Protius Posted December 26, 2006 Posted December 26, 2006 I got 2 of these http://www.newegg.com/Product/Product.asp?...N82E16820220057 but for some reason i can't get all 4 sticks stable, i've tried loosening timings to 3-4-4-8 and messing with voltage, any thoughts on the settings i should use? update-tried just 2 sticks still no stable, i have everything on stock and it still randomly freezes and reboots Share this post Link to post Share on other sites More sharing options...
allston Posted December 26, 2006 Posted December 26, 2006 have you tried a 2T command rate, it might help Share this post Link to post Share on other sites More sharing options...
k€lticknight Posted December 26, 2006 Posted December 26, 2006 did you use 2 +4 slots[orange],works better this mobo dont like 4 sticks most i got to work stable was 3x512 sticks,but not 4 sticks ,so got 2x1gb sticks Share this post Link to post Share on other sites More sharing options...
Final8ty Posted December 27, 2006 Posted December 27, 2006 did you use 2 +4 slots[orange],works betterthis mobo dont like 4 sticks most i got to work stable was 3x512 sticks,but not 4 sticks ,so got 2x1gb sticks 4 sticks of what i have worked fine. Share this post Link to post Share on other sites More sharing options...
Simon D Posted December 27, 2006 Posted December 27, 2006 I have four sticks, I found that I could not run at DDR400 few stability problem. This was solved when I drop to DDR333 using a memory divider, change a few other setting as well (voltages) My Setting for DFI LanParty UT CFX3200 for ballistix memory and CPU X2 4400 FSB Bus Frequency: 266 LDT/FSB Frequency Ratio: 5x CPU/FSB Frequency Ratio: 10x RD580 HT PLL Speed: Auto HT Bus NMOS Drive Strength: 5 HT Bus PMOS Drive Strength: 5 HT Bus Receiver Impendence: 10 CPU HT Bus Drive Strength: Normal K8 Cool & Quiet Support: Disabled CPU VID Control: 1.4v CPU VID Special Control: 110% DRAM Voltage Control: 2.70v SB PCIE Voltage: 1.8v NB Analogue Voltage: 1.34v LDT Bus Voltage: 1.34v NB Core Voltage: 1.34v DRAM Frequency Set: 133 = RAM/FSB:05/06 CPC: Auto CAS (Tcl): 2.5 Trcd: 3 Tras: 7 Trp: 3 Trc: 10 Trfc: 12 Trrd: 3 Twr: 3 Twtr: 2 Trwt: 3 Tref: 3120 Bank Interleaved: Enabled Errata 94: Disabled Errata 123: AUTO Odd Divisor Correct: Disabled DQS Skew Control: Auto DQS Skew Value: N/A DRAM Drive Strength: Auto DRAM Data Drive Strength: Auto DIMM 1/2 Clock Timing Skew: Auto DIMM 3/4 Clock Timing Skew: Auto Max Async Latency: 8ns Read Preamble Time: 6ns IdleCycle Limit: 128clks Dynamic Counter: Disabled R/W Queue Bypass: 16x Bypass Max: 4x Burst Length: 4 The TXCLK Gating and PCIE Common Clock are normally disabled by default; I found an increase in video performance setting these 2 to enable Set the 2 GFX slot power limits to 130W, and enabled 10% extra current to the GFX slots, I found this helped with card overclocking also. I hope this help you Share this post Link to post Share on other sites More sharing options...
Final8ty Posted December 27, 2006 Posted December 27, 2006 DRAM Drive Strength: should be at least 20 for 4 sticks. I'm up to DDR510 255FSB 2.5-3-2-5 4 sticks. Share this post Link to post Share on other sites More sharing options...
k€lticknight Posted December 27, 2006 Posted December 27, 2006 4 sticks of what i have worked fine. was meant for protius Share this post Link to post Share on other sites More sharing options...
Protius Posted December 27, 2006 Posted December 27, 2006 I have four sticks, I found that I could not run at DDR400 few stability problem. This was solved when I drop to DDR333 using a memory divider, change a few other setting as well (voltages) My Setting for DFI LanParty UT CFX3200 for ballistix memory and CPU X2 4400 FSB Bus Frequency: 266 LDT/FSB Frequency Ratio: 5x CPU/FSB Frequency Ratio: 10x RD580 HT PLL Speed: Auto HT Bus NMOS Drive Strength: 5 HT Bus PMOS Drive Strength: 5 HT Bus Receiver Impendence: 10 CPU HT Bus Drive Strength: Normal K8 Cool & Quiet Support: Disabled CPU VID Control: 1.4v CPU VID Special Control: 110% DRAM Voltage Control: 2.70v SB PCIE Voltage: 1.8v NB Analogue Voltage: 1.34v LDT Bus Voltage: 1.34v NB Core Voltage: 1.34v DRAM Frequency Set: 133 = RAM/FSB:05/06 CPC: Auto CAS (Tcl): 2.5 Trcd: 3 Tras: 7 Trp: 3 Trc: 10 Trfc: 12 Trrd: 3 Twr: 3 Twtr: 2 Trwt: 3 Tref: 3120 Bank Interleaved: Enabled Errata 94: Disabled Errata 123: AUTO Odd Divisor Correct: Disabled DQS Skew Control: Auto DQS Skew Value: N/A DRAM Drive Strength: Auto DRAM Data Drive Strength: Auto DIMM 1/2 Clock Timing Skew: Auto DIMM 3/4 Clock Timing Skew: Auto Max Async Latency: 8ns Read Preamble Time: 6ns IdleCycle Limit: 128clks Dynamic Counter: Disabled R/W Queue Bypass: 16x Bypass Max: 4x Burst Length: 4 The TXCLK Gating and PCIE Common Clock are normally disabled by default; I found an increase in video performance setting these 2 to enable Set the 2 GFX slot power limits to 130W, and enabled 10% extra current to the GFX slots, I found this helped with card overclocking also. I hope this help you i've been using these mem settings and they seem to be working, hasn't crashed for 24 hours which is good for me, i'll be runing prime95 and memtest to check ps-thanks the help Share this post Link to post Share on other sites More sharing options...
