Jump to content

LianLi Lancool K62 Water Cooling Reconfiguration and Case Mod


wevsspot

Recommended Posts

Since I've got little grandkids running around the house all of the time now, I needed to protect curious little fingers from the fans on my externally mounted MCR220 Drive Series Rad/Res/Pump. I could have just put fan guards on I guess, but I got motivated and decided to completely reconfigure my watercooling setup instead of taking the easy way out.

 

Parts used;

 

2x140mm stock LianLi fans

Black Ice GT 240 Stealth Radiator

XSPC Dual Bay Reservoir

Swiftech MCP655-B Pump

Swiftech Apogee XT (already had so re-used)

 

The first order of business was moving the 2x140 fans from the top exterior of the case to the top interior of the case. Not much hassle here other than it being a tight fit. That almost made enough room height wise to squeeze the radiator between the top of the case and the top bezel, but not quite because I wanted to re-use the original screws and rubber insulator grommets to hold the 140mm fans in place. So that left me about 1/8" shy of fitting the radiator between the case and bezel. So out came the trusty jig saw and dremel. I removed the slotted fins from the top of the bezel. That exposed the radiator and gave me enough height to finsih the job.

 

I didn't take photos along the way, but I did get some snap shots of the finished product before final cleaning and polishing. Here are the results;

 

dscf3021c.jpg

 

dscf3018b.jpg

 

dscf3013b.jpg

 

dscf3012n.jpg

 

dscf3011a.jpg

 

dscf3010o.jpg

Edited by wevsspot

Share this post


Link to post
Share on other sites

I was thinking of doing the same thing with my K58 but with a thicker radiator because no rad will fit under that top grate. I think a 2.25 inch rad would look nice sticking out of the to a bit.

Share this post


Link to post
Share on other sites

I almost went with a little thicker radiator too, because I agree with you, it would look pretty cool protruding from the top just a little bit. In the end I settled on the Black Ice because I was fond of the color :)

 

El Capitan - you'll love the dual bay. It is pretty darn sweet. And, thanks for buying that MCR Drive Series from me. That help offset my cost a little bit. I appreciate it!

Share this post


Link to post
Share on other sites

  • 7 months later...

hello

hope i'm still not late to reply on this thread :)

wevsspot

i'm wondering how u attach the 240mm radiator on the top because this casing using 140mm fan on top,hope u can explain it to me

p/s:using same casing as yours

thanks

Edited by napster2142

Share this post


Link to post
Share on other sites

Move the two 140mm fans from the top of the case to the inside of the case (they can be mounted in either location). Decide whether you want the fans to push or pull. In my configuration I've actually got the fans pushing air from inside the case, through the radiator and then out the top.

 

For the actual mounting of the radiator.... it is just set on top of the case frame and secured into place with the top cover. No fancy mounts or brackets. Here's a pic. showing the fans moved to the inside of the case;

 

5398833537_f3cb2ed58a_b.jpg

Share this post


Link to post
Share on other sites

nice one bro, thanks

at 1st u're panning to use Swiftech MCR220 right?but why change it to Black Ice GT 240 Stealth Radiator?

i'll buy Swiftech MCR220 soon and this radiator is thicker than GT 240 and i'm most wondering now about the hubs,because its wider than GT 240 and afraid doesn't suit the 2 pre-holes on the top of the casing.

so,in your opinion,does the MCR220 fit nicely with this casing? (after modding the hazel)

Share this post


Link to post
Share on other sites

Not sure Napster. I specifically used the Black Ice because after measuring I knew for sure that it would fit without having to do a lot more trimming on the top bezel. With the Black Ice all I needed to remove were the vent slots, so it was an easy cut, sand and paint. If I had used a thicker radiator I would have had to make some more complex cuts and trims in the bezel.

 

Regarding just the hole placement for the hoses, I believe that the pre-cut holes would accommodate most inlet/outlet barbs of any radiator.

 

Here are a few more pictures after the case was painted;

 

dscf3189i.jpg

 

dscf3037l.jpg

Share this post


Link to post
Share on other sites

wow,as expected man,u've painted it white,i also planning to do so :) nice work done there!

 

i just realized at your 1st post,i can see "the gray thing" on the top hazel,what is it?its like size of the radiator is smaller than the space provided after the cutting and u try to fit it nicely,am i right?

Swiftech MCR220 dimension is 284 x 128 x 34 mm while Black Ice is 277 x 133 x 29.60 mm,so ST is a bit longer and thicker,so,in my opinion its still need to remove the fin only,no need to adjust others,i think u know what i mean.

Share this post


Link to post
Share on other sites

The "gray" piece is a filler. I cut out all of the vent slots and that left a slightly longer hole than the radiator would fill. Another option would be to leave two vent slots at the front and not use a filler. I made my filler out of an old 5.25" front bay cover. It looks grey because it was sanded down in prep for primer and paint at that point.

Share this post


Link to post
Share on other sites

as expected the cutting should provide enough space for 240mm radiator,okay bro,thanks for all the information,starting to use WC system :)

if i'm using cooler master haf-x,its should not be any problem for me,but dont want to spend more bucks for casing :)

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
×
×
  • Create New...