Zertz Posted September 14, 2008 Posted September 14, 2008 (edited) you are talking about DDR2 right? No, he said he will be going with "DFI LANPARTY LT X48-T3RS" and he wanted input on DDR3 RAM. Edited September 14, 2008 by Zertz Share this post Link to post Share on other sites More sharing options...
smolt Posted September 14, 2008 Posted September 14, 2008 (edited) Looks like a pretty nice rig man....going to be a blast to play on.... sup Doc . yeah should be loads of learning and fun Edited September 14, 2008 by smolt Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted September 14, 2008 Posted September 14, 2008 (edited) For ram smolt, you would be hard pushed to find anything much better than G.Skill 4GB DDR3 PI PC2-12800C7 1600MHz (2x2GB) CAS7 Dual Channel Kit (F3-12800CL7D-4GBPI). Looks like it clocks fairly good as well, not too bad a price for it either (well, for ddr3 anyway ). About time you made the change, you old Luddite Edited September 14, 2008 by kitfit1 Share this post Link to post Share on other sites More sharing options...
Bubbaxm2 Posted September 14, 2008 Posted September 14, 2008 If you go with T3RS and memory with CAS7 you are gonna probably need to update the bios before it will boot up with it. There were some problems with it booting up with cas 7 memory. Might want to grab a stick of cas 8 just in case. I would just stick with the t2r and the flex like you had picked out originally though. No major benefit to switch ing to ddr3. Share this post Link to post Share on other sites More sharing options...
smolt Posted September 25, 2008 Posted September 25, 2008 Ok so far this is the setup DFI LP UT x48T3RS Intel Core 2 Quad Q9550 Yorkfield 2.83GHz 12MB L2 Cache LGA 775 95W Quad-Core Processor 120 extreme black Air cooling 2 Asus 4870X2 2 X OCZ Core Series SATA 11 2.5 Share this post Link to post Share on other sites More sharing options...
smolt Posted September 26, 2008 Posted September 26, 2008 Ok i Need to get ram ordered I need help here Praz OCZ rep How bout some help here ? Share this post Link to post Share on other sites More sharing options...
Praz Posted September 26, 2008 Posted September 26, 2008 I've posted plenty of screenshots with settings at the Club using 1333, 1600 and 2000 speed memory. Should be able to find something that suits your fancy. Share this post Link to post Share on other sites More sharing options...
smolt Posted September 26, 2008 Posted September 26, 2008 thank you Praz Ok i went with the 2 x 2GB OCZ Reaper 1800 Share this post Link to post Share on other sites More sharing options...
bg8780 Posted September 27, 2008 Posted September 27, 2008 (edited) IMO i would look in to what mushkin as to offer. I am extremely happy and impressed with my modules and havent heard anything bad about mushkin. They also have top-notch support. Either their DDR3 looks great as well as their DDR2 modules. Just my two cents These look pretty impressive, however i havent looked in to DDR3 that much, I simply cant afford to lol Edited September 27, 2008 by bg8780 Share this post Link to post Share on other sites More sharing options...
