Jump to content
Sign in to follow this  
richiec77

Opty 165 Overclocking database

Recommended Posts

Just bought mine from ebay today and hopefully I'll get it in on tuesday(stepping in sig). Of course I can't OC it to the max since i only have a 400w codegen. I don't really think I would want to risk running my system on it since I had a 4 LED problem and had to get it RMA'd. Ima see if I can get my psu asap and post the results.

Share this post


Link to post
Share on other sites
11dayz i just received that same stepping :O

I'll be interested to hear the results. Good luck :)

 

WHat are your temps like?

25 Idle, 40 Load typically. It varies by a couple degrees as I micromanage my A/C to offset electric bill rate hikes :mad: Load temps got up to 44 when I tried 1.65v just to see if I could get higher. At that voltage I could get into windows at 2.6 but superPi would error out.

Share this post


Link to post
Share on other sites
2.61ghz, 1.45v. 0551

There are plenty of 165 results in the AMD Overclcoking Database as well

All readings from software read about 0.03v below the actual voltage.

Hey burky...I have the exact same revision as you...how are your temps?

Share this post


Link to post
Share on other sites
Guest shaolin95

2780MHZ @ 1.52v

All the info in my sig.

Share this post


Link to post
Share on other sites
2520 (280x9 @ 1.5v)

Stepping CCBWE 0607UPGW

 

 

I'm pretty dissappointed with mine. Haven't seen many people with the same stepping either, so I can't compare.

 

Hey, 11dayz,

 

I have the same stepping as you and I've only been able to get to to 2403 (267x9 @ 1.45v). It's prime stable now and I'm going to let it burn in a bit here and then I'll try pushing it up some more. Here's my settings; any input/comments are welcome.

 

FSB Bus Frequency ............................ 267 MHz

LDT/FSB Frequency Ratio ...................... 3

CPU/FSB Frequency Ratio ...................... Auto

PCI eXpress Frequency ........................ 100

CPU VID StartUp Value ........................ StartUp

 

CPU VID Control .............................. 1.450v

CPU VID Special Control ...................... Auto

LDT Voltage Control .......................... 1.30v

Chip Set Voltage Control ..................... 1.60V

DRAM Voltage ................................. 2.60v

+0.03 if not 3.2V ............................ Enable

 

Memclock (DRAM Frequency) .................... 180 (9/10)

1T/2T Timing (Command Per Clock).............. 1T

CAS Latency (Tcl)............................. 3T

RAS# to CAS# delay (Trcd)..................... 4T

Min RAS# active time (Tras)................... 8T

Row precharge time (Trp)...................... 3T

Row Cycle time (Trc).......................... 11T

Row refresh cyc time (Trfc)................... 16T

Row to Row delay (Trrd)....................... 3T

Write recovery time (Twr)..................... 3T

Write to Read delay (Twtr).................... 2T

Read to Write delay (Trwt).................... 3T

Refresh Period (Tref)......................... 3120

Write CAS Latency (Twcl) ..................... Auto

DRAM Bank Interleave.......................... Enabled

 

DQS Skew Control.............................. Auto

DQS Skew Value................................ 0

DRAM Drive Strength........................... Level 7

DRAM Data Drive Strength...................... Level 2

Max Async Latency............................. 8ns

DRAM Response Time............................ Normal

Read Preamble Time............................ 6ns

IdleCycle Limit............................... 256 Cycles

Dynamic Counter............................... Disable

R/W Queue Bypass.............................. 16x

Bypass Max.................................... 7x

32 Byte Granularity........................... Disable (4 Bursts)

Share this post


Link to post
Share on other sites

Wow. Nice job on the 0610 sumofatguy :). I hope to get mine to at least 2.6 when I get a better power supply. For now ima probably have to remove a lot of the extra stuff in my system so my board has more power. Hopefully itll arrive here tomorrow since the guy shipped it today in the morning via Priority Mail.

Share this post


Link to post
Share on other sites

CCBWE 0601 UPMW i seem to have a bad stepping as most people cant get over 2.6 with 24hr stability

2.5Ghz @ 1.450v - 24hr prime stable

2.61Ghz @ 1.55v this was pretty much the limit as i lost stability after this - 8 hr prime stable

 

FSB: 278

LDT/FSB: 3x

CPU/FSB: x9

CPU Vid: 1.450

CPU Vid Special Control: Auto

DRAM Voltage: 2.80

 

Memory (Not optimised yet:

DRAM Frequency: 166Mhz (5/06)

CPC: Enable

Tcl: 3

Trcd: 3

Tras: 8

Trp: 3

Trc: 7

Trfc: 15

Trrd: 2

Twr: 2

Twtr: 2

Trwt: 3

Tref: 3120

Twcl: 1

DRAM Back Inteleve: Enabled

 

DQS Skew: Auto (Disabled)

DQS Skew Value: 0

DRAM Drive Strength: Auto (Weak)

DRAM Data Drive Strength: Auto

Max Async Latency: 8

DRAM Responce Time: Normal

Read Preamble Time: 6.5ns

Idle Cycle Limit: 256

Dynamic Counter: Disable

R/Q Queue Bypass: 16x

Bypass Max: 7x

32 Byte Granlarity: Disable

Share this post


Link to post
Share on other sites

Chronic_tank your figures don't make sense - "1.5Ghz @ 1.45v and 1.6Ghz @ 1.55v" i'm guessing you mean 2.5 and 2.6? I have exactly the same stepping. 2.6 is pretty much as far as I can go really. I can get into windows @ 2.7 but prime fails after 2mins. I can get prime stable at 1.5v so for the money that's not too bad really - FX60 speeds for £250. You can't complain. WHat sort of temps you getting with the Sythe ninja?

 

Wow I think this is the most popular thread I have started lol. Keep up the good work guys! anyone else got the 0601 stepping?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...