-6-3 @ 2.80v Share this post Link to post Share on other sites More sharing options...
nortius_maximus Posted October 24, 2005 Posted October 24, 2005 DFI LANPARTY nF4 Ultra-D - 6/23 stock bios AMD Athlon64 3000+ Venice REV F @ 2.7G ThermalRight XP-120 c/w Vantec SF12025L Stealth 120mm fan OCZ platinum rev 2 EL 1GB (2x512) dual kit DDR 400 (yellow slots) Sapphire ATI Radeon X800 GTO² 256MB GDDR3 unlocked all 16 pipes, 518/1044 omega drivers 2.6.71 Samsung SpinPoint P SP2004C 200GB SATA-II 8MB Cache (8MB cache) Pioneer DVR-110DBK 16 x 16 DVD±RW Dual Layer ReWriter Enermax Noisetaker 600W EG701AX-VE(W) SFMA ATX2.0 SLI Compliant PSU THERMALTAKE SOPRANO BLACK MIDDLE TOWER CASE WITH WINDOW * * ========== Genie BIOS Settings: FSB Bus Frequency - 299 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.300v CPU VID Special Control - Above VID * 123% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.90v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== cpu-z + Prime95 + 3dmark2001: http://www.angrygames.com/ocdb/paulwelford...dmark2001se.jpg 3dmark2003: 3dmark2005: Aquamark3d: Everest 1.51 Memory Read: ========== short description: 299x9 @ 2689Mhz, 1.300v + 123% 2.5-4-8-4 @ 2.9v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted October 25, 2005 Posted October 25, 2005 DFI nF4 DAGF - 08/11/2005 BIOS 4000 Sandy CABGE 0515SPWM 2x512mb Mushkin pc3500 Lev2 BH5 Power Color x850xt @ 580621 with Cat 5.9 1x 20gig Western Digital IDE drive ASUS IDE CD-ROM Drive OCZ 600w Power Stream SLI Edition Thermalright SLK948U with 92mm Panaflo * * * * ========== Genie BIOS Settings: CPU Frequency - 275 Hammer Fid Control - 10 HTT Frequency - 3 PCIE Clock - 100Mhz DDR Voltage Control - 3.2v Chip Voltage Control - 1.7v CPU Voltage - 1.625 DRAM Configuration Settings: Mem Clock mode - Limit Mem Clock Index Value - 200 (DRAM/FSB:1/01) CAS Latency Control (Tcl) - 2 Min RAS# active time (Tras) - 05 Bus Clocks RAS# to CAS# delay (Trcd) - 02 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DDR Output Driving - Normal DDR DQ Drive Strenth - Auto Bottom of 32Bit[31:24]IO - B0 1T2T Memory Timing - 1T Read Preamble Value - 5.5ns Async Latency Value - 7ns Dynamic IdleCycle Counter - 64 DRAM Bank Interleave - Enable Burst Length - 4 beats Enable ALL DIMM Clock - enable SW Memory hole remapping - disable HW Memory hole remapping - disable MTRR Mapping mode - continuous DRAM ECC Feature Control - disable ========== Prime95 + 3dMark2001SE + 2xCPU-Z : 3dMark2003 + SuperPi 1m : 3dMark2005 + Everest : Aquamark 3d: ========== short description: 275x10=2750mhz 1.625vcore 3.2vdimm Mem @ 230 2-5-2-2 Share this post Link to post Share on other sites More sharing options...
antistar Posted October 25, 2005 Posted October 25, 2005 DFI LANPARTY nF4 Ultra-D - 6-23 BIOS AMD Athlon X2 3800+ (Toledo Core) Crucial Value (2x1024MB) DDR PC3200 BFG 7800GTX 256MB, 490/1310 77.77 drivers Maxtor DiamondMax Plus 10 250GB SATA II 120GB 8MB cache IDE Nec 3500 DVD-RW Enermax EG565P-VE 535W Dell 2005fpw Lcd * * ========== Genie BIOS Settings: FSB Bus Frequency - 250 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.250v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.60v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/6 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z: http://www.down6.org/comp/2500stable2.jpg 3dMark2003: 3dMark2005 + Everest: Aquamark 3d: ========== short description: x2 3800+ @ 250x10 @ 2500Mhz, 1.250v + 113% 2.5-3-8-3 @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
Prostock62 Posted October 26, 2005 Posted October 26, 2005 DFI LANPARTY nF4 SLI-DR 7/02/05 Oscars Bios AMD Athlon64 3700 SanDiego 2x512MB Mushkin 3500 Lev11 (BH-5) EVGA 6600 GT 128MB 2 Hitachi Sata 11 80 Gig Raid0 (3.0) OCZ PowerStream OCZ520ADJ ATX 520W Power Supply - Retail ========== Genie BIOS Settings: FSB Bus Frequency - 255 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - x 11 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.400v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.40v DRAM Configuration Settings: DRAM Frequency Set - 200 (Dram/FSB: 1.1 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) Prime95 + 3dMark2001SE + CPUZ http://img485.imageshack.us/img485/284/prime2gw.png 3dMark2003 3dMark2005 Aquamark3d Everest Home Edition http://img367.imageshack.us/img367/2076/un...everest24pl.jpg Short Description 255x11 @ 2805 MHz 1.400v + 113% 2,3,3,7 @3.4 Vdimm 1.1 CPC-Enabled Share this post Link to post Share on other sites More sharing options...
