Jump to content
Sign in to follow this  
motoray

overclock need help

Recommended Posts

ima be workin hard this weekend to try and reach near 280fsb ima go for the amd k8 frequency record. once i sort out the fsb just gotta get me a dice pot and start cranking!!

 

Well i dropped my multi to 14 started raising fsb crashed at 238 where it couldnt find device to boot or whatev. i even dropped my ht link to 800 before so im a lil confused with ht-nb at 1.3v do you have your vdda volts set to something mine is still on auto?

Edited by motoray

Share this post


Link to post
Share on other sites

I only changed the NB and HT link volts. they are both at 1.26. and I put my HT back to 1000 set so that puts my ht at 1200. I have been Tweaking hard at this point..... I now need an external cmos reset switch.

 

On a Side note, Why a Dice pot.... If there is a dice but there must be a video. :D

 

Here is My CPU ID

605281.png

Edited by boinker

Share this post


Link to post
Share on other sites
On a Side note, Why a Dice pot.... If there is a dice but there must be a video. :D

 

Here is My CPU ID

605281.png

 

dice = dry ice so i can run like -60c and get 4.3ghz if i can get my freckin fsb up i dont understand why its not going further. Your way past with less volts than me. Also wondering what is ur vdda and nf 200 chip voltage at. at ht 800mhz and 1.3v and nb at 1.3v 238fsb should be no problem. http://valid.canardpc.com/show_oc.php?id=604271

Edited by motoray

Share this post


Link to post
Share on other sites

Well you were 100% right am2 just doesnt like 1066 ram im sitting here wondering why it wouldnt pass 238fsb tried lowering ht to 800 no difference. So i lower the ram to 667 bam im running 14x244 3.416ghz. So now i gotta keep moving up until it hates on my ram again. I cant afford to get 800 ram for another 2 weeks so im kinda bummed.

 

Update now im at 13x263 im getting close :)

Edited by motoray

Share this post


Link to post
Share on other sites

good for you. you made it past my athlon 64 x2 6400....... How stable is it. I know thats only a 6000 but good god man? A dice run or many is only going to hurt the chip, board and memory. At this point you are getting 400 mah over factory. Honestly once you find the chips peak get the ram at its peak and I'd leave it.

 

I did not mean Milliamp hours MAH

 

Clearly Megahertz is abriviated MHZ.

Edited by boinker

Share this post


Link to post
Share on other sites

Well the amd k8 world record is 4.2somethin so i know it can be done. But the comp is running stable i just cant get too crazy for a couple days while there are these heat spikes in CA its 9:30am and its already 95degreese outside. So its just a matter of hours until my room is HOT.

Share this post


Link to post
Share on other sites

Rads.... are you using water.... Im on air dude. :P Oh well. This chip may end up in another Mobo I have laying around.... I need to get my Dang Phenom II 940 so I can have Another challenge.

Edited by boinker

Share this post


Link to post
Share on other sites

Hey well i can get my fsb to any speed i want now but my processor is being super fickle. I cant even get 3.5 at 1.6v i am wondering if my ram timings are too tight when i get out of what most can do with this processor. 5-5-5-15 I run 3.422 daily 24hr stable but the second i tip over 2.5 BAM unstable. my temps dont cross 44 on load should i consider more volts or just playing with timing??

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×