smolt Posted October 4, 2008 Posted October 4, 2008 (edited) Ok update I went with the 2x2gb ocz PC3 14400 (oczrpr18004gk) For ram So far its stable at 3680 and cant seam to get past that My settings as fallows CPU Feature Page Thermal Management Control...........Disabled PPM (EIST) Mode...........................Disabled Limit CPUID MaxVal.........................Disabled CIE Function.................................Disabled Virtualization Technology.................Disabled Core Multi-Processing......................Enabled Main BIOS Page Exist Setup Shutdown......................Mode 2 Shutdown After AC Loss...................Disabled O. C. Fail Retry Counter...................0 CLOCK VC0 Divider..........................Auto CPU Clock Ratio..............................8.5x CPU N/2 Ratio................................Disabled CPU Clock.....................................433 MHz @3680MHz Boot Up Clock................................Auto CPU Clock Amplitude.......................800mV CPU Clock0 Skew............................0ps CPU Clock0 Skew............................0ps DRAM Speed..................................400/1333 PCIE Clock....................................100MHz PCIE Slot Config.............................1X 1X CPU Spread Spectrum.......................Disabled PCIE Spread Spectrum......................Disabled SATA Spread Spectrum.....................Disabled Voltage Setting Page CPU VID Control...............................1.3125V CPU VID Special Add Limit..................Enabled CPU VID Special Add.........................Auto DRAM Voltage Control.......................1.894V SB Core/CPU PLL Voltage...................1.510V NB Core Voltage...............................1.630V CPU VTT Voltage..............................1.325V VCore Droop Control..........................Disabled Clockgen Voltage Control...................3.45V GTL+ Buffers Strength.......................Strong Host Slew Rate................................Weak GTL REF Voltage Control....................Disabled CPU GTL 1/2 REF Volt........................113 CPU GTL 0/3 REF Volt........................100 North Bridge GTL REF Volt .................100 DRAM Timing Page Enhance Data Transmitting.................Fast Enhance Addressing..........................Fast T2 Dispatch....................................Disabl ed Clock Setting Fine Delay....................Listed Below CAS Latency Time (tCL)....................7 RAS# to CAS# Delay (tRCD)...............6 RAS# Precharge (tRP).......................6 Precharge Delay (tRAS).....................24 All Precharge to Act.........................Auto REF to ACT Delay (tRFC)...................Auto Performance Level............................9 Read Delay Phase Adjust...................Listed Below MCH ODT Latency............................Auto Write to PRE Delay (tWR)..................Auto Rank Write to Read (tWTR)................Auto ACT to ACT Delay (tRRD)...................Auto Read to Write Delay (tRDWR)..............Auto Ranks Write to Write (tWRWR)............Auto Ranks Read to Read (tRDRD)...............Auto Ranks Write to Read (tWRRD)..............Auto Read CAS# Precharge (tRTP)..............Auto ALL PRE to Refresh............................Auto Read Delay Phase Adjust Page Channel 1 Phase 0 Pull-In.................Enabled Channel 1 Phase 1 Pull-In.................Enabled Channel 1 Phase 2 Pull-In.................Enabled Channel 1 Phase 3 Pull-In.................Enabled Channel 1 Phase 4 Pull-In.................Enabled Channel 2 Phase 0 Pull-In.................Auto Channel 2 Phase 1 Pull-In.................Auto Channel 2 Phase 2 Pull-In.................Auto Channel 2 Phase 3 Pull-In.................Auto Channel 2 Phase 4 Pull-In.................Auto Clock Setting Fine Delay Page DRAM Clk Driving Strength...................Level 3 DRAM Data Driving Strength.................Level 8 Ch1 DLL Default Skew Model................Model 6 Ch2 DLL Default Skew Model................Model 6 Fine Delay Step Degree....................5ps Ch1 Clock Crossing Setting................Auto DIMM 1 Clock fine delay...................Current DIMM 2 Clock fine delay...................Current DIMM 1 Control fine delay.................Current DIMM 2 Control fine delay.................Current Ch 1 Command fine delay..................Current Ch2 Clock Crossing Setting................Auto DIMM 3 Clock fine delay...................Current DIMM 4 Clock fine delay...................Current DIMM 3 Control fine delay.................Current DIMM 4 Control fine delay.................Current Ch 2 Command fine delay..................Current Ch1Ch2 CommonClock Setting............Auto Any ideas? Edited October 4, 2008 by smolt Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted October 4, 2008 Posted October 4, 2008 Set the "Host Slew Rate" to Strong. Share this post Link to post Share on other sites More sharing options...
smolt Posted October 4, 2008 Posted October 4, 2008 Set the "Host Slew Rate" to Strong. All give it a shot thanks kit Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now