davidk21770 Posted May 19, 2006 Posted May 19, 2006 DFI Lanforce UT nF4 SLI-DR Expert, BIOS: 04/06/2006 AMD Athlon64 4800+ Toledo 2x512G OCZ Platinum EL DDR400 (OCZ4001024ELDCPE-K) eVGA 6800 SLI (N383) GPU: 420 MHz/Memory: 770 MHz, 84.43 Forceware drivers Enermax Noisetaker / 600-Watt (EG701AX) Danger Den H2O Cooling: Brass Top TDX CPU Waterblock, DFI Expert Maze4 Chipset Waterblock, Black Ice XtremeII Radiator, D5 Pump (120 mm fan blowing on PWM Area & Memory) Promise RAID FastTrack S150/TX2Plus - 2@ WD1600JD (160G), Sil-3114 Raid - 3@ Hitchi DeskStar T7K250 (250G) SATA-II-300 HDT722525DLA380, Maxtor 6Y080LO 80 GB UDMA 6 ========== Genie BIOS Settings: FSB Bus Frequency - 232 LDT/FSB Frequency Ratio - 5.0 CPU/FSB Frequency Ratio - 12.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.35v CPU VID Special Control - Above VID * 119.2% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.52v DRAM Voltage Control - 3.17v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 0648 Cycles Odd Divisor Correct - Disable DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 08 DRAM Data Drive Strength - Level 1(Reduce 50%) Max Async Latency - 07.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 05.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + 3dmark05 + CPU-Z 1.31 + Everest 2.01: 3dMark2003: short description: Athlon 4800+ @ 2784Mhz, 1.35v * 119.2% 2.5-3-3-6 @ 3.17v vdimm Share this post Link to post Share on other sites More sharing options...
Guest caffeinejunkie Posted May 22, 2006 Posted May 22, 2006 DFI LANPARTY nF4 Ultra-D - 3/29/06 AMD Athlon64 3700+ San Diego skt939 2x512MB Muskin lvII V2 xp3200 (tccd) Sapphire x800gto Fireblade 256MB, 510/1200 Western Digital 40GB IDE hdd (8MB cache) Seagate 160gb IDE hdd (8mb cache) Sintek 500W Power Supply xp90 w/ Vantec 80mm Tornado Evercool VC-RE ========== Genie BIOS Settings: FSB Bus Frequency - 273 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 11x PCI eXpress Frequency - 104Mhz CPU VID StartUp Value - STARTUP CPU VID Control - 1.225v CPU VID Special Control - Above VID * 126% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.9v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4196 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 000 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.33.1: 3dMark2003: 3dMark2005: Everest: SuperPI 1.5 1m: ========== short description: 273x11 @ 3003Mhz, 1.225v + 126% 2-3-3-8 @ 2.9v vdimm Share this post Link to post Share on other sites More sharing options...
Wild Thing Posted May 23, 2006 Posted May 23, 2006 AMD Opteron 144 Venice 2x1GB OCZ Gold Edition 1GB PC-4000 OCZ5002048ELGE-K (UCCC) Biostar GeForce 6500 256MB , 400/532 8.1.9.5 drivers Maxtor 250GB IDE hdd (8MB cache) WD 250gb sata II hdd (16MB cache) ========== Genie BIOS Settings: FSB Bus Frequency - 290 LDT/FSB Frequency Ratio - X3 CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.450v CPU VID Control - 1.325v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.60v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clock DRAM Bank Interleave - Enabled DQS Skew Control - Increase Skew DQS Skew Value - 0 DRAM Drive Strength - Level 6 DRAM Data Drive Strength - Level Auto Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 7.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: 3dMark2003: 3dMark2005: ========== short description: 290x9 @ 2610Mhz, 1.325v + 113% 3-4-3-7 @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
Thraxz Posted May 24, 2006 Posted May 24, 2006 OPTERON 170 CBWE 0546 XPMW COOLED BY DANGER DEN TDX BRASS TOP WATER BLOCK DFI SLI -DR 6/23-3 Centon Advanced BH-5 512x2 PC4000 eVGA 7900GT 256 DDR3 COOLED BY DANGER DEN ACETAL MAZE4 WATERBLOCK 650/1680 DVD-RW PLEXTOR PX-740A HITACHI 80G P.O.S. SILVERSTONE 560W ZEUS ===========================«»============================== Genie BIOS Settings: FSB Bus Frequency - 285 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.475v CPU VID Special Control - 110% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.6v DRAM Voltage Control - 3.5v DRAM Configuration Settings: DRAM Frequency Set - 5/6 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 31.5 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 00 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 12 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - 8 DRAM Data Drive Strength - 1 Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 7.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Enable R/W Queue Bypass - 8 x Bypass Max - 04 x 32 Byte Granularity - Disable(8 Bursts) +++++++++++++++++++++++++++++++++++++++++++++++ Dual prime + 3dmark01+zcpu 3dmark03 3dmark05 3dmark06 Everest ----------------------------------------------<|>----------------------------------------------- 285x10 5:6 1.5-2-2-0-1T 1.62vcore 3.5vdimm Share this post Link to post Share on other sites More sharing options...
