Praz Posted August 28, 2007 Posted August 28, 2007 DFI LanParty UT P35-T2R(LGA 775) BIOS 08/10 Intel Core 2 Extreme X6800 Conroe 2.93GHz / 4M L2 core) OCZ DDR2 PC2-9200 Reaper HPC Edition 2GB (2 x 1GB) DDR2 1150 OCZ2RPR11502GK XFX PVT80FSHF9 GeForce 8800GTX 768MB, 158.22 drivers 684/1050 HITACHI SATA II 8MB cache 80GB hdd SAMSUNG 18X SATA DVD Burner With LightScribe SILVERSTONE ST85ZF ATX12V / EPS12V 850W SLI Certified Power Supply D-tek FuZion CPU Water Block Stock onboard chipset cooling - Heatpipe * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] Exist Setup Shutdown........... - Mode 1 CLOCK VC0 divider.............. - AUTO CPU Clock Ratio Unlock......... - Enabled CPU Clock Ratio................ - 7x CPU Clock...................... - 530MHz Boot Up Clock.................. - Auto DRAM Speed..................... - 333/667 PCIE Clock..................... - 100MHz PCIE Slot Config............... - 1X 1X CPU Spread Spectrum............ - Disabled PCIE Spread Spectrum........... - Disabled SATA Spread Spectrum........... - Disabled [/color] [b]CPU Feature:[/b] [color=red] Thermal Management Control..... - Disabled PPM(EIST) Mode................. - Disabled Limit CPUID MaxVal............. - Disabled CIE Function................... - Disabled Execute Disable Bit............ - Disabled Virtualization Technology...... - Disabled Core Multi-Processing.......... - Enabled [/color] [b]Voltage Settings:[/b] [color=red] CPU VID Control................ - 1.48750V CPU VID Special Add............ - Auto DRAM Voltage Control........... - 2.310V SB 1.05V Voltage............... - 1.070V SB Core/CPU PLL Voltage........ - 1.55V NB Core Voltage................ - 1.33V CPU VTT Voltage................ - 1.20V Vcore Droop Control............ - Enabled Clockgen Voltage Control....... - 3.45V GTL+ Buffers Strength.......... - Strong Host Slew Rate................. - Weak GTL REF Voltage Control........ - Disable x CPU GTL1/3 REF Volt.......... - 110 x CPU GTL 0/2 REF Volt......... - 110 x North Bridge GTL REF Volt.... - 110 [/color] [b]DRAM Timing:[/b] [color=red] Enhance Data transmitting...... - AUTO Enhance Addressing............. - AUTO Channel 1 CLK fine delay....... - AUTO - Current[13] Channel 2 CLK fine delay....... - AUTO - Current[12] CAS Latency Time (tCL)......... - 5 RAS# to CAS# Delay (tRCD)...... - 5 RAS# Precharge (tRP)........... - 5 Precharge Delay (tRAS)......... - 15 All Precharge to Act........... - AUTO REF to ACT Delay (tRFC)........ - AUTO Performance Level.............. - AUTO MCH ODT Latency................ - AUTO Write to PRE Delay (tWR)....... - AUTO Rank Write to Read (tWTR)...... - AUTO ACT to ACT Delay (tRRD)........ - AUTO Read to Write Delay (tRDWR).... - AUTO Ranks Write to Write (tWRWR)... - AUTO Ranks Read to Read (tRDRD)..... - AUTO Ranks Write to Read (tWRRD).... - AUTO Read CAS# Precharge (tRTP)..... - AUTO ALL PRE to Refresh............. - AUTO [/color] ========== Orthos (SP2004) + 3dMark2001SE + 4x CPU-Z + MemSet: 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: ========== short description: 530x7@ 3710mhz 1.4875vcore / 2.31vdimm 5.0-5-5-15 1060MHz Share this post Link to post Share on other sites More sharing options...
CharmedLover84 Posted September 7, 2007 Posted September 7, 2007 EVGA 122-CK-NF68-A2 SLI, P30 (7/11/07) BIOS Mushkin 4GB (2x2GB) XP2-8500 DDR2-1066 (PC2-8500) (Model# 996562) Intel Core 2 Extreme QX6850 Kentsfield (G0 Stepping) 2x eVGA 8800GTX 768MB 384-Bit 16x PCI-E 162.18 drivers @ 621/972 Western Digital Caviar WD3200YS 320GB 7200 RPM 16MB Cache SATA 3.0Gb/s Plextor 18x SATA DVD+/-RW Dual Layer Burner Fortron Everest 1010W Power Supply D5 Pump + Danger Den TDX775 + Danger Den Black Ice XtremeIII Radiator ========== [b]FSB & Memory Config[/b] CPU Freq, Mhz....................... - 3666.6 CPU Multiplier...................... - 9x FSB - Memory Clock Mode............. - Unlinked FSB - Memory Ratio ................. - Auto FSB - QDR (Mhz)..................... - 1628 MEM (DDR), Mhz...................... - 889 [b]Memory Timing Setting[/b] Memopry Timing Setting.............. - Expert tCL (CAS Latency)................... - 5 tRCD................................ - 5 tRP................................. - 5 tRAS................................ - 18 Command Per Clock (CMD)............. - 2T tRRD................................ - 4 tRC................................. - 27 tWR................................. - 5 tWTR................................ - 10 tREF................................ - Auto (7.8uS) [b]System Clocks[/b] CPU Multiplier...................... - 9x PCIe x16_1 (Mhz).................... - 105MHz PCIe x16_3 (Mhz).................... - 100 PCIe x16_2 (Mhz).................... - 105 nForce SPP --> nForce MCP........... - 5 nForce SPP <-- nForce MCP........... - 5 [b]System Voltages[/b] CPU Core............................ - 1.5v CPU FSB............................. - 1.5v Memory.............................. - 2.1V nForce SPP.......................... - 1.45v nForce MCP.......................... - 1.550v HT nForce SPP <-> MCP............... - 1.4v ========== Quad Prime95 (V25.3), 2x CPU-Z, 3dMark2001SE: 69493 3dMark2003: 64930 3dMark2005: 23732 3dMark2006: 18562 Short description: 407x9 @ 3.666Ghz @ 1.5V 5-5-5-18-2T @ 2.1V Share this post Link to post Share on other sites More sharing options...
