pont Posted April 11, 2007 Posted April 11, 2007 http://valid.x86-secret.com/show_oc?id=185709 i think thats a ok oc but im sure you guys will let me know ram is at 3.4.4.8 .1t im knot really sure what eles to do to make it a better or more stable oc so any thing you guys can do to help would be very helpful ............. .thanks Share this post Link to post Share on other sites More sharing options...
THEnumber337 Posted April 11, 2007 Posted April 11, 2007 http://valid.x86-secret.com/show_oc?id=185709 i think thats a ok oc but im sure you guys will let me know ram is at 3.4.4.8 .1t im knot really sure what eles to do to make it a better or more stable oc so any thing you guys can do to help would be very helpful ............. .thanks Nice, now make an OCDB entry. Share this post Link to post Share on other sites More sharing options...
pont Posted April 11, 2007 Posted April 11, 2007 how do i do that ?? Share this post Link to post Share on other sites More sharing options...
THEnumber337 Posted April 11, 2007 Posted April 11, 2007 how do i do that ?? Go here and read all the rules and requirements. Share this post Link to post Share on other sites More sharing options...
Kingfisher Posted April 11, 2007 Posted April 11, 2007 Welcome to the Street. We have a section dedicated to all of our screenshots and settings called the Overclock data base or OCDB. You are more than welcome to participate as THEnumber337 provided linkage. Share this post Link to post Share on other sites More sharing options...
pont Posted April 11, 2007 Posted April 11, 2007 well i tryed ocdb but it failed ..it will pass at 2.9 but that is not 3.0 is it...dam i thought i had something here thanks for the help i really do take what you guys say and use it but this time my hard ware must not be up to it .. maybe afer a little reading on how to use the dividers and all i might get to 3.0 or higher..thanks again guys Share this post Link to post Share on other sites More sharing options...
Clay Posted April 11, 2007 Posted April 11, 2007 @Pont: Welcome..... Did ya' happen to get a look at the stepping and date,before ya' plugged er' in? Also I was kinda' wondering what voltage you were needing for 2.9ghz. The reason I'm asking is I just bought an XP4000 LCBBE 0643SPMW And I'm kinda' looking for data on it. So as I can decide what to do with it. Share this post Link to post Share on other sites More sharing options...
thejamesvolta Posted April 11, 2007 Posted April 11, 2007 Yeah, I was curious about the voltage too. Also, I would drop your HT multiplier to 4x instead of 5x, that might help cure some issues with stability. Nice OC though man!!!!! Have you checked out the overclocking guide yet? I found this to be the MOST resourceful piece of information when it comes to learning you stuff. Share this post Link to post Share on other sites More sharing options...
pont Posted April 11, 2007 Posted April 11, 2007 hi guys no i didnt get the steppings when i installed the chip .but i will when i install my new water block ..and as for the volts i havent change any thing so i guess there at stock settings for both the vcore and ram Share this post Link to post Share on other sites More sharing options...
thejamesvolta Posted April 11, 2007 Posted April 11, 2007 Stock!!! You could probably get some better stability if you bumped up the vcore a bit. You could probably also get a higher clock. Share this post Link to post Share on other sites More sharing options...
Clay Posted April 11, 2007 Posted April 11, 2007 Stock!!!! LOL...(ditto lol) It's probably a really good idea to do some reading in the overclockers guide especially concerning voltages and the +percents. Once inna' while someone cooks a proceesor. That's a very nice processor.. Share this post Link to post Share on other sites More sharing options...
pont Posted April 15, 2007 Posted April 15, 2007 what do you guys think of the exos system to cool my rig? im only cooling the chip and dont really plan to do much eles i got a line on one for 75 bucks so im kind of leaning that way any help???? Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now