Jump to content
Sign in to follow this  
Guest Hellfire_merged

Hellfire's 6/19 Bios With 12/18 ROMSIP

Recommended Posts

heheheehee, just fired up prime95 about 3 minutes ago, fingers crossed, man i hope this holds out im so happy, please hold out.

 

Your da man hellfire

 

:shake: :nod: :angel:

Share this post


Link to post
Share on other sites

No prob, mong :D

 

Erm, you say the bios fixes your LAN probs totally?

 

My sound probs still were apparent... but I probably try again tomorrow.

Share this post


Link to post
Share on other sites

just flash Hellfire's 3EG Bios for Infinity Rev. #1, and it good, no cold boot and warm boot

only need low volt for cpu....last time need 1.74 and now only used 1.65 for o/c 13.5 * 166

and it also give +100 score in 3dmarks 2001se... good work hell fire..

waiting for Hellfire's 3EG Bios for Infinity Rev. #2

Share this post


Link to post
Share on other sites
Originally posted by mongoled

heheheehee, just fired up prime95 about 3 minutes ago, fingers crossed, man i hope this holds out im so happy, please hold out.

 

Your da man hellfire

 

:shake: :nod: :angel:

 

 

:nod: :nod: :nod: :nod: :nod: :nod:

The only bios what run prime for me.

 

Thanks again, Hellfire

Share this post


Link to post
Share on other sites
Guest rcillig

ok I got it flashed but my 3dmark2001 score is like 1500 less..... that always sucks when it goes down instead of up.

Share this post


Link to post
Share on other sites
Guest Hellfire
Originally posted by rcillig

ok I got it flashed but my 3dmark2001 score is like 1500 less..... that always sucks when it goes down instead of up.

 

Are you sure which bios are you using and is anything different from before?

Share this post


Link to post
Share on other sites
Guest rcillig

yes I flashed to the hellfire N24LD619-Hell-3EG and was using the 1-31-04 before.

Share this post


Link to post
Share on other sites

Hale, I gotta post this, never been this high before:D

 

The LanParty on Hellfire 6/19 C-18

XP-2600M (the bad "a" stepping) @1.975v

2x512 Mushkin Special 2-2-2 BH-6 at 3.3v 11-3-2-2-2.0-e-e-f-CPC ON all others AUTO

2x36G Raptors Raid 0 @ 32/16 116.5mb/s burst 8.7 access

9800Pro w/ ViperJohn Mods

Antec TruBlue 480, Antec SX-1030B Case with lots O fans

and a whole nunch of other stuff

 

2701.JPG

 

24/7 at 240x11 and a little clock generator to get up to 245 (hehehe)

Played around for a half hour or so and took some screenies so ya wouldn't think I was fibbin!

Of course it rebooted when I tried to run 3D01 as well, but it was fun as hale while it lasted.:nod:

Share this post


Link to post
Share on other sites

Nice results, Carl :D... too bad it could not do 3d :(

 

But I am impressed by these mushkin 3200 512MB modules! They can do CPC on at 240+??? Wow, I must admit.

Share this post


Link to post
Share on other sites

Thanks Stefan, I wouldn't have touched your 3d score anyways so no big deal. hehehe. I'm trying to burn it in further but I'm afraid the best I'll get is 240 11-3-2-2. but hale for 512 sticks I'm happier than a pig in ., Yes with CPC ON.

Share this post


Link to post
Share on other sites
Guest Hellfire

Have I got a new bios for you all, a custom tuned bios allowing for a higher hsb, which doesn't stress the memory controller as much, it has alowed me as much as 5 fsb on my mush lvl2 512mb module, as now I can run 245 fsb with cpc on. The release date is still not certain but check back in a few days.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×