Chump Posted September 8, 2007 Posted September 8, 2007 DFI LANPARTY UT P35-T2R (BIOS 1019) INTEL CORE 2 DUO QUAD Q6600 KENTSFIELD 2.4GHZ 4M L2 CACHE OCZ PC2-8500 SLI 2 x 1GB PN:OCZN1066SR2GK INNO3D 8800GTS 320MB (163.71 DRIVERS OVERCLOCK 617 X 955) 4 X HITACHI DJ 80GB HD'S (RAID 0 / 64K STRIPE) SONY DUAL LAYER DVD RW (DRU-820A) OCZ GAMEXTREAM 1010W PSU WINDOWS XP PRO SP2 CPU COOLING: D-TEK FUSION + PA130.3 + D5 VARIO [B]>CPU Feature:[/B] [COLOR=red]Thermal Management Control.......... - Disabled[/COLOR] [COLOR=red]PPM(EIST) Mode...................... - Disabled[/COLOR] [COLOR=red]Limit CPUID MaxVal.................. - Disabled[/COLOR] [COLOR=red]CIE Function........................ - Disabled[/COLOR] [COLOR=red]Execute Disable Bit................. - Disabled[/COLOR] [COLOR=red]Virtualization Technology........... - Disabled[/COLOR] [COLOR=red]Core Multi-Processing............... - Enabled[/COLOR] [B]>DRAM Timing:[/B] [COLOR=red]Enhance Data transmitting........... - Fast[/COLOR] [COLOR=red]Enhance Addressing.................. - Fast[/COLOR] [COLOR=red]T2 Dispatch......................... - Disabled[/COLOR] [B]>Clock Setting Fine Delay Press Enter:[/B] [COLOR=blue]Ch1 Clock Crossing Setting......... - More Aggressive[/COLOR] [COLOR=blue]DIMM1 Clock Fine Delay............. - Current[TBC][/COLOR] [COLOR=blue]DIMM2 Clock Fine Delay............. - Current[TBC][/COLOR] [COLOR=blue]Ch1 ControlFine Delay.............. - Current[TBC][/COLOR] [COLOR=blue]Ch1 ControlFine Delay.............. - Current[TBC][/COLOR] [COLOR=blue]Ch2 Clock Crossing Setting......... - More Aggressive[/COLOR] [COLOR=blue]DIMM3 Clock Fine Delay............. - Current[TBC][/COLOR] [COLOR=blue]DIMM4 Clock Fine Delay............. - Current[TBC][/COLOR] [COLOR=blue]Ch2 ControlFine Delay.............. - Current[TBC][/COLOR] [COLOR=blue]Ch2 ControlFine Delay.............. - Current[TBC][/COLOR] [COLOR=blue]Ch1 Ch2 Common Clock Setting....... - More Aggressive[/COLOR] [COLOR=blue]Ch1 RDCAS GNT-Chip Delay........... - Auto[/COLOR] [COLOR=blue]Ch1 WRCAS GNT-Chip Delay........... - Auto[/COLOR] [COLOR=blue]Ch1 Command To CS Delay............ - Auto[/COLOR] [COLOR=blue]Ch2 RDCAS GNT-Chip Delay........... - Auto[/COLOR] [COLOR=blue]Ch2 WRCAS GNT-Chip Delay........... - Auto[/COLOR] [COLOR=blue]Ch2 Command To CS Delay............ - Auto[/COLOR] [COLOR=red]CAS Latency Time (tCL).............. - 5[/COLOR] [COLOR=red]RAS# to CAS# Delay (tRCD)........... - 5[/COLOR] [COLOR=red]RAS# Precharge (tRP)................ - 5[/COLOR] [COLOR=red]Precharge Delay (tRAS).............. - 10[/COLOR] [COLOR=red]All Precharge to Act................ - 5[/COLOR] [COLOR=red]REF to ACT Delay (tRFC)............. - 26[/COLOR] [COLOR=red]Performance Level................... - 6[/COLOR] [B]>Read delay phase adjust Press Enter:[/B] [COLOR=blue]Channel 1 Phase 0 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 1 Phase 1 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 1 Phase 2 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 1 Phase 3 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 1 Phase 4 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 0 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 1 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 2 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 3 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 4 Pull-In.......... - Auto[/COLOR] [COLOR=red]MCH ODT Latency..................... - Auto[/COLOR] [COLOR=red]Write to PRE Delay (tWR)............ - 14[/COLOR] [COLOR=red]Rank Write to Read (tWTR)........... - 11[/COLOR] [COLOR=red]ACT to ACT Delay (tRRD)............. - 3[/COLOR] [COLOR=red]Read to Write Delay (tRDWR)......... - 8[/COLOR] [COLOR=red]Ranks Write to Write (tWRWR)........ - Auto[/COLOR] [COLOR=red]Ranks Read to Read (tRDRD).......... - Auto[/COLOR] [COLOR=red]Ranks Write to Read (tWRRD)......... - Auto[/COLOR] [COLOR=red]Read CAS# Precharge (tRTP).......... - 4[/COLOR] [COLOR=red]ALL PRE to Refresh.................. - 5[/COLOR] [B]>Voltage Settings:[/B] [COLOR=red]CPU VID Control..................... - 1.52500v[/COLOR] [COLOR=red]CPU VID Special Add................. - Auto[/COLOR] [COLOR=red]DRAM Voltage Control................ - 2.27v[/COLOR] [COLOR=red]SB 1.05V Voltage.................... - 1.070v[/COLOR] [COLOR=red]SB Core/CPU PLL Voltage............. - 1.55v[/COLOR] [COLOR=red]NB Core Voltage..................... - 1.61v[/COLOR] [COLOR=red]CPU VTT Voltage..................... - 1.60v[/COLOR] [COLOR=red]Vcore Droop Control................. - Disabled[/COLOR] [COLOR=red]Clockgen Voltage Control............ - 3.45v[/COLOR] [COLOR=red]GTL+ Buffers Strength............... - Weak[/COLOR] [COLOR=red]Host Slew Rate...................... - Weak[/COLOR] [COLOR=red]GTL REF Voltage Control............. - Disable[/COLOR] [COLOR=red]CPU GTL1/3 REF Volt................. - 115[/COLOR] [COLOR=red]CPU GTL 0/2 REF Volt................ - 115[/COLOR] [COLOR=red]North Bridge GTL REF Volt........... - 115[/COLOR] [B]Genie BIOS Settings:[/b] [COLOR=red]Exist Setup Shutdown................ - Mode 2[/COLOR] [COLOR=red]CLOCK VC0 divider................... - Auto[/COLOR] [COLOR=red]CPU Clock Ratio Unlock.............. - Enabled[/COLOR] [COLOR=red]CPU Clock Ratio..................... - 8[/COLOR] [COLOR=red]Target CPU Clock.................... - 3800MHz[/COLOR] [COLOR=red]CPU Clock........................... - 475[/COLOR] [COLOR=red]Boot Up Clock....................... - 265[/COLOR] [COLOR=red]DRAM Speed.......................... - 266/667[/COLOR] [COLOR=red]Target DRAM Speed................... - 1191MHz[/COLOR] [COLOR=red]PCIE Clock.......................... - 100mhz[/COLOR] [COLOR=red]PCIE Slot Config.................... - 1X 1X[/COLOR] [COLOR=red]CPU Spread Spectrum................. - Disabled[/COLOR] [COLOR=red]PCIE Spread Spectrum................ - Disabled[/COLOR] [COLOR=red]SATA Spread Spectrum................ - Disabled[/COLOR] PRIME95 + 3DMARK2001SE + 3x CPU-Z:(SCORE 64156) http://i106.photobucket.com/albums/m267/Cr...OS/3DMARK01.jpg 3DMARK2003:(SCORE 38319) http://i106.photobucket.com/albums/m267/Cr...OS/3DMARK03.jpg 3DMARK2005:(SCORE 20090) http://i106.photobucket.com/albums/m267/Cr...OS/3DMARK05.jpg 3DMARK2006:(SCORE 12286) http://i106.photobucket.com/albums/m267/Cr...OS/3DMARK06.jpg AQUAMARK 3:(SCORE 211,451) http://i106.photobucket.com/albums/m267/Cr...OS/Aquamark.jpg SHORT DESCRIPTION: 475 x 8 = 3.8GHZ @ 1.5250v 5-5-5-10 2T @ 2.270V DDR 1191 Share this post Link to post Share on other sites More sharing options...
Praz Posted September 9, 2007 Posted September 9, 2007 DFI Infinity P965-S (LGA 775) BIOS 04/24 Intel Core 2 Extreme X6800 Conroe 2.93GHz (4M L2 core) Crucial Ballistix 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) BL2KIT12864AA1065 XFX PVT80FSHF9 GeForce 8800GTX 768MB, 158.22 drivers 684/1050 HITACHI SATA II 8MB cache 80GB hdd SAMSUNG 18X SATA DVD Burner With LightScribe SILVERSTONE ST85ZF ATX12V / EPS12V 850W SLI Certified Power Supply D-tek FuZion CPU Water Block Swiftech MCW30 Chipset cooler Block [b]Genie BIOS Settings:[/b] [color=red] NB Strap Select:........................266 Exit Setup Shutdown:....................Mode2 CPU Clock Ratio:........................10X CPU Clock:..............................360 MHz Boot Up Clock:..........................Auto MHz DRAM Speed:.............................800 MHz PCI Clock:..............................100 MHz Auto Detect PCI Clk:....................Enable Spread Spectrum:........................Disable [/color] [b]CPU Feature:[/b] [color=red] Thermal Management Control:.............Disable Limit CPUID MaxVal:.....................Disable PPM Function:...........................Disable C1E Function:...........................Disable Execute Disable Bit:....................Disable Virtualization Technology:..............Disable Frequency unlimit:......................Enable [/color] [b]Voltage Settings:[/b] [color=red] CPU Voltage Setting:....................+175.0mv DRAM Voltage Setting:...................2.000V VTT Voltage Setting:....................1.200V NB 1.25V Setting:.......................1.35V SB 1.5V Setting:........................1.5V SB 1.05 Voltage Setting:................1.05V [/color] [b]DRAM Timing:[/b] [color=red] DDR Configuration Mode:.................Auto GTL+ Driving Strength:..................Auto Enhance Data Transmitting:..............Normal Enhance Addressing:.....................Normal DQ Calibration:.........................Auto Channel 1 CLK fine delay:...............Auto Channel 2 CLK fine delay:...............Auto CAS Latency Time (tCL):.................5 DRAM RAS# to CAS# Delay (tRCD):.........5 DRAM RAS# Precharge (tRP):..............5 Precharge dealy (tRAS):.................15 All precharge to Act:...................Auto REF to ACT Delay (tRFC):................30 MCH ODT Latency:........................Auto Write to PRE Delay (tWR):...............Auto Rank Write to Read (tWTR):..............Auto ACT to ACT Delay (tRRD):................Auto Read to Write delay (tRDWR):............8 Ranks Write to Write (tWRWR):...........6 Ranks Read to Read (tRDRD):.............6 Ranks Write to Read (tWRRD):............5 Read CAS# Precharge (tRTP):.............Auto All PRE to Refresh:.....................Auto [/color] Orthos (SP2004) + 3dMark2001SE + 2x CPU-Z: 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: ========== short description: 361x10 @ 3610mhz 1.485vcore / 2.00vdimm 5.0-5-5-15 1084MHz Share this post Link to post Share on other sites More sharing options...
