Vortexics Posted May 10, 2005 Posted May 10, 2005 THis is are the settings I got, if there anything wrong with it just let me know to try something diferent. you got my syste configuration cpu,mem,etc Genie BIOS Settings: FSB Bus Frequency - 266 LDT/FSB Frequency Ratio - Auto CPU/FSB Frequency Ratio - 9x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.400v CPU VID Control - 1.400v CPU VID Special Control - Auto LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.9v DRAM Configuration Settings: DRAM Frequency Set - 150 (DRAM/FSB:3/04) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - Auto Min RAS# active time (Tras) - Auto Row precharge time (Trp) - Auto Row Cycle time (Trc) - Auto Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - Auto Write recovery time (Twr) - Auto Write to Read delay (Twtr) - Auto Read to Write delay (Trwt) - Auto Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - auto DRAM Data Drive Strength - Level 4 Max Async Latency - 07.0 nano secs Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) Share this post Link to post Share on other sites More sharing options...
dspayre Posted May 11, 2005 Posted May 11, 2005 THis is are the settings I got, if there anything wrong with it just let me know to try something diferent. you got my syste configuration cpu,mem,etc Below are your settings, I will put my comments to changes you should make. ===================================================== Genie BIOS Settings: FSB Bus Frequency - 266 LDT/FSB Frequency Ratio - Auto --> STEP1: change this to 3x CPU/FSB Frequency Ratio - 9x PCI eXpress Frequency - 100Mhz --> STEP3: change voltage settings CPU VID StartUp Value - 1.400v -->1.425v CPU VID Control - 1.400v CPU VID Special Control Auto -->104% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.9v DRAM Configuration Settings: DRAM Frequency Set - 150 (DRAM/FSB:3/04) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 --->STEP2: change mem settings RAS# to CAS# delay (Trcd) - Auto ---> 3, 4 if not stable at 3 Min RAS# active time (Tras) - Auto --->8 Row precharge time (Trp) - Auto --->3, 4 if not stable at 3 Row Cycle time (Trc) - Auto Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - Auto Write recovery time (Twr) - Auto Write to Read delay (Twtr) - Auto Read to Write delay (Trwt) - Auto Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - auto DRAM Data Drive Strength - Level 4 Max Async Latency - 07.0 nano secs Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ================================================== now, do these changes in steps. change the LDT setting then run memtest and prime to see if you are stable...if not change your dram timings in step2....run memtest and prime again.....if step2 fails....do step 3 by uping the voltage, the settings i gave you are very conservative on the voltages....if you are overclocking i believe you need more....kinda like my settings in my sig....but again back to the same question of how far you are going to risk. Share this post Link to post Share on other sites More sharing options...
dspayre Posted May 11, 2005 Posted May 11, 2005 dspayre throttling is disabled, I followed rgone's settings and here is my bios settings... Your Bios settings are below please see my comments. I have not OCed with a newcastle, is it able to take more voltage than the winnies? How are your temps? ========================================================= DRAM Config FSB BUS Frequency 260 LOT/FSB Frequency Ratio X3.0 LOT BUS Transfe Width 16-16 CPU FSB Frequency Ratio X10.0 PCI Express Frequency 100 MHZ Cooler Quiet Disable CPU VID Startup Value 1.525v CPU VID Control 1.525v CPU VID Special Control Above VID *110 LOT Voltage Control 1.50v Chipset Voltage Control 1.80v DRAM Voltage Control 3.40v ---> do you have UTT's? (high voltage) 180 (DRAM/FSB:S/P) CPC Dis/Auto ----> disable means your running at 2T? Try 1T, but prolly less stable at 1T --->you could try relaxing the timings TCL 2.5 ----> maybe 3 TRCD 03 --->4? TRAS 06 ---> 8 TRP 03 ---> 4? TRC 07 TRFC 14 TDRP 05 TWR 03 TWTR 02 TRWT 05 TREF 3120 TWCL 05 ====================================================== is bank interleave disabled? you can try playing with this to see which is more stable....what are your DRAM drive strength settings? You can try to change these to increase your stability....a good idea is to try and find out what chips are on your sticks (UTT, TCCD, etc) then you will have a better idea on what to set your timings and drive strengths. It's really a lot of trial and error and patience....sorry I could not give you a better solution....good luck! Share this post Link to post Share on other sites More sharing options...
Vortexics Posted May 11, 2005 Posted May 11, 2005 dude I tried every one of the steps one by one in the order you gave me, everytime I past a test on prim95 it fails after not even 10 secs, then I put the settings at stock to check if prime95 wasn't running wrong or something, and prime95 ran fine at stock settings, I dunno which lower settings should I use at least to go for 2.2 ghz or something like that I think it is the memory volts, and besides that i ain't using dual channel I just have 1 stick of 512MB :confused: . anyways thanks for all you been helping me. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now