malvare1 Posted May 27, 2006 Posted May 27, 2006 DFI LANPARTY UT SLI EXPERT bios version 11/25/05 OPTY 165 CCBBE 0610DPMW@ 322x9 46c load prime stable :nod: XP-90 WITH HIGH SPEED DELTA FAN 79.81 CFM @ 4000 RPM 2x1 GIG PC4000 GX XTC @241.5MHZ (150 DIVIDER)3/4/3/8 1T 2 x BFG 7800 GT OC SLI@477/1.13 2 WD 250 GIG RAID EDITION on RAID 0 AUDIGY 2 ZS NEC 3500A ENERMAX NOISETAKER 600 Antec p160 Sony P234 widescreen 23" ================================================ FSB Bus Frequency..................... 322 LDT/FSB Frequency Ratio............... 3.0x CPU/FSB Frequency Ratio............... 9x PCI Express Frequency................. 100 CPU VID Startup Value................. Startup CPU VID Control....................... 1.425 VID Special Control................... 107.2% LDT Voltage Control................... 1.40V Chip Set Voltage Control.............. 1.62v Dram Voltage Control.................. 2.71v DRAM Configuration Settings: Dram Frequency Set (Mhz).............. 150=RAM/FSB:03/04 Command Per Clock (CPC)............... Enable CAS# latency (Tcl).................... 3.0 RAS# to CAS# delay (Trcd)............. 03 Min RAS# active time (Tras)......... . 08 Row Precharge Time (Trp).............. 03 Row Cycle Time (Trc).................. 11 Row refresh timg (Trfc)............... 16 RAS# to RAS# delay (Trrd)............. 03 Write Recovery Time (Twr)............. 03 Wite-to-Read Delay (Twtr)............. 02 Read-to-Write Delay (Trwt)............ 03 Refresh Rate (Tref)................... 3120 Cycles Write CAS Latency (Twcl)...............Auto DRAM Bank Interleaving................ Enabled DQS Skew Control...................... Auto DQS Skew Value........................ 0 Ram DLL Speed......................... Auto DRAM Drive Strength................... Level 07 DRAM Data Drive Strength.............. Level 2 Max Asynchronous Latency.............. 08.0 DRAM Response Time.....................normal Read Preamble Time.................... 6.5 IdleCycle Limit........................128 Dynamic Counter....................... Disable R/W Queue Bypass.......................16X Bypass Max.............................04X 32-Byte Granularity................... Disable (4 bursts) ======================================== Dual Prime Share this post Link to post Share on other sites More sharing options...
