Jump to content
Sign in to follow this  
B4L1STA

Corsair XMS RAM + DFI Boards

Recommended Posts

Corsair XMS 2048 4000PT

 

FSB to 260. No problems. However these particular pieces can only go to CAS 2.5

That's what i'm using and it'll do 280 with the divider at 1 to 1 easy

Share this post


Link to post
Share on other sites

Would people please post their settings for TWINX2048-4000PT please.

I'm curious as to why my set is limited to 260.

 

CPU 300x9.... I have to use the divider because of my RAM. If I could get 280 on the ram, that would be awesome.

 

DRAM Configuration Settings:

 

DRAM Frequency Set - 166 (5:6)

Command Per Clock (CPC) - Enable

CAS Latency Control (Tcl) - 3

RAS# to CAS# delay (Trcd) - 4 Bus Clocks

Min RAS# active time (Tras) - 8 Bus Clocks

Row precharge time (Trp) - 4 Bus Clocks

Row Cycle time (Trc) - 8 Bus Clocks

Row refresh cyc time (Trfc) - 14 Bus Clocks

Row to Row delay (Trrd) - 3 Bus Clocks

Write recovery time (Twr) - 3 Bus Clocks

Write to Read delay (Twtr) - 2 Bus Clocks

Read to Write delay (Trwt) - 3 Bus Clocks

Refresh Period (Tref) - 3120

Write CAS Latency (Twcl) - Auto

DRAM Bank Interleave - Enabled

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - 7

DRAM Data Drive Strength - 1

Max Async Latency - 8

DRAM Response Time - Normal

Read Preamble Time - 5.5

IdleCycle Limit - 256 Cycles

Dynamic Counter - disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(4 Bursts)

Share this post


Link to post
Share on other sites

I thought the Opteron 165 would do x10 multi? My 144 is on 290x9 too. My Corsair 3200c2pt wont go much above DDR 440 either on 2.8v so I'm running a divider. Or maybe I'm just to scared to increase the voltage anymore, but I did try to increase it but got knocked back and didn't want to kill it just yet till I can afford some more.

 

Wouldn't having slower bus with no divider on a x10 multi be better?

Share this post


Link to post
Share on other sites

Here's my settings

Fsb Bus Frequency 280

CPU/FSB Frequency Ratio x10.0

Dram Voltage Control 2.92V

DRAM Configuration Settings:

 

DRAM Frequency Set -(MHZ) 200=ram/fsb :01/01

Command Per Clock (CPC) - Enable

CAS Latency Control (Tcl) - 3

RAS# to CAS# delay (Trcd) - 4 Bus Clocks

Min RAS# active time (Tras) - 10 Bus Clocks

Row precharge time (Trp) - 4 Bus Clocks

Row Cycle time (Trc) - 12 Bus Clocks

Row refresh cyc time (Trfc) - 20 Bus Clocks

Row to Row delay (Trrd) - 2 Bus Clocks

Write recovery time (Twr) - 3 Bus Clocks

Write to Read delay (Twtr) - 2 Bus Clocks

Read to Write delay (Trwt) - 3 Bus Clocks

Refresh Period (Tref) - 4708

Write CAS Latency (Twcl) - 01 bus clocks

DRAM Bank Interleave - Enabled

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - 8

DRAM Data Drive Strength - 4

Max Async Latency - auto

DRAM Response Time - fast

Read Preamble Time - auto

IdleCycle Limit - 256 Cycles

Dynamic Counter - disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(4 Bursts)

__________________

Share this post


Link to post
Share on other sites
Here's my settings

Fsb Bus Frequency 280

CPU/FSB Frequency Ratio x10.0

Dram Voltage Control 2.92V

DRAM Configuration Settings:

 

DRAM Frequency Set -(MHZ) 200=ram/fsb :01/01

Command Per Clock (CPC) - Enable

CAS Latency Control (Tcl) - 3

RAS# to CAS# delay (Trcd) - 4 Bus Clocks

Min RAS# active time (Tras) - 10 Bus Clocks

Row precharge time (Trp) - 4 Bus Clocks

Row Cycle time (Trc) - 12 Bus Clocks

Row refresh cyc time (Trfc) - 20 Bus Clocks

Row to Row delay (Trrd) - 2 Bus Clocks

Write recovery time (Twr) - 3 Bus Clocks

Write to Read delay (Twtr) - 2 Bus Clocks

Read to Write delay (Trwt) - 3 Bus Clocks

Refresh Period (Tref) - 4708

Write CAS Latency (Twcl) - 01 bus clocks

DRAM Bank Interleave - Enabled

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - 8

DRAM Data Drive Strength - 4

Max Async Latency - auto

DRAM Response Time - fast

Read Preamble Time - auto

IdleCycle Limit - 256 Cycles

Dynamic Counter - disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(4 Bursts)

__________________

 

Muppet,

 

Thank You for posting. This will help me tons.

Just curious do you have any Benchies to post? :D

Share this post


Link to post
Share on other sites

Muppet,

 

DAMNNN!! VERY VERY Nice. :D

 

I'm hoping that I can do much better than what I am currently hitting. I have a X1900XTX that is actually underclocked and I have tried ATI Tool, CCC and they pretty much suck :mad: . Is your GTX overclocked? When I get home today I will try and adjust some of my DRAM settings and figure out how to get my X1900XTX to at least run at default speeds. Then I will bech again and see if I can at least get my RAM higher.

 

Thanks for your posts!!!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×