Smiki007 Posted August 10, 2010 Posted August 10, 2010 ok, i'll do that. What about the cooler (mine Thermaltake Hyper N520) should i go for (let's say) V6 GT or V8, (it's very difficult to find good cooler in peruvian market). Share this post Link to post Share on other sites More sharing options...
wevsspot Posted August 10, 2010 Posted August 10, 2010 Do you mean CoolerMaster? That one is fine for now. When you get a chance you might research the the Noctua NH-D14. Very pricey, but it is the best air cooler on the market righ tnow. Hurry up, get that blck up to 162 and let me know how it goes Once you do that let me know what your new DRAM frequency is too. We may still have a little room to play Share this post Link to post Share on other sites More sharing options...
Smiki007 Posted August 10, 2010 Posted August 10, 2010 yeah it's coolermaster, and about Noctua NH-D14... i would like.. but i'll not find it here (Lima, Peru !?!?), i'll stay for now with Hyper N520. BCLK 162 sounds tempting, i'll try later (now I'm at work far from home), and will post the results tomorrow. Regards, Smiki Share this post Link to post Share on other sites More sharing options...
wevsspot Posted August 10, 2010 Posted August 10, 2010 Ok. Keep me posted. Regards, Share this post Link to post Share on other sites More sharing options...
Smiki007 Posted August 11, 2010 Posted August 11, 2010 (edited) Wev, done it, new config. below (red bold) CPU CLOCK RATIO: 24X CPU FREQUENCY: 3.84GHz 3.88 GHz INTEL TURBO MODE: DISABLED INTEL C1E STATE: ENABLED C3/C6/C7 STATE: DISABLED CPU THERMAL MONITOR: ENABLED DISABLED CPU EIST FUNCTION: ENABLED BI-DIRECTIONAL PROCHOT: ENABLED QPI CLOCK RATIO: AUTO QPI LINK SPEED: 5.76GHz 5.83 GHz UNCORE CLOCK RATIO: AUTO UNCORE FREQUENCY: 3200MHz 3240 MHz BCLK: 160MHz 162 MHz SYSTEM MEMORY MULTIPLIER: 8.0 MEMORY FREQUENCY: 1280MHz 1296 MHz PCI EXPRESS FREQUENCY: AUTO CPU CLOCK DRIVE: 700Mv 800mV PCI EXPRESS CLOCK DRIVE: 700Mv 900mV CPU CLOCK SKEW: OPS IOH CLOCK SKEW: OPS MEMORY CHANEL TIMING (A, B, C): 9-9-9-24 (EVERYTHING ELSE AUTO) VOLTAGE SETTINGS CPU VCORE: 1.26875 1.28750 QPI/VTT: 1.315 DRAM: 1.540 PCIE: AUTO CPU PLL: AUTO QPI PLL: AUTO IOH CORE: AUTO ICH I/O: AUTO ICH CORE: AUTO DRAM TERMINATION: AUTO CH-A DATA VRERF: AUTO CH-B DATA VRERF: AUTO CH-C DATA VRERF: AUTO CH-A ADRESS VREF: AUTO CH-B ADRESS VREF: AUTO CH-C ADRESS VREF: AUTO ISOCHRONUOS SUPPORT: ENABLED VIRTUALIZATION TECHNOLOGY: ENABLED Regards, Smiki Edited August 12, 2010 by Smiki007 Share this post Link to post Share on other sites More sharing options...
ezwanzazi Posted August 12, 2010 Posted August 12, 2010 (edited) guys i need help,i have problem starting my pc, is it because of my graphic card or ram?i'm using mboard asus iv formula and if i'm not mistaken there should be a beep everytime i try to turn on the pc(showing that vga card is detected) then i need to force a shut down and turn on again to boot into windows.sorry, i'm still a noob..please bear with me.. my pc specs: phenom ii x6 1090t asus crosshair iv formula 1tb western digital 64mb xfx 5770 750w silverstone 2x2gb corsair 1600mhz Edited August 13, 2010 by ezwanzazi Share this post Link to post Share on other sites More sharing options...
ezwanzazi Posted August 12, 2010 Posted August 12, 2010 (edited) i did the memory diagnostic scan and it said that hardware problem found,plus after the force shutdown and turning the pc back on,the bios post message stated that overclocking failed..pls help bcause i heard if i keep on doing this it may harm my mboard Edited August 12, 2010 by ezwanzazi Share this post Link to post Share on other sites More sharing options...
Smiki007 Posted August 12, 2010 Posted August 12, 2010 according to your mobo specs only support double channel memory, (check yours memory specs), check is everything is attached well and properly in your mobo, post all your bios config regards, Smiki Share this post Link to post Share on other sites More sharing options...
ezwanzazi Posted August 12, 2010 Posted August 12, 2010 yaa..my fault, it's 2x2gb corsair 1600mhz(9-9-9-24), i did check and eveything's attached correctly.is it possible that the problem is bcause the mobo doesnt detect the graphic card?i've heard many complains on the 5770 faulties but wth i should've done research about it better before creating my pc.i will post the bios config in a few days bcause i'm currently away from my pc. regards, ezwan Share this post Link to post Share on other sites More sharing options...
Smiki007 Posted August 12, 2010 Posted August 12, 2010 OK, lol keep me posted regards, Smiki P.S. about video cards ATI don't know much... I'm NVIDIA fan. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now