Isamu77 Posted April 3, 2005 Posted April 3, 2005 i have flashed from 10/05 to 1/28 couldnt notice any differences in temps Quote Share this post Link to post Share on other sites More sharing options...
gordesky1 Posted April 4, 2005 Posted April 4, 2005 wll i think it ben 3 days still hot runing 60c right now with prime maybee my load temps are wrong? my idel temps are 34 too 37 my pwmic is ony from 26 too 33 at full load system is at 25 too 33 at full load. is there a anotherway too detected my temps right? i herd about a temp probes but i can not find them online were can i buy one at? Quote Share this post Link to post Share on other sites More sharing options...
Smoken Joe Posted April 4, 2005 Posted April 4, 2005 wll i think it ben 3 days still hot runing 60c right now with prime maybee my load temps are wrong? my idel temps are 34 too 37 my pwmic is ony from 26 too 33 at full load system is at 25 too 33 at full load. is there a anotherway too detected my temps right? i herd about a temp probes but i can not find them online were can i buy one at? You cant get below the ambient temp of your case. What are your case temps? Do you have good case flow expecaly around your CPU cooler? Quote Share this post Link to post Share on other sites More sharing options...
gordesky1 Posted April 4, 2005 Posted April 4, 2005 how can i tell the case temp? i know i wont get down too ambient temp. but shouldint i be runing atleast 48 too 50 at 1.64vcore? right now i got it back too 1.5vcore 2.5ghzs and its at 48 too 50 at full load thats what i thought it whould be with 1.64vcore. i got 120mm fan in front below my cdrom blowing in and i got a 120mm fan in back blowing out than i got a 80mm 5000rpm fan below the video were the pci slots are blowing out fo the back at 580rpms. so i whould think the air in my case is good. Quote Share this post Link to post Share on other sites More sharing options...
ViperJohn Posted April 4, 2005 Posted April 4, 2005 You will see alot better results with AS5... I dropped my 7000 in using cermique and wasnt pleased, so i tried AS5 and had 10c drop in temps from stock heat sink :nod: Also it takes over 200 hrs PLUS for AS5 to set completly... Then you did something wrong when you used the Ceramique. At the most the temp difference will about 2C. Viper Quote Share this post Link to post Share on other sites More sharing options...
gordesky1 Posted April 4, 2005 Posted April 4, 2005 ok i put a house themomler in the case. and its at 82f and 25c? Quote Share this post Link to post Share on other sites More sharing options...
marscay Posted April 4, 2005 Posted April 4, 2005 i am assuming you don't have a winchester, still 1.64v is a fair amount of voltage on air - you can't expect good temps unless you switch to a XP-120 and a high cfm noise monster. Quote Share this post Link to post Share on other sites More sharing options...
OBR Posted April 4, 2005 Posted April 4, 2005 I have on Winchester (2640Mhz, 1.63V) with Zalman idle:33, full load: 45. Quote Share this post Link to post Share on other sites More sharing options...
gordesky1 Posted April 4, 2005 Posted April 4, 2005 mine is a newcastle 3000. theres nothing cant be wrong with the zalman could it? Quote Share this post Link to post Share on other sites More sharing options...
gordesky1 Posted April 4, 2005 Posted April 4, 2005 i got a blow hole in my side panel with a green cup on it. and i was wondering should i take the cup off than mount the 80mm 5000rpms that i have here http://img135.exs.cx/img135/2335/inside30wn.jpg too the blow hole blow over top of the zalman blowing in or out? or should i keep the cup on than put the fan on the end of that? heres a pic of my side panel http://img71.exs.cx/img71/165/sidewindow3zk.jpg the top pic is were the 80mm is. Quote Share this post Link to post Share on other sites More sharing options...
gordesky1 Posted April 4, 2005 Posted April 4, 2005 hmm i just tried that 80mm blowing over top of the zalman and it didint do anything. and i had it at 5000rpms:( so i gess i need a temp probe were can i find one? Quote Share this post Link to post Share on other sites More sharing options...
Isamu77 Posted April 4, 2005 Posted April 4, 2005 have you tried mounting it in a different direction if that can be done my stuff arrives tommorow and after reading this thread i guess lower temps arent going to happen i hope its quieter than stock HSF otherwise its just gonna be a cosmetic purchase which is waste of money for me Quote Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.