Prostock62 Posted May 28, 2006 Posted May 28, 2006 DFI LanParty SLI-DR Expert AMD Opteron 146 CABYE 0540 FPAW G-Skill 4800 1GBLA 2x512MB EVGA 6600GT 128MB 2 Hitachi Sata 11 80Gig Raid0 OCZ PowerStream 520W ATX Lian Li 6077 BLK Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - AUTO PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.400v CPU VID Special Control - Above VID * 114% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.68v DRAM Voltage Control - 2.90v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Dis CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 10 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 10 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 1.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 8 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) http://img89.imageshack.us/my.php?image=ne...e95bench7iq.jpg Short Description AMD Opteron 146 @300x10 3000.7MHZ 1.400 Vcore 2.90V VDimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted May 30, 2006 Posted May 30, 2006 DFI LANPARTY CFX3200-DR (5/23/2006 BIOS) AMD Athlon64 X2 4400+ Toledo 1MB L2 2x1024MB OCZ PC4000EB Platinum Radeon X1900 CrossFire Edition 512MB, 690/1600 CAT 6.5 drivers + Radeon X1900XT 512MB, 690/1600 CAT 6.5 drivers 2x80GB Hitachi SATA II hdd NEC 3540A Black IDE DVD-RW Drive OCZ GameXStream OCZ700GXSSLI ATX12V 700W Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 260 LDT/FSB Frequency Ratio....................... - x 4.0 CPU/FSB Frequency Ratio....................... - x 10.0 RD580 HT PLL Speed............................ - High Speed HT Bus MMOS Drive Strength.................... - 05 HT Bus PMOS Drive Strength.................... - 05 HT Bus Receiever Impedance.................... - 10 CPU HT Bus Drive Strength..................... - Normal CPU VID Control............................... - 1.525v CPU VID Special Control....................... - Above VID * 101.4% DRAM Voltage Control.......................... - 2.67v SB PCIE Voltage............................... - 1.80v NB Analog Voltage............................. - 1.34v LDT Bus Voltage............................... - 1.34v NB Core Voltage............................... - 1.34v [/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 Bus Clocks RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 02 Bus Clocks Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled Errata 94 Enhancement......................... - Disable Errata 123 Enhancement........................ - Auto Odd Divisor Correct........................... - Disable DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 1 (Reduce 50%) DIMM 1/3 Clock Timing Skew.................... - Auto DIMM 2/4 Clock Timing Skew.................... - Delay 450ps Max Async Latency............................. - 8.0 ns Read Preamble Time............................ - 6.0 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 4 x Burst Length.................................. - 4 Bursts [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/cfx32...EB_260x10-1.gif 3dMark2003: 3dMark2005: 3dMark2006 Aquamark 3d: F.E.A.R. 1.03 @ 1280x960, 4xAA/16xAF, all graphics maximized, Soft Shadows = OFF: Half-Life 2: Lost Coast @ 1280x1024, 4xAA/16xAF, HDR enabled, all graphics maximized: ========== short description: 260x10 @ 2600Mhz, 1.525v + 101.4% 3.0-3-8-2 @ 2.67v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted May 30, 2006 Posted May 30, 2006 DFI LANPARTY RDX200 CF-DR (12/23/2005 BIOS) AMD Athlon64 3200+ Venice 512k L2 2x1024 OCZ PC4000EL Gold (OCZ5002048ELGE-K) Radeon X1900 CrossFire Edition 512MB, 690/1600 CAT 6.5 drivers + Radeon X1900XT 512MB, 690/1600 CAT 6.5 drivers 2x80GB Hitachi SATA II hdd NEC 3540A Black IDE DVD-RW Drive OCZ PowerStream OCZ520ADJSLI ATX, BTX, EPS12V 520W Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 250 HT PLL High Speed............................. - Enabled LDT/FSB Frequency Ratio....................... - x 4.0 CPU/FSB Frequency Ratio....................... - x 10.0 CPU VID StartUp Value......................... - 1.550v NB-SB Port Configuration...................... - Enhanced CPU VID Control............................... - 1.500v CPU VID Special Control....................... - Above VID * 102.4% DRAM Voltage Control.......................... - 2.75v SB PCIE Voltage............................... - 1.8v NB Analog Voltage............................. - 1.3v LDT Bus Voltage............................... - 1.3v NB Core Voltage............................... - 1.3v [/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 Bus Clocks RAS# to CAS# delay (Trcd)..................... - 04 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 04 Bus Clocks Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - AUTO DRAM Data Drive Strength...................... - AUTO Max Async Latency............................. - 8.0 ns Read Preamble Time............................ - 6.0 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 4 x 32 Byte Granularity........................... - Disable (8 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/rdx20..._250x10EL-1.gif 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: ========== short description: 250x10 @ 2500Mhz, 1.500v + 102.4% 3.0-4-8-4 @ 2.75v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted May 30, 2006 Posted May 30, 2006 DFI LANPARTY nF4 SLI-DR - 7/04/2006 BIOS (7/04-2BTA) AMD Opteron 146 Venus 2x1024MB OCZ PC4000 Gold GX "XTC" XFX 7800GT 256MB PCI-E, 499/1150 84.66 drivers 160GB Maxtor IDE, 160GB Seagate SATA NEC 3540A Black IDE DVD-RW Drive Skyhawk 520w Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 250 LDT/FSB Frequency Ratio....................... - AUTO CPU/FSB Frequency Ratio....................... - Auto PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.500v CPU VID Special Control....................... - Above VID * 102.4% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - By DRAM SPD Value Command Per Clock (CPC)....................... - Enabled CAS Latency Control (Tcl)..................... - 3.0 Bus Clocks RAS# to CAS# delay (Trcd)..................... - 04 Bus Clocks Min RAS# active time (Tras)................... - 09 Bus Clocks Row precharge time (Trp)...................... - 04 Bus Clocks Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 8.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 6.0 Nano Seconds IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/duane_146_s...46_sli-dr-1.gif 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: ========== short description: 250x10 @ 2500Mhz, 1.500v + 102.4% 3.0-4-9-4 @ 2.80v vdimm Many thanks to sw4y for letting me put his rig in the OC Database! Share this post Link to post Share on other sites More sharing options...
