Jump