Jump to content
Sign in to follow this  
ooztuncer

G.Skill HZ/Any other UCCC (2x1024) 260+ please post here

Recommended Posts

Updated my post #63 with tighter timings for 270MHz. Please update the the cheat sheet if you would... Also, I'm going to try out OCZ Tony's bios and will post with results after that as well.

Share this post


Link to post
Share on other sites

trying to get memtest stable i keep getting errors on test 5 just at the end 6 errors settings are 250-4-8-100-1.3-1.62-2.71 - 200-enable-3-4-8-4-9-14-2-2-2-3-3120-1-enable-decrease-0-5-3-9-normal-6.5-256-disable-16-7-disable

Share this post


Link to post
Share on other sites
trying to get memtest stable i keep getting errors on test 5 just at the end 6 errors settings are 250-4-8-100-1.3-1.62-2.71 - 200-enable-3-4-8-4-9-14-2-2-2-3-3120-1-enable-decrease-0-5-3-9-normal-6.5-256-disable-16-7-disable

 

try: 250-4-8-100-1.4-1.62-2.84 - 200-enable-3-4-8-4-10-14-2-2-2-3-3120-1-enable-increase-255-7-1-9-normal-6.5-32-disable-16-7-disable

 

See how that does for you. If it doesn't work out, then I'd say try your drive and data drive strengths in different configurations. 8-4 will yeild the best band width, but not so good stability. Even numbers are strong and odd numbers are weak with it being weaker the lower you go. You shouldn't need it real strong to run stable at the SPD settings so I think the 7-1 should work for you. If the problem is your memory controller on your chip, then you may need to up the max async latency or the read preamble a bit.

Share this post


Link to post
Share on other sites
try: 250-4-8-100-1.4-1.62-2.84 - 200-enable-3-4-8-4-10-14-2-2-2-3-3120-1-enable-increase-255-7-1-9-normal-6.5-32-disable-16-7-disable

 

has no erros so far on pass 1 finished test 1-5 will let it test for the day and i have to work so we will see.

 

thanks first settings that when doing a full test go past test 5 with no issues.

 

and one thing did you ever like the 11/2/05 bios better?

Share this post


Link to post
Share on other sites

No problem... glad I could be of some help. :nod: Let me know if you have any more issues. If not then you might be able to tighten those timings up some. I have never used the 11/2/05 bios, so I can't tell you anything about that one, but I'm getting ready to flash OCZ Tony's beta bios this weekend which I will post results from when done.

 

 

has no erros so far on pass 1 finished test 1-5 will let it test for the day and i have to work so we will see.

 

thanks first settings that when doing a full test go past test 5 with no issues.

 

and one thing did you ever like the 11/2/05 bios better?

Share this post


Link to post
Share on other sites

Wow...props to the thread starter for such a good thread. My HZ's should be here any minute....so i'm getting ready to see what happens. Alot of people are using the g.skill HZ's now, which is awesome. Just in case anybody reading this wants to get them, they are $174usd(with MIR) on newegg as we speak.

 

I can't wait for them to get here.....i will post up my overclock and settings as soon as i get done. Thanks again for such a great thread for the HZ users!!

 

CJ

Share this post


Link to post
Share on other sites

Ok........got the HZ's in the yellow slots, it looks like they won't go over 280 at the moment. Trying some different settings at the moment. Should i try the orange slots?

 

CJ

Share this post


Link to post
Share on other sites

they should be in the orange slots, did you get stable at any speeds in the yellow?

Share this post


Link to post
Share on other sites
they should be in the orange slots, did you get stable at any speeds in the yellow?

 

277mhz

 

CJ

 

200

enabled

3

4

8

4

9

14

2

2

2

4

3120

enabled

increase

255

weak 3

level 1

9

normal

6.5

256

disable

16x

7x

dis

Share this post


Link to post
Share on other sites

==========

 

 

Genie BIOS Settings:

FSB Bus Frequency - 265

LDT/FSB Frequency Ratio - 3

CPU/FSB Frequency Ratio - 11

PCI eXpress Frequency - 100Mhz

 

CPU VID StartUp Value - startup

 

CPU VID Control - 1.5500v

CPU VID Special Control - Above VID * 104.8%

LDT Voltage Control - 1.20v

Chip Set Voltage Control - 1.52v

DRAM Voltage Control - 2.60v

 

DRAM Configuration Settings:

DRAM Frequency Set - 200=RAM/FSB:01/01

Command Per Clock (CPC) - auto

CAS Latency Control (Tcl) - auto

RAS# to CAS# delay (Trcd) - auto

Min RAS# active time (Tras) - auto

Row precharge time (Trp) - auto

Row Cycle time (Trc) - 07 Bus Clocks

Row refresh cyc time (Trfc) - 14 Bus Clocks

Row to Row delay (Trrd) - 03 Bus Clocks

Write recovery time (Twr) - 03 Bus Clocks

Write to Read delay (Twtr) - 02 Bus Clocks

Read to Write delay (Trwt) - 03 Bus Clocks

Refresh Period (Tref) - 3120 Cycles

Write CAS Latency (Twcl) - 01

DRAM Bank Interleave - Enabled

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - Level 7

DRAM Data Drive Strength - Level 3

Max Async Latency - 8.0 Nano Seconds

DRAM Response Time - normal

Read Preamble Time - 5.0 Nano Seconds

IdleCycle Limit - 256 Cycles

Dynamic Counter - Disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(4 Bursts)

 

here are my settings....passed all benches for stability. :nod:

should i post screenies here or in oc data base?

Share this post


Link to post
Share on other sites

Well..........277mhz no errors

DFI NF4 Ultra-D

277

704-2BTA

2.6v

 

 

 

200

enable

3

4

8

4

7

14

2

2

2

3

3684

enable

off

0

weak4

level3

8

normal

5

256

enable

16x

7x

disable

 

I will end up running 300*9 on the 183 divider which will bring ram to 270mhz. These HZ sticks rock!!

 

Please enter me into the spreadsheet! Thanks for all the helpful info.

 

CJ

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...