Jump to content

E6850 OC (results)


Recommended Posts

CPU made no difference, GPU did alittle.

 

CSS video stress test:

4.0GHz, Mem 445Mhz (890) 4-4-4-12-1T, 8800GTX @ 648/1026:---FPS=267.39

4.0GHz, Mem 445Mhz (890) 4-4-4-12-1T, 8800GTX @ 600/900:----FPS=256.42

3.0GHz, Mem 333Mhz (666) 4-4-4-12-1T, 8800GTX @ 648/1026:---FPS=268.33

3.0GHz, Mem 333Mhz (666) 4-4-4-12-1T, 8800GTX @ 600/900:----FPS=255.67

LOL - I've barely played with my e6600, and seeing these numbers makes me want to pick up the 6850. I can bench at 3.85, but seeing the magic 4.0 is very tempting :) Off topic - what case are you running. Doesn't look familiar - but it must be roomy to fit twin dual rads - nice. Just curious - thanx.

Share this post


Link to post
Share on other sites

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

LOL - I've barely played with my e6600, and seeing these numbers makes me want to pick up the 6850. I can bench at 3.85, but seeing the magic 4.0 is very tempting :) Off topic - what case are you running. Doesn't look familiar - but it must be roomy to fit twin dual rads - nice. Just curious - thanx.

 

4GHz gave me permagrin :nod:

 

I modded two Cool Master Mystiques. Nothing special but very roomy. It fits my water cooling setup - twin dual rads, a trip rad, 2 pumps, lots of hose, and 11 fans LOL.

 

Dual case mod pictures: The start#1-front, #2-back, somewhat finished #3-front, #4-side. Don't have many pics and my luck with cameras lately has been bad (broke 2 in last 6 months).

 

I'll be getting a P35 soon, test it out with my e6300 on air - just to see. Then I'll see what the e6850 can do, lets hope 4Ghz again (water cooled).

Share this post


Link to post
Share on other sites

  • 2 weeks later...

Keep'n the torch goin, testing my E6850 (L23A047) but switched MB - LP UT P35-T2R (8/23 bios)

 

4050MHz - 9x 450FSB @ 1.525V (bios), Mem @ 450 (DDR901) 4-4-4-12-2T, 8800GTX @ 648/1026

 

Orhtos 10Hr,

3D01, Everest----------------3D03-------------------3D05-------------------3D06

3d01orthors10hr1jb4.th.jpg 3d031ad6.th.jpg 3d051yi9.th.jpg 3d061of4.th.jpg

 

-New CPU-z 1.41, reads correct Vcore (same as bios setting)-

Super PI 32M---------------Super PI 1M

spi32m1wn3.th.jpg spi1m1dq8.th.jpg

Improvement from P5N32-E SLi 680i by 1min.

 

Max Super Pi 32M run: 4203Mhz 9x 467FBS @ 1.525V, DDR935 4-4-4-12-2T

Super PI 32M---------------Super PI 1M

spi32m1av7.th.jpg spi1m1ih0.th.jpg

 

Went for the gusto!

Super PI 32M tweaked run: 4302MHZ 9x 478FSB @ 1.6V, DDR957 4-4-4-9-2T

Super PI 32M---------------Super PI 1M

spi32mt44491jy5.th.jpg spi1mt44491mt6.th.jpg

 

Sped up the RAM! My fastest PI times :D

Super PI 32M tweaked run: 4302MHz 9x 478FSB @ 1.6V, DDR1146 5-5-5-9-2T

Super PI 32M---------------Super PI 1M

spi32mt55591jf6.th.jpg spi1mt55591or3.th.jpg

 

These were some fairly easy benchies to achieve. Most secondary timings are in auto/default, except for EDT(fast), EA(fast), tRFC (42-46). I messed with the voltage mostly. Now only if I could get 4.1G stable Y:eek2:Y Here's a CPU-z validation @ 4311MHz 9x 479FSB, the highest I could get with Vcore 1.6V.

Share this post


Link to post
Share on other sites

  • 2 months later...
@Taowulf You comparing to an AMD, Intel C2D are fast :nod:. What's your MB & RAM...settings?

 

My P35 is a little slow, 14.xxxs 1M - 13m21.xxxs 32M super pi @ 3.6 GHz DDR-1234 MHz :(

 

Well, it is in pieces at the moment, I was prepping to drill tomorrow (damn it got late on me) and I just got my "old" system up on Ubuntu 7.10 64bit. had a few issues due to Ubuntu not liking the ACPI on my NF590. Oh, and a bad DVD-R. I have a dust problem in my house, the Plextor drive I have had for about 3 years finally gave up the ghost.

 

I was also very tired and not thinking straight when I read this last night. Or yesterday...whenever it was. I was reading seconds as minutes and things were just not going together in my head correctly.

 

I am running something like 9x400. Timings on the mem are OCZ recommended at 4-5-4-15. Can't remember voltages at the second, I might have left them where they were when I was trying 3.7Ghz. Temps were a wee bit high so i backed off. No need to push it until i have the watercooling set up.

 

Anyway, I have been up far too long. I need sleep so I can handle the drill safely tomorrow....after this BSG repeat is over. Razor is on tomorrow, I have to get in the right frame of mind.

Share this post


Link to post
Share on other sites

  • 3 weeks later...

I was testing 4.151Ghz, 1.656 (CPUz and Speedfan reported, actually set to 1.6375 in BIOS)

 

4.2 and higher were getting me into the 1.7v range, and the temps were gettign silly.

 

Made it 20 minutes into Orthos and started exceeding 75C, so I am backing off for now.

 

Once I rerun the cooling loop (need to clean up a few spots) and go to distilled water instead of this PC Chill that Danger Den tossed in for free, I might try it again.

Share this post


Link to post
Share on other sites

I was testing 4.151Ghz, 1.656 (CPUz and Speedfan reported, actually set to 1.6375 in BIOS)

 

4.2 and higher were getting me into the 1.7v range, and the temps were gettign silly.

 

Made it 20 minutes into Orthos and started exceeding 75C, so I am backing off for now.

 

Once I rerun the cooling loop (need to clean up a few spots) and go to distilled water instead of this PC Chill that Danger Den tossed in for free, I might try it again.

 

Look'n good, you could post some results. SuperPi is a fun test, hehe.

 

So the PC Chiller is no good? DD pitched in a bottle on an order I made.

Share this post


Link to post
Share on other sites

Look'n good, you could post some results. SuperPi is a fun test, hehe.

 

So the PC Chiller is no good? DD pitched in a bottle on an order I made.

 

Not impressed with it yet. I seriously doubt I will get worse results with distilled water/biocide.

 

I don't want fancy colors anyway.

 

I will be back in a bit with a superPI run. I have done one at 4.2, but forgot to take a screenshot.

Share this post


Link to post
Share on other sites

The timings I am at are pretty much it. If I drop down to closer to 800, I can go to 4-5-4-15 19, but testing leads me to believe that where I am now is as good as it is going to get.

 

I was actually able to test clean in Memtest at 5-5-5-10 at 950Mhz, but Orthos and everything else didn't like it too much.

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now

×
×
  • Create New...