ComicDom1 Posted December 27, 2006 Posted December 27, 2006 I have four sticks, I found that I could not run at DDR400 few stability problem. This was solved when I drop to DDR333 using a memory divider, change a few other setting as well (voltages) My Setting for DFI LanParty UT CFX3200 for ballistix memory and CPU X2 4400 FSB Bus Frequency: 266 LDT/FSB Frequency Ratio: 5x CPU/FSB Frequency Ratio: 10x RD580 HT PLL Speed: Auto HT Bus NMOS Drive Strength: 5 HT Bus PMOS Drive Strength: 5 HT Bus Receiver Impendence: 10 CPU HT Bus Drive Strength: Normal K8 Cool & Quiet Support: Disabled CPU VID Control: 1.4v CPU VID Special Control: 110% DRAM Voltage Control: 2.70v SB PCIE Voltage: 1.8v NB Analogue Voltage: 1.34v LDT Bus Voltage: 1.34v NB Core Voltage: 1.34v DRAM Frequency Set: 133 = RAM/FSB:05/06 CPC: Auto CAS (Tcl): 2.5 Trcd: 3 Tras: 7 Trp: 3 Trc: 10 Trfc: 12 Trrd: 3 Twr: 3 Twtr: 2 Trwt: 3 Tref: 3120 Bank Interleaved: Enabled Errata 94: Disabled Errata 123: AUTO Odd Divisor Correct: Disabled DQS Skew Control: Auto DQS Skew Value: N/A DRAM Drive Strength: Auto DRAM Data Drive Strength: Auto DIMM 1/2 Clock Timing Skew: Auto DIMM 3/4 Clock Timing Skew: Auto Max Async Latency: 8ns Read Preamble Time: 6ns IdleCycle Limit: 128clks Dynamic Counter: Disabled R/W Queue Bypass: 16x Bypass Max: 4x Burst Length: 4 The TXCLK Gating and PCIE Common Clock are normally disabled by default; I found an increase in video performance setting these 2 to enable Set the 2 GFX slot power limits to 130W, and enabled 10% extra current to the GFX slots, I found this helped with card overclocking also. I hope this help you I think it says in the manual, that when you run four sticks of memory the speed does drop to 333. Of course there might be some exceptions to this. Jason Share this post Link to post Share on other sites More sharing options...
theycallmeMR Posted December 27, 2006 Posted December 27, 2006 after recently reading manual it states that four double sided sticks drop bk to 2t and 333 mhz where 4x single sided sticks stay @1t and 400 mhz wierd i know i cant get my 2x 512 mb sticks to run at stock either it just freezes on desktop or the final windows loading screen and simple programs use 100 % cpu when idle Share this post Link to post Share on other sites More sharing options...
Protius Posted December 27, 2006 Posted December 27, 2006 It randomly restarted again the settings i'm using are FSB Bus Frequency: 300 LDT/FSB Frequency Ratio: 3x CPU/FSB Frequency Ratio: 9x RD580 HT PLL Speed: Auto HT Bus NMOS Drive Strength: 20 HT Bus PMOS Drive Strength: 20 HT Bus Receiver Impendence: 10 CPU HT Bus Drive Strength: Normal K8 Cool & Quiet Support: Disabled CPU VID Control: 1.45v CPU VID Special Control: 103% DRAM Voltage Control: 2.70v SB PCIE Voltage: 1.8v NB Analogue Voltage: 1.34v LDT Bus Voltage: 1.34v NB Core Voltage: 1.34v DRAM Frequency Set: 133 = RAM/FSB:05/06 CPC: disabled CAS (Tcl): 2.5 Trcd: 3 Tras: 7 Trp: 3 Trc: 10 Trfc: 12 Trrd: 3 Twr: 3 Twtr: 2 Trwt: 3 Tref: 3120 Bank Interleaved: Enabled Errata 94: Disabled Errata 123: AUTO Odd Divisor Correct: Disabled DQS Skew Control: Auto DQS Skew Value: N/A DRAM Drive Strength: Auto DRAM Data Drive Strength: Auto DIMM 1/2 Clock Timing Skew: Auto DIMM 3/4 Clock Timing Skew: Auto Max Async Latency: 8ns Read Preamble Time: 6ns IdleCycle Limit: 128clks Dynamic Counter: Disabled R/W Queue Bypass: 16x Bypass Max: 4x Burst Length: 4 Share this post Link to post Share on other sites More sharing options...
Final8ty Posted December 28, 2006 Posted December 28, 2006 was meant for protius So was mine Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now