OldGuy Posted June 4, 2006 Posted June 4, 2006 LanParty NF4 Ultra D - BIOS 406 Official AMD Opteron 150 Venus IHS Removed 2GB Geil One tccd 4 X 512 XFX 7900GTX 512MB - 665/1630 84.43 beta drivers 2 X Western Digital 250gb RE WD2500YD Raid Specific SATA II RAID 0 (16MB cache) Enermax EG701AX-VE SFMA 600W Coolit Systems Freezone CPU Cooler * * ========== Genie BIOS Settings: FSB Bus Frequency - 242 LDT/FSB Frequency Ratio - X 4.0 CPU/FSB Frequency Ratio - X 12.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.400v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.90v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 10 Bus Clocks Row refresh cyc time (Trfc) - 12 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3072 Cycles (200MHz 3.9us) DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Weak 7 DRAM Data Drive Strength - Auto Max Async Latency - 7.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.5 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.33 + Everest 2.01: 3dMark2003: 3dMark2005: 3dmark 2006: Aquamark 3d: Everest Write: Everest Latency: Sandra Bandwidth: SuperPI 1M: HDtach: ========== short description: 242 X 12 @ 2904 Mhz 1.400v + 113% 2-3-7-3 @ 2.90v vdimm Share this post Link to post Share on other sites More sharing options...
l3lackh0le Posted June 7, 2006 Posted June 7, 2006 i hope i did this right....here goes nothing, my first ocdb. DFI LANPARTY nF4 SLI-DR - 704-2bta BIOS AMD Opteron 165 dual core CCBBE 0610DPMW OCZ 2GB (2 x 1GB) 184-Pin DDR SDRAM Dual Channel Platinum Model #: OCZ4002048ELDCPE-K Leadtek 7800GTX 256MB, stock Western Digital Raptor 74GB 3.5" Serial ATA150 Hard Drive NEC 16X DVD±R DVD Burner Black IDE/ATAPI Model ND-3550A flashed to 4551a OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail Zalman cnps9500 led cpu cooler * * ========== Genie BIOS Settings: FSB Bus Frequency - 325 LDT/FSB Frequency Ratio - x 3.0 CPU/FSB Frequency Ratio - x 9.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.350v CPU VID Control - 1.375v CPU VID Special Control - Above VID * 110% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 150=RAM/FSB:03/04 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 12 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 1168 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - normal 4 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - normal Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== dual Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest memory read: dual super pi + smartguardian + everest memory write + 3dMark2003: Everest memory latency + 3dMark2005: Aquamark 3d: ========== short description: 325*9 @ 2925mhz @ 1.375v + 110% 3-3-3-5 @ 2.8v vdimm Share this post Link to post Share on other sites More sharing options...
dbilz Posted June 7, 2006 Posted June 7, 2006 Here goes DFI LANPARTY nF4 Ultra-D - 6/23-2 AMD Opteron 165 toledo 2x1GB G.Skill es (UCCC) eVGA 7600GT 256mb, 600/1580 91.28 betas WD Caviar SE16 250GB SATAII 16mb cache BenQ 16X DVD±R DVD Burner With SolidBurn Black ATA/ATAPI OCZ PowerStream OCZ520ADJSLI 520W Power Supply * * Need cam for bios, comming soon. * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 9x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.425v CPU VID Special Control - Auto LDT Voltage Control - 1.40v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.65v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 1 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - normal Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.34.1 + Everest 2.80.534: 3dMark2003 + Sandra Lite 2007.5.10.98: 3dMark2005 + a64info 0.5: 3dMark2006 + dual SuperPI: ========== short description: 300x9 @ 2700Mhz, 1.425v 3-4-4-8 @ 2.65v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now