Jump to content
Sign in to follow this  
Angry_Games

Evercool VC-RE Chipset Fan Installation Tutorial Video! (2 fast mirror

Recommended Posts

I got this and found there was some of the yellow sticky crap from the dfi cooler litterally like melded onto my chipset chip..can I safely use a knife to scrape this crap off? I applied as5, but it's not really helping my temps and i credit it to this goop

Share this post


Link to post
Share on other sites
I got this and found there was some of the yellow sticky crap from the dfi cooler litterally like melded onto my chipset chip..can I safely use a knife to scrape this crap off? I applied as5, but it's not really helping my temps and i credit it to this goop

NEVER use a knife on ANY electrical component!!!!!

 

 

 

get some 100% acetone

 

you can get it in the beauty section of any drug store....make sure you get 100% pure acetone that has no fillers, colors, additives, etc

 

 

soak a paper towel or coffee filter or rag etc in a spot and apply it to the chip with a little pressure....after 30-90 seconds you should have penetrated the stuff enough to easily just wipe it off with the rag or towel

 

 

 

at worst, a plastic credit card/driver's license should be used to scrape...but NEVER anything sharp or that has an edge or is harder than the chip!!!!

 

read this for more:

 

http://www.angrygames.com/chipset_clean-1.htm

Share this post


Link to post
Share on other sites

I've installed the VC-RE and my temps didn't change that much, still IDLing around 30-35c, and not sure about load, i'm sure it's on there pretty damn good though. I probably needed to watch Angry's pron video, but it's so slow. I could go to vegas and back by the time it's done man, what's the deal here? 33.6k? :)

Share this post


Link to post
Share on other sites

So the seccond mirror has used about 9 gigs worth of bandwith. I have no idea when I uploaded it so we'll just say it's been a week ;).

Share this post


Link to post
Share on other sites

If I dont have 100% acetone, but have some nail polish remover from my mom..will that work as long as im careful where I wipe it?

Share this post


Link to post
Share on other sites

Nail polish remover will be composed of mostly acetone but you have to be careful with it because they often put other things such as fragrances and color that will not come evaporate along with the acetone.

Share this post


Link to post
Share on other sites

What I wil ldo is use the nail polish and then wipe it clean with some 90% isoporyl I alos just did the dab method with the as5 instead of evenly spreading it, which is another reason why I probably didnt get the results I wanted. My ultra-d to sli mod pins are covered in a greenish blackish thing...How can I easily remove this to perform the sli mod?

Share this post


Link to post
Share on other sites
If I dont have 100% acetone, but have some nail polish remover from my mom..will that work as long as im careful where I wipe it?

do not use it

 

only use 100% acetone that is free from other ingredients

 

period

Share this post


Link to post
Share on other sites
My ultra-d to sli mod pins are covered in a greenish blackish thing...How can I easily remove this to perform the sli mod?

there's a giant tutorial thread here full of this information...use the search function within the thread to find what you are looking for (it is epoxy covering those two points you have to connect to make the mod work)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×