Jump to content
Sign in to follow this  
Khanal

Cannot install OS help a noob out please :(

Recommended Posts

Hi guys

I recently assembled my system and having done one or two builds in the past everythings gone smoothly however

 

I boot my system up ready to install the OS and it gives me an error I can get to the stage where it says its loading the windows drivers after that it says windows is loading setup and it freezes then gives me an error something like "PAGE FAULT IN NON PAGED AREA" then there are other times where it comes up with another blue screen that says something like "error in .sif file"

 

I'm a bit of a noob when it comes to DFI so please have patience with me

please help all I want to do is get up and running :(

 

Thanks for any response

Khanal,

Share this post


Link to post
Share on other sites

Hello,

 

You must test the memory with memtest before installing windows.

Do you know how to do this?

 

- Enter the bios and go to Genie settings.

- Scroll down a bit and look for enable memtest86+.

- Then save and exit.

 

Now it should boot into memtest.

Let the program run for at least 3 hours.

 

If you get any errors instantly stop and try one stick at a time in the top orange slot.

 

Any errors, increase the memory voltage to 2.7v.

 

Still errors, it might be faulty or the memory timings need adjusting.

 

If it is Samsung original, look on the memory chips, does it say UCCC?

Share this post


Link to post
Share on other sites

wow thanks alot for the warm welcome guys :)

 

Ok I'll try memtest first will post back and let u guys know what i get.:D

Share this post


Link to post
Share on other sites

hi guys I decided to use one stick in the orange dimm slot closest to the edge of the mobo

I ran memtest while i was away at work (I work nights) only to come home to find it had crashed at 7 minutes something about "enexpected interrupt alting" so im running it again with optimised defaults in the bios setting its now crashed at 13min 58secs with 545911 errors lol.

 

Also something else I noticed is when I ask to boot from cdrom and it says press any key to boot it gives me an error message saying NTLDR is missing please press ctrl+alt+del to restart.

 

i have heat spreaders on the ram that i stuck on but i managed to remove them and check whats on the ram chips it says

 

SAMSUNG 613 K4H510438D-TCCC

 

VCH650CC KOREA

 

is that any help to anyone? thanks I look forward to any response :)

Share this post


Link to post
Share on other sites

Ok same thing on test 5 coming in with 120,000 errors going up like a speed clock im guessing its going to give me the same amount of errors as the first stick.

Share this post


Link to post
Share on other sites

ok its stopped with the message "unexpected interrupt-halting" with 207697 errors

 

Do you think its a memory issue? shall I buy some new ram?

Share this post


Link to post
Share on other sites
Guest erico
ok its stopped with the message "unexpected interrupt-halting" with 207697 errors

 

Do you think its a memory issue? shall I buy some new ram?

RMA is so much less bank account damaging!:)

try contacting the vendors or the manufacturers website

Share this post


Link to post
Share on other sites

Both sticks erroring like this generally means that they just aren't configured right - not that you have 2 bad sticks. Are you attempting to run everthing on Auto? If so, you'll probably have to get hold of some stable settings for your TCCC (any brand will do) and use those. These are generally 3-4-4-8 sticks @1T - so your settings will likely look similar to:

 

DRAM Frequency Set............................  -  200=RAM/FSB:01/01
Command Per Clock (CPC).......................  -  Enable
CAS Latency Control (Tcl).....................  -  3.0
RAS# to CAS# delay (Trcd).....................  -  04 Bus Clocks
Min RAS# active time (Tras)...................  -  08 Bus Clocks
Row precharge time (Trp)......................  -  04 Bus Clocks
Row Cycle time (Trc)..........................  -  07 Bus Clocks (maybe higher)
Row refresh cyc time (Trfc)...................  -  14 Bus Clocks (maybe higher)
Row to Row delay (Trrd).......................  -  02 Bus Clocks
Write recovery time (Twr).....................  -  02 Bus Clocks
Write to Read delay (Twtr)....................  -  02 Bus Clocks
Read to Write delay (Trwt)....................  -  03 Bus Clocks
Refresh Period (Tref).........................  -  3120 Cycles
DRAM Bank Interleave..........................  -  Enabled

DQS Skew Control..............................  -  Auto
DQS Skew Value................................  -  0
DRAM Drive Strength...........................  -  Auto
DRAM Data Drive Strength......................  -  Auto
Max Async Latency.............................  -  Auto
DRAM Response Time............................  -  Normal
Read Preamble Time............................  -  Auto
IdleCycle Limit...............................  -  256 Cycles
Dynamic Counter...............................  -  Disable
R/W Queue Bypass..............................  -  16 x
Bypass Max....................................  -  07 x
32 Byte Granularity...........................  -  Disable(8 Bursts)

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...