LOC131 Posted February 10, 2006 Posted February 10, 2006 im am a first time builder and i this is what i am planning on getting DFI LANPARTY nF4 SLI-DR ATX AMD Motherboard AMD Athlon 64 3700+ San Diego 1GHz FSB Socket 939 500 Watt ATX(already have) so my question is will these all mesh well together and what would the best ram be to get. and any other advice would be greatly appreciated. if u think there is a better mobo let me know. thx for help Quote Share this post Link to post Share on other sites More sharing options...
SeanDude05 Posted February 10, 2006 Posted February 10, 2006 Can you give detailed info about your Power Supply? There's more improtant info than just the wattage. OCZ, Corsair, Crucial and Kingston have been good on these boards, Im currently pushing my DDR400 Corsair to DDR470, and it still has some room to go. Quote Share this post Link to post Share on other sites More sharing options...
LOC131 Posted February 10, 2006 Posted February 10, 2006 Leads: Dimensions: Environmental: 20 Pin ATX cable Combined Power Overvoltage Protection MTBF: Efficiency: AC Input: 50,000 hours 65% minimum, 75% typical, at full load Select 90-132VAC or 180-264VAC, 47-63 Hz Safety: Short Circuit Protection Max Ripple Line Tolerance y y y p +3.3V & +5V 260W Plus+12V 472W +3.3V, +5V, +12V All outputs +3.3V & +5V 50 mVpp, +12V & -12V 50 mVpp, -5V & +5VSB 50 mVpp +3.3V +/-1%, +5V +/-1%, +/-12V +/-1%, -5V +/-1%, +5VSB +/-1% Power Supply Box Internally located AC line fuse +5V@52A, +3.3V@28A, +12V@20A, [email protected], [email protected], [email protected] Input Protection Max Load Current 1 20-Pin ATX, 1 Auxiliry, 1 ATX 12V, 8 x Peripheral, 2 Floppy, 1 Serial ATA 140L x 150W x 86H mm (5.5"x6"x3.3") Operate 0 to 50°C; Storage -40 and 70°C UL, FCC, CSA, TUV, NEMKO, DEMKO, SEMKO, FI, CE certification is this what u were looking for all of this detailed stuff is very new to me Quote Share this post Link to post Share on other sites More sharing options...
SeanDude05 Posted February 10, 2006 Posted February 10, 2006 The amperage on the +12V is low. Also it states it is a 20-pin ATX connector, you need a 24-pin connector. Quote Share this post Link to post Share on other sites More sharing options...
lowboy Posted February 10, 2006 Posted February 10, 2006 As you have no sig to know what your wanting to build. You would need a new PSU as the board needs 26A on 12v rails for single card or 32A for sli.See below sig for psus. Quote Share this post Link to post Share on other sites More sharing options...
LOC131 Posted February 10, 2006 Posted February 10, 2006 it actually has a 20 or 24 atx connecter what would be a good board to coincide with this. i will up grade if i have to i work in a retail store that i get extremely good discounts on ram and other types of things for computers Quote Share this post Link to post Share on other sites More sharing options...
lowboy Posted February 10, 2006 Posted February 10, 2006 You need a good psu pick one from the recommended Alist. Quote Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.