Jump to content

Recommended Posts

Your max async has gotta be 8.0ns, the other time i tested UTTs, at 1:1 250Mhz MAL could be 7ns, but once i set it one 300HTT with a 166Mhz divider to run 250Mhz, MAL has to be at 8ns for stability.

Share this post


Link to post
Share on other sites

It's runnin' fine how it is :- lol

 

Just rebooted and set to this:

 

Genie BIOS Settings:

 

FSB Bus Frequency............................. - 334

LDT/FSB Frequency Ratio....................... - 3x

CPU/FSB Frequency Ratio....................... - 9x

PCI eXpress Frequency......................... - 101Mhz

 

CPU VID StartUp Value......................... - Auto

 

CPU VID Control............................... - 1.525V

CPU VID Special Control....................... - + 104.8%

LDT Voltage Control........................... - 1.30v

Chip Set Voltage Control...................... - 1.59v

DRAM Voltage Control.......................... - 2.87V

 

DRAM Configuration Settings:

 

DRAM Frequency Set............................ - 100=RAM/FSB:01/02

Command Per Clock (CPC)....................... - Enable

CAS Latency Control (Tcl)..................... - 2.5

RAS# to CAS# delay (Trcd)..................... - 3

Min RAS# active time (Tras)................... - 5

Row precharge time (Trp)...................... - 2

Row Cycle time (Trc).......................... - 10 Bus Clocks

Row refresh cyc time (Trfc)................... - Auto

Row to Row delay (Trrd)....................... - 02 Bus Clocks

Write recovery time (Twr)..................... - 02 Bus Clocks

Write to Read delay (Twtr).................... - 02 Bus Clocks

Read to Write delay (Trwt).................... - 03 Bus Clocks

Refresh Period (Tref)......................... - 4708 Cycles

DRAM Bank Interleave.......................... - Enabled

 

DQS Skew Control.............................. - Increase Skew

DQS Skew Value................................ - 50

DRAM Drive Strength........................... - auto

DRAM Data Drive Strength...................... - auto

Max Async Latency............................. - 7ns

DRAM Response Time............................ - fast

Read Preamble Time............................ - 5ns

IdleCycle Limit............................... - 16 Cycles

Dynamic Counter............................... - Disable

R/W Queue Bypass.............................. - 16 x

Bypass Max.................................... - 04 x

32 Byte Granularity........................... - Disable(4 Bursts)

 

Booted right up and actually improved my boot time from 3 bars, to 2.5 bars LMAO

Share this post


Link to post
Share on other sites

Okay same settings but the ram is now running with a CAS of 2

 

gonna run AM3 then I'll set it to Prime and hope for the best... gotta say the RAM only running at 167x2 sucks but y'know what... for now, it'll work untiL I can get the OCZ replaced.

Share this post


Link to post
Share on other sites
Okay same settings but the ram is now running with a CAS of 2

 

gonna run AM3 then I'll set it to Prime and hope for the best... gotta say the RAM only running at 167x2 sucks but y'know what... for now, it'll work untiL I can get the OCZ replaced.

Sounds like you got yourself a good chip there, hopefully i'll see a new post in the ocdb in the morning.

Share this post


Link to post
Share on other sites

I have a OCDB entry ready for 2950 But I cant get 06 to work. can ya help me with 3Dmark 06? I have downloaded it 5 times and some down loads take 8 hours. every time I install it i get the same error

06errorvc3.png

Share this post


Link to post
Share on other sites
I have a OCDB entry ready for 2950 But I cant get 06 to work. can ya help me with 3Dmark 06? I have downloaded it 5 times and some down loads take 8 hours. every time I install it i get the same error

06errorvc3.png

 

I wish I could help you but I'm as clueless as you are.

Share this post


Link to post
Share on other sites
I wish I could help you but I'm as clueless as you are.

I googled it and said that (Management Instrument (WMI) services needed to be started in services but I cant even find the service ?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...