OsamaBinAthlon+ Posted March 18, 2007 Posted March 18, 2007 http://www.arcticsilver.com/arcticlean.htm Does it work? Sometimes it takes a long butt time with a credit card and some alcohol to get the paste off of stock sinks and stuff. Share this post Link to post Share on other sites More sharing options...
nutxo Posted March 18, 2007 Posted March 18, 2007 I use a dab of bleach and then clean with alcohol. It works very well and I can do 9000 cpus for a buck. Share this post Link to post Share on other sites More sharing options...
OsamaBinAthlon+ Posted March 18, 2007 Posted March 18, 2007 like put some bleach on a qtip? Share this post Link to post Share on other sites More sharing options...
Voltes-5 Posted March 18, 2007 Posted March 18, 2007 It does work. Been using it for months now and always get a clean surface. What I do is that I take off the majority of the tim with a cotton swab like qtips then use the #1 and soak up the rest, sometimes I do it twice till I get a clean surface by checking the swab stick if its clean which means the surface is clean. Then use the #2 for final cleaning. Share this post Link to post Share on other sites More sharing options...
ooeric Posted March 18, 2007 Posted March 18, 2007 um... paper towel the entire thing.. jeez then just use some GOO GONE. which is cheap but works. or just use some alcohol . aagain with paper towel. and its clean you can never get any surface 100% clean. so forget what people say. unless maybe you wanna build a clean room in your house.. Share this post Link to post Share on other sites More sharing options...
Peanut2001 Posted March 18, 2007 Posted March 18, 2007 Wipe it clean with a paper towel then go back over it with a paper towel moistened with acetone(available at walmart and paint stores). If acetone wont get it off, there isnt much else that will that is safe to use lol. Share this post Link to post Share on other sites More sharing options...
momoceio Posted March 18, 2007 Posted March 18, 2007 It does work better than alcohol...but not sure it's worth spending $5 for Share this post Link to post Share on other sites More sharing options...
godlyatheist Posted March 18, 2007 Posted March 18, 2007 just buy it from microcenter or local shop to save shipping. use credit card to scrap off most of the TIM and use #1, wait 30 sec, wipe it off, use #2 and you have shinny proc:D i wouldn't try acetone cause it'll eat away the PCB of your mobo and the plastic part of your proc. Share this post Link to post Share on other sites More sharing options...
Peanut2001 Posted March 18, 2007 Posted March 18, 2007 The key word there was moistened, not soaked. I've always used acetone and never had any problems. I just don't let it touch anything except what I want to clean. Share this post Link to post Share on other sites More sharing options...
3stars Posted March 18, 2007 Posted March 18, 2007 Acetone wont eat your pcb well it might if you dip the board in it. then use alcohol, vodka for me and hospitol swabs for the puter Share this post Link to post Share on other sites More sharing options...
red930 Posted March 18, 2007 Posted March 18, 2007 Isopropyl Alcohol at 90% or greater is the only cleaner I've ever needed. Goo Gone and any other product with citrus or petroleum products is not recommended since the oils will penetrate into the surface defects and block the TIM from doing its job. Acetone can be used but care must be taken to only apply it to the metal surfaces. Acetone can and will soften the adhesive used to keep the IHS attached to the processor mount. Share this post Link to post Share on other sites More sharing options...
momoceio Posted March 18, 2007 Posted March 18, 2007 You can use goo gone as long as you cleanup with alcohol to remove and oily residue. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now