CPDMF Posted October 4, 2007 Posted October 4, 2007 Asus P5K Premium WiFi, 0204 Bios Intel Core2 Q6600 SLACR (MP-05 Pro block) 4X1024 Transcend AxeRam DDR2-800 EVGA 8800GTS 320MB (MCW60 block) PC Power and Cooling 750w Silencer 2 X 74G WD Raptors RAID0, 250G WD SataII D5 Pump - BIX3 Radiator ========== [b]Jumper Free Configuration:[/b] Ai Overclocking............................ - [Manual] CPU Ratio Control.......................... - [Manual] Ratio CMOS Setting......................... - [8] FSB Strap To North Bridge.................. - [333MHz] FSB Frequency.............................. - [450] PCIE Frequency............................. - [105] DRAM Frequency............................. - [DDR2-900MHZ] DRAM Command Rate.......................... - [2T] DRAM Timing Control........................ - [Manual] cas# Latency............................... - [4 DRAM Clocks] RAS# To cas# Delay......................... - [4 DRAM Clocks] RAS# Precharge............................. - [4 DRAM Clocks] RAS# Active To Precharge................... - [12 DRAM Clocks] TWR........................................ - [4 DRAM Clocks] TRFC....................................... - [42 DRAM Clocks] TWTR....................................... - [4 DRAM Clocks] TRRD....................................... - [7 DRAM Clocks] TRTP....................................... - [4 DRAM Clocks] DRAM Static Read Control................... - [Enable] Transaction Booster........................ - [Auto] Clock Over Charging Mode................... - [.80] CPU Spread Specrum......................... - [Disabled] PCIE Spread Spectrum....................... - [Disabled] CPU Voltage................................ - [1.4625v] CPU Voltage Reference...................... - [.61x] CPU Voltage Damper......................... - [Enabled] CPU PLL Voltage............................ - [1.8] DRAM Voltage............................... - [2.10v] FSB Termination Voltage.................... - [1.55] North Bridge Voltage....................... - [1.55v] North Bridge Voltage Reference............. - [.67x] South Bridge Voltage....................... - [1.05] [b]CPU Configuration:[/b] CPU Ratio Control.......................... - [Manual] Ratio CMOS Setting......................... - [8] C1E Support................................ - [Disabled] Max CPUID Value Limit...................... - [Disabled] Vanderpool Technology...................... - [Enabled] CPU TM Function............................ - [Disabled] Execute Disable Bit........................ - [Disabled] PECI....................................... - [Disabled] 3DMark01-Prime95-2 X CPUZ-Everest 3Dmark03 +2 X CPUZ 3DMark05 + 2 x CPUZ 3DMark06 + 2 X CPUZ Short Description 450 X 8 @ 3600 1.4625v DDR2-900 @ 4 4 4 12 2.1v Share this post Link to post Share on other sites More sharing options...
mknwatt Posted October 6, 2007 Posted October 6, 2007 DFI LP UT P35 T2R, 9/13 BIOS OCZ DDR2 PC2-8800 Gold Dual Channel 2GB (2 x 1GB) OCZ2G11002GK Intel Core 2 Duo E6850 Conroe 3.0GHz 4M shared L2 Cashe (L723A047), Swifttech Storm Rev.2 BFG 8800GTX 768MB 384-bit GDDR3 PCI-E x16 @ 648/1026 ~ NVIDIA 158.22 drivers, DD NV-88GTX 2x Western Digital Caviar SE WD1600JS 160GB 7200 RPM 8MB Cache SATA 3.0Gb/s, RAID-0 SONY DVD RW DRU-700A PC Power & Cooling Silencer 750 Quad (Black) **Custom Water Chiller ~ cpu only** (It lower the liquid temp, function instead of looks :cool:) ========== [b]Genie BIOS Setting:[/b] [color="red"] Exit Setup shutdown....................... - Mode 2 CLOCK VCO divider......................... - Auto CPU Clock Ratio........................... - 9 X - Target CPU Clock........................ - 4176 MHz CPU Clock................................. - 464 MHz Boot Up Clock............................. - Auto DRAM Speed................................ - 333/800 - Target DRAM Speed....................... - DDR2 1114 PCIE Clock................................ - 100 MHz PCIE Slot Config.......................... - 1X 1X CPU Spread Spectrum....................... - Disabled PCIE Spread Spectrum...................... - Disabled SATA Spread Spectrum...................... - Disabled [/color] [b]CPU Feature:[/b] [color="red"] Thermal Management Control................ - Disabled PPM(EIST) Mode............................ - Disabled Limit CPUID MaxVal........................ - Disabled C1E Function.............................. - Disabled Execute Disable Bit....................... - Disabled Virtualization Technology................. - Disabled Core Multi-Processing..................... - Enabled [/color] [b]Voltage Setting:[/b] [color="red"] CPU VID Control........................... - 1.550V CPU VID Special Add....................... - Auto DRAM Voltage Control...................... - 2.350V SB 1.05V Voltage.......................... - 1.150V SB Core/CPU PLL Voltage................... - 1.75V NB Core Voltage........................... - 1.45V CPU VTT Voltage........................... - 1.30V Vcore Droop Control....................... - Disabled Clockgen Voltage Control.................. - 3.45V GTL+ Buffers Strenght..................... - Strong Host Slew Rate............................ - Weak GTL REF Voltage Control................... - Enabled CPU GTL 1/3 REF Volt..................... - 90 CPU GTL 0/2 REF Volt..................... - 90 North Bridge GTL REF Volt................. - 100 [/color] [b]DRAM Timing:[/b] [color="red"] Enhance Data transmitting................. - Fast Enhance Addressing........................ - Fast T2 Dispatch............................... - Auto CAS Latency Time (tCL).................... - 5 RAS# to CAS# Delay (tRCD)................. - 5 RAS# Precharge (tRP)...................... - 4 Precharge delay (tRAS).................... - 9 All Precharge to ACT...................... - 4 REF to ACT Delay (tRFC)................... - 28 Preformance LVL (Read delay).............. - 7 MCH ODT Latencey.......................... - 1 Write to PRE Delay (tWR).................. - 10 Rank Write to Read (tWTR)................. - 10 ACT to ACT Delay (tRRD)................... - 2 Read to Write Delay (tRDWR)............... - 8 Ranks Write to Write (tWRWR).............. - 6 Ranks Read to Read (tRDRD)................ - 6 Ranks Write to Read (tWRRD)............... - 5 Read CAS# Precharge (tRTP)................ - 2 All PRE to Refresh........................ - 5 [/color] [b]Clock Setting Fine Delay:[/b] [color="red"] Ch1 Clock Crossing Setting................ - More Aggressive DIMM 1 Clock fine delay................... - Current[ 2] DIMM 2 Clock fine delay................... - Current[ 6] Ch1 Command fine delay.................... - Current[10] Ch1 Control fine delay.................... - Current[ 7] Ch2 Clock Crossing Setting................ - More Aggressive DIMM 3 Clock fine delay................... - Current[ 2] DIMM 4 Clock fine delay................... - Current[ 7] Ch2 Command fine delay.................... - Current[10] Ch2 Control fine delay.................... - Current[ 6] Ch1Ch2 CommonClock Setting................ - More Aggressive Ch1 RDCAS GNT-Chip Delay.................. - Auto Ch1 WRCAS GNT-Chip Delay.................. - Auto Ch1 Command to CS Delay................... - Auto Ch2 RDCAS GNT-Chip Delay.................. - Auto Ch2 WRCAS GNT-Chip Delay.................. - Auto Ch2 Command to CS Delay................... - Auto [/color] [b]Read delay phase adjust:[/b] [color="red"] Channel 1 Phase 0 Pull-In................. - Auto Channel 1 Phase 1 Pull-In................. - Auto Channel 1 Phase 2 Pull-In................. - Auto Channel 1 Phase 3 Pull-In................. - Auto Channel 1 Phase 4 Pull-In................. - Auto Channel 2 Phase 0 Pull-In................. - Auto Channel 2 Phase 1 Pull-In................. - Auto Channel 2 Phase 2 Pull-In................. - Auto Channel 2 Phase 3 Pull-In................. - Auto Channel 2 Phase 4 Pull-In................. - Auto[/color] ========== Orthos - 2x CPUz - 3DMark2001SE: 72336 3DMark03: 46694 - Everest Cashe & Memory Benchmark 3DMark05: 22489 - SuperPI 1M 3DMark06: 13341 - SuperPI 32M ========== short description: 464 x9 @ 4176 MHz ~ 1.55Vcore DDR2 1114 MHz (5-5-4-9-2T) ~ 2.35Vdimm Share this post Link to post Share on other sites More sharing options...
ReelFiles Posted October 8, 2007 Posted October 8, 2007 GIGABYTE GA-P35-DS3L, F3 BIOS 2x1GB OCZ Platinum Revision 2 DDR2 800 Intel Dual-Core E2160 Allendale 1.8GHz 1MB L2 Cache PNY GeForce 7300GT 256MB 128-bit GDDR2 162.18 drivers / Stock 350/333 / OCed 477/413 Western Digital Caviar SE WS2000JS 200GB 7200 RPM 8MB Cache SATA 3.0Gb/s NEC 16x DVD_RW ND-3550A SILVERSTONE SST-ST60F ATX 600W Power Supply Dual 120mm Water Cooling Sytem ========== [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=green] Robust Graphics Booster............. - Auto CPU Clock Ratio..................... - 8x CPU Host Clock Control.............. - Enabled CPU Host Frequency (Mhz)............ - 420 PCI Express Frequency (Mhz)......... - Auto Performance Enhancer................ - Standard C.I.A.2............................. - Disabled System Memory Multiplier (SPD)...... - 2.0 Memory Frequency (Mhz).............. - 840 High Speed DRAM DLL Settings........ - Option 1 DRAM Timing Selectable (SPD)........ - Manual CAS Latency Time.................... - 5 DRAM RAS# to CAS# Delay............. - 6 DRAM RAS# Precharge................. - 6 Precharge Delay (tRAS).............. - 16 ACT to ACT Delay (tRRD)............. - 4 Bank Write to READ Delay............ - 3 Write to Precharch Delay............ - 6 Refresh to ACT Delay................ - 42 Read to Precharge Delay............. - 3 tRD................................. - 8 tRD Phase Adjustment................ - 25 System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - [+0.2] PCI-E OverVoltage Control........... - Normal FSB OverVoltage Control............. - Normal (G)MCH OverVoltage Control.......... - Normal CPU Voltage Control................. - 1.48750V Normal CPU Vcore.................... - 1.32500V [/color] ========== Prime95), 2x CPU-Z, 3dMark2001SE: 3dMark2003: 3dMark2005: 3dMark2006: Short description: 420x8 @ 3.36GHz 5-6-6-16 Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted October 11, 2007 Posted October 11, 2007 Gigabyte GA-P35-DS3R, Buffalo Firestix PC2-6400 (DDR2-800) Intel Core 2 Quad Q6600 quad-core cpu XFX 7800GT 256MB PCI-E 16x 84.21 drivers Seagate Barracuda 7200.10 ST3320620AS (Perpendicular Recording Technology) 320GB 7200 RPM 16MB Cache SATA 3.0Gb/s Lite-On 16x SATA DVD-RW OCZ GameXStream OCZ700GXSSLI ATX12V 700W Power Supply * * * * ========== [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=green] Robust Graphics Booster............. - Auto CPU Clock Ratio..................... - 9x CPU Host Clock Control.............. - Enabled CPU Host Frequency (Mhz)............ - 334 PCI Express Frequency (Mhz)......... - Auto C.I.A.2............................. - Disabled System Memory Multiplier (SPD)...... - Auto Memory Frequency (Mhz).............. - 667 (835) Performance Enhance................. - Turbo DRAM Timing Selectable (SPD)........ - Auto CAS Latency Time.................... - Auto DRAM RAS# to CAS# Delay............. - Auto DRAM RAS# Precharge................. - Auto Precharge Delay (tRAS).............. - Auto ACT to ACT Delay (tRRD)............. - Auto Bank Write to READ Delay............ - Auto Write to Precharch Delay............ - Auto Refresh to ACT Delay................ - 0 (Auto) Read to Precharge Delay............. - Auto Memory Performance Enhance.......... - Normal System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - +0.1v PCI-E OverVoltage Control........... - Normal FSB OverVoltage Control............. - +0.1v (G)MCH OverVoltage Control.......... - +0.1v CPU Voltage Control................. - Normal Normal CPU Vcore.................... - 1.30000v [/color] ========== Orthos (dual-prime95), 2x CPU-Z, 3dMark2001SE: http://www.angrygames.com/ocdb/angry/q6600..._p35_ocdb-1.gif 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: Short description: 334x9 @ 3.0Ghz 5-5-5-15 Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted November 5, 2007 Posted November 5, 2007 Gigabyte GA-965P-DS3/S3 (F10 BIOS) E6600 (L714A245) 2X1024 CRUCIAL BALLISTIX PC8500 X1900 XT-X@689/797, CAT 7.10 DRIVERS 2X36GB Western Digital Raptor SATA hdd RAID 0 LITEON 832S DVD R/W HIPER 580 MODULAR PSU Mach2 GT/Chilly1 head/Desuperheater ========== [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=green] Robust Graphics Booster............. - Auto CPU Clock Ratio..................... - 9x CPU Host Clock Control.............. - Disabled CPU Host Frequency (Mhz)............ - 456 PCI Express Frequency (Mhz)......... - 105MHz C.I.A.2............................. - Disabled System Memory Multiplier (SPD)...... - 2 Memory Frequency (Mhz).............. - 912 High Speed DRAM DLL Settings........ - Option 1 DRAM Timing Selectable (SPD)........ - Manual CAS Latency Time.................... - 4 DRAM RAS# to CAS# Delay............. - 4 DRAM RAS# Precharge................. - 4 Precharge Delay (tRAS).............. - 12 ACT to ACT Delay (tRRD)............. - Auto Bank Write to READ Delay............ - Auto Write to Precharch Delay............ - Auto Refresh to ACT Delay................ - 0 (Auto) Read to Precharge Delay............. - Auto Memory Performance Enhance.......... - fast System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - +0.4 PCI-E OverVoltage Control........... - +0.1 FSB OverVoltage Control............. - +0.1 (G)MCH OverVoltage Control.......... - +0.2 CPU Voltage Control................. - 1.6v Normal CPU Vcore.................... - 1.35v [/color] ========== Orthos, 2x CPU-Z, 3dMark2001SE: 3dMark2003: 3dMark2005: 3dMark2006: Short description: 456x9 @ 4.104Ghz 4-4-4-12 Share this post Link to post Share on other sites More sharing options...
loggan26 Posted November 19, 2007 Posted November 19, 2007 DFI Infinity 975X/G Bios: 08-20-2007 2GB OCZ DDR2 PC2-9200 1150 MHz FlexXLC Edition 240 Pin DIMM (OCZ2FX11502GK) CL 5-5-5-15 Intel Core 2 Duo E6700 Socket775 2.67GHz 4MB Cache 1066MHz FSB Conroe Core - Dtek FuZion Cpu Waterblock EVGA 8800GTX 768MB 384-bit GDDR3 PCI-E x16 @ 630/1060 Forceware 165. drivers Seagate Barracuda 7200.10 ST3320620AS (Perpendicular Recording Technology) 2x320GB 7200 RPM 16MB Cache SATA 3.0Gb/s Hard Drives in Raid0 HSPC Top Deck Tech Station (14x9.5) - Black OCZ 1000W ProXstream Genie BIOS PPM Function........................ - Enabled ---------------------------------------- CPU Clock Ratio Setting............. - 10x CPU Clock Setting................... - 371Mhz PCIE Clock Sync. With............... - O.C. Mode Current Dram Speed.................. - DDR2 928 System Memory Frequency............. - 667 PCIE Clock Setting.................. - 100MHz SATA Clock Sync. With............... - FIX 100Mhz ------------------------------------------- CPU VID Offset Setting.............. - +200v Default CPU Voltage................. - 1.3200v CPU VTT Voltage Setting............. - 1.275v DRAM Voltage Setting................ - 2.30v NB Chip Voltage Setting............. - 1.70v ------------------------------------------- Auto Detect PCI Clock............... - Enabled Spread Spectrum..................... - Disabled Memory Hole Remapping............... - Enabled DRAM Timing and Config CAS Latency Time.................... - 5 DRAM RAS# to CAS# Delay............. - 5 DRAM RAS# Precharge................. - 5 Precharge Delay (tRAS).............. - 15 Refresh Mode Select................. - Auto Write to Precharge Delay............ - Auto Write to Read Delay (Same).......... - Auto Write to Read Delay (Diff).......... - Auto Read to Write Delay................. - Auto Write Recovery...................... - Auto Read Recovery....................... - Auto Read Delay.......................... - Auto Data A Drive Strength............... - Auto Data B Drive Strength............... - Auto x8 Control Drive Strength........... - Auto x16 Control Drive Strength.......... - Auto x8 Clock Drive Strength............. - Auto x16 Clock Drive Strength............ - Auto Command A Drive Strength............ - Auto Command B Drive Strength............ - Auto Dram Data Integrity Mode............ - Non-ECC short description: 371x10 @ 3712mhz 1.58vcore / 2.30vdimm 5.0-5-5-15 928MHz Share this post Link to post Share on other sites More sharing options...