Liquidfire Posted October 26, 2005 Posted October 26, 2005 DFI LANPARTY nF4 sli-DR - 7/04-2 BigToe BIOS AMD Athlon 64 3700+ 1GHz FSB Socket 939 Processor - Retail Crucial Ballistix ddr500 pc4000 eVGA Geforce 7800GT 256-P2-N518 Video Card - Retail 445/1070 Western Digital Caviar SE 300GB 3.5" Serial ATA150 Hard Drive - OEM NEC Black IDE DVD Burner Model ND-3540A - OEM OCZ PowerStream OCZ520ADJSLI 520W Power Supply - Retail * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 9X PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Auto CPU VID Control - 1.450v CPU VID Special Control - Above VID * 104% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.6v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Auto CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 3 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 3 Bus Clocks Row Cycle time (Trc) - 12 Bus Clocks Row refresh cyc time (Trfc) - 24 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 300x9 @ 2700Mhz, 1.450v + 104% 3-3-8-3 DDR540 (270) @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
deguello Posted October 27, 2005 Posted October 27, 2005 DFI LANPARTY nF4 UT SLI-D - 7/04-2 BigToe BIOS AMD Athlon 64X2 4800+ Toledo 2x1024MB OCZ Platinum EB PNY 7800GTX 256MB, 470/1300 81.85 drivers 4xHitachi 250GB SATA2 hdd NEC 3520a Black IDE DVD/CD-RW Drive PC Power & Cooling 510 Deluxe Power Supply ========== Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.425v CPU VID Special Control - Above VID * 110% LDT Voltage Control - 1.40v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - 01 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 6.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.30: http://www.netfrastructure.net/desktop.jpg 3dMark2003: 3dMark2005: Aquamark 3d: ========== I cannot run Everest Home because this computer is on a domain and Everest wants me to buy it because of this. This represents a lot of work and I have some comments to make about it later. I am pretty happy, but finding that I am bumping into a wall at 250 HTT. I have two sets of RAM that will do 250, but I cannot get them to prime for more than 15 minutes when they are at 250 or above. I have used all of my available time letely trying. short description: 270x10 @ 2700Mhz, 1.425v + 110% 3-3-2-8 @ 2.7v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted October 28, 2005 Posted October 28, 2005 DFI LANPARTY RDX200 CF-DR (10/26/2005 BIOS) AMD Athlon64 3200+ Venice 512k L2 2x512MB PC3200 GEIL ONE TCCD (GOS1GB3200DC) XFX GeForce 7800GT, 490/1310 81.85 drivers 160GB Maxtor IDE NEC 3540A Black IDE DVD-RW Drive Seasonic S12-600 (revA2) ATX 600W Power Supply - Retail * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 275 HT PLL High Speed............................. - Enabled LDT/FSB Frequency Ratio....................... - x 3.0 CPU/FSB Frequency Ratio....................... - x 10.0 CPU VID StartUp Value......................... - 1.500v NB-SB Port Configuration...................... - Enhanced CPU VID Control............................... - 1.450v CPU VID Special Control....................... - Above VID * 114.4% DRAM Voltage Control.......................... - 2.75v SB PCIE Voltage............................... - 1.8v NB Analog Voltage............................. - 1.3v LDT Bus Voltage............................... - 1.3v NB Core Voltage............................... - 1.3v [/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 06 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 7 DRAM Data Drive Strength...................... - Level 2 (Reduce 30%) Max Async Latency............................. - 8.0 ns DRAM Response Time............................ - 6.0 ns Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(8 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/rdx20...00_275x10-1.gif 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 275x10 @ 2750Mhz, 1.450v + 114.4% 2.0-3-6-3 @ 2.75v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now