Chump Posted December 9, 2007 Posted December 9, 2007 DFI LANPARTY UT P35-T2R (BIOS 1019) INTEL CORE 2 DUO E6850 CONROE 3.0GHZ 4M L2 CACHE OCZ PC2-9600 FLEX XLC 2 x 1GB PN:OCZ2FX12002GK INNO3D 8800GTS 320MB (169.17 DRIVERS STOCK SPEED 513 X 792) 4 X HITACHI DJ 80GB HD'S (RAID 0 / 32K STRIPE) SONY DUAL LAYER DVD RW (DRU-820A) OCZ GAMEXTREAM 1010W PSU WINDOWS XP PRO SP2 CPU COOLING: D-TEK FUSION + PA130.3 + D5 VARIO [B]>CPU Feature:[/B] [COLOR=red]Thermal Management Control.......... - Disabled[/COLOR] [COLOR=red]PPM(EIST) Mode...................... - Disabled[/COLOR] [COLOR=red]Limit CPUID MaxVal.................. - Disabled[/COLOR] [COLOR=red]CIE Function........................ - Disabled[/COLOR] [COLOR=red]Execute Disable Bit................. - Enabled[/COLOR] [COLOR=red]Virtualization Technology........... - Enabled[/COLOR] [COLOR=red]Core Multi-Processing............... - Enabled[/COLOR] [B]>DRAM Timing:[/B] [COLOR=red]Enhance Data transmitting........... - Fast[/COLOR] [COLOR=red]Enhance Addressing.................. - Fast[/COLOR] [COLOR=red]T2 Dispatch......................... - Auto[/COLOR] [B]>Clock Setting Fine Delay Press Enter:[/B] [COLOR=blue]Ch1 Clock Crossing Setting......... - More Aggressive[/COLOR] [COLOR=blue]DIMM1 Clock Fine Delay............. - Current[0][/COLOR] [COLOR=blue]DIMM2 Clock Fine Delay............. - Current[5][/COLOR] [COLOR=blue]Ch1 ControlFine Delay.............. - Current[8][/COLOR] [COLOR=blue]Ch1 ControlFine Delay.............. - Current[6][/COLOR] [COLOR=blue]Ch2 Clock Crossing Setting......... - More Aggressive[/COLOR] [COLOR=blue]DIMM3 Clock Fine Delay............. - Current[0][/COLOR] [COLOR=blue]DIMM4 Clock Fine Delay............. - Current[6][/COLOR] [COLOR=blue]Ch2 ControlFine Delay.............. - Current[8][/COLOR] [COLOR=blue]Ch2 ControlFine Delay.............. - Current[5][/COLOR] [COLOR=blue]Ch1 Ch2 Common Clock Setting....... - More Aggressive[/COLOR] [COLOR=blue]Ch1 RDCAS GNT-Chip Delay........... - Auto[/COLOR] [COLOR=blue]Ch1 WRCAS GNT-Chip Delay........... - Auto[/COLOR] [COLOR=blue]Ch1 Command To CS Delay............ - Auto[/COLOR] [COLOR=blue]Ch2 RDCAS GNT-Chip Delay........... - Auto[/COLOR] [COLOR=blue]Ch2 WRCAS GNT-Chip Delay........... - Auto[/COLOR] [COLOR=blue]Ch2 Command To CS Delay............ - Auto[/COLOR] [COLOR=red]CAS Latency Time (tCL).............. - 5[/COLOR] [COLOR=red]RAS# to CAS# Delay (tRCD)........... - 5[/COLOR] [COLOR=red]RAS# Precharge (tRP)................ - 4[/COLOR] [COLOR=red]Precharge Delay (tRAS).............. - 10[/COLOR] [COLOR=red]All Precharge to Act................ - 4[/COLOR] [COLOR=red]REF to ACT Delay (tRFC)............. - 30[/COLOR] [COLOR=red]Performance Level................... - 7[/COLOR] [B]>Read delay phase adjust Press Enter:[/B] [COLOR=blue]Channel 1 Phase 0 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 1 Phase 1 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 1 Phase 2 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 1 Phase 3 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 1 Phase 4 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 0 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 1 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 2 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 3 Pull-In.......... - Auto[/COLOR] [COLOR=blue]Channel 2 Phase 4 Pull-In.......... - Auto[/COLOR] [COLOR=red]MCH ODT Latency..................... - Auto[/COLOR] [COLOR=red]Write to PRE Delay (tWR)............ - 11[/COLOR] [COLOR=red]Rank Write to Read (tWTR)........... - 10[/COLOR] [COLOR=red]ACT to ACT Delay (tRRD)............. - 3[/COLOR] [COLOR=red]Read to Write Delay (tRDWR)......... - 8[/COLOR] [COLOR=red]Ranks Write to Write (tWRWR)........ - Auto[/COLOR] [COLOR=red]Ranks Read to Read (tRDRD).......... - Auto[/COLOR] [COLOR=red]Ranks Write to Read (tWRRD)......... - Auto[/COLOR] [COLOR=red]Read CAS# Precharge (tRTP).......... - 3[/COLOR] [COLOR=red]ALL PRE to Refresh.................. - 4[/COLOR] [B]>Voltage Settings:[/B] [COLOR=red]CPU VID Control..................... - 1.47500v[/COLOR] [COLOR=red]CPU VID Special Add................. - Auto[/COLOR] [COLOR=red]DRAM Voltage Control................ - 2.27v[/COLOR] [COLOR=red]SB 1.05V Voltage.................... - 1.150v[/COLOR] [COLOR=red]SB Core/CPU PLL Voltage............. - 1.75v[/COLOR] [COLOR=red]NB Core Voltage..................... - 1.45v[/COLOR] [COLOR=red]CPU VTT Voltage..................... - 1.35v[/COLOR] [COLOR=red]Vcore Droop Control................. - Disabled[/COLOR] [COLOR=red]Clockgen Voltage Control............ - 3.60v[/COLOR] [COLOR=red]GTL+ Buffers Strength............... - Strong[/COLOR] [COLOR=red]Host Slew Rate...................... - Weak[/COLOR] [COLOR=red]GTL REF Voltage Control............. - Disable[/COLOR] [COLOR=red]CPU GTL1/3 REF Volt................. - 93[/COLOR] [COLOR=red]CPU GTL 0/2 REF Volt................ - 93[/COLOR] [COLOR=red]North Bridge GTL REF Volt........... - 93[/COLOR] [B]Genie BIOS Settings:[/B] [COLOR=red]Exist Setup Shutdown................ - Mode 2[/COLOR] [COLOR=red]CLOCK VC0 divider................... - Auto[/COLOR] [COLOR=red]CPU Clock Ratio Unlock.............. - Enabled[/COLOR] [COLOR=red]CPU Clock Ratio..................... - 8[/COLOR] [COLOR=red]Target CPU Clock.................... - 4000MHz[/COLOR] [COLOR=red]CPU Clock........................... - 500[/COLOR] [COLOR=red]Boot Up Clock....................... - 350[/COLOR] [COLOR=red]DRAM Speed.......................... - 333/800[/COLOR] [COLOR=red]Target DRAM Speed................... - 1201MHz[/COLOR] [COLOR=red]PCIE Clock.......................... - 100mhz[/COLOR] [COLOR=red]PCIE Slot Config.................... - 1X 1X[/COLOR] [COLOR=red]CPU Spread Spectrum................. - Disabled[/COLOR] [COLOR=red]PCIE Spread Spectrum................ - Disabled[/COLOR] [COLOR=red]SATA Spread Spectrum................ - Disabled[/COLOR] PRIME95 + 3DMARK2001SE + 3x CPU-Z:(SCORE 60647) http://i106.photobucket.com/albums/m267/Cr...00/3DMARK01.jpg 3DMARK2003:(SCORE 33679) http://i106.photobucket.com/albums/m267/Cr...00/3DMARK03.jpg 3DMARK2005:(SCORE 18195) http://i106.photobucket.com/albums/m267/Cr...00/3DMARK05.jpg 3DMARK2006:(SCORE 10289) http://i106.photobucket.com/albums/m267/Cr...00/3DMARK06.jpg AQUAMARK 3:(SCORE 206,733) http://i106.photobucket.com/albums/m267/Cr...00/Aquamark.jpg SHORT DESCRIPTION: 500 x 8 = 4.0GHZ @ 1.4750v 5-5-4-10 2T @ 2.270V DDR 1201 Share this post Link to post Share on other sites More sharing options...
slick2500 Posted December 14, 2007 Posted December 14, 2007 GIGABYTE GA-P35-DS3L, F6 BIOS 2x1GB OCZ Reaper HPC Edition DDR2 800 Intel Dual-Core E2140 Allendale 1.6GHz 1MB L2 Cache eVga Geforce 7800GT 169.09 drivers / 445/1070 Western Digital Caviar SE16 WD2500AAKS 250GB 7200 RPM 16MB Cache SATA 3.0Gb/s Lite-On 20X DVD+R LH-20A1S OEM BK OCZ GameXStreme CZ700GXSSLI ATX12V 700W Power Supply ========== [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=green] Robust Graphics Booster............. - Auto CPU Clock Ratio..................... - 8x CPU Host Clock Control.............. - Enabled CPU Host Frequency (Mhz)............ - 375 PCI Express Frequency (Mhz)......... - Auto Performance Enhancer................ - Standard C.I.A.2............................. - Disabled System Memory Multiplier (SPD)...... - 2.4 Memory Frequency (Mhz).............. - 900 DRAM Timing Selectable (SPD)........ - Auto CAS Latency Time.................... - 5 DRAM RAS# to CAS# Delay............. - 5 DRAM RAS# Precharge................. - 5 Precharge Delay (tRAS).............. - 15 ACT to ACT Delay (tRRD)............. - 4 Bank Write to READ Delay............ - 3 Write to Precharch Delay............ - 6 Refresh to ACT Delay................ - 42 Read to Precharge Delay............. - 3 tRD................................. - 8 tRD Phase Adjustment................ - 25 System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - [+0.2] PCI-E OverVoltage Control........... - Normal FSB OverVoltage Control............. - Normal (G)MCH OverVoltage Control.......... - Normal CPU Voltage Control................. - 1.37600V Normal CPU Vcore.................... - 1.32500V [/color] ========== Orthos, 2x CPU-Z, 3dMark2001SE: 3dMark2003: 3dMark2005: 3dMark2006: AquaMark3: Short description: 375x8 @ 3GHz 5-5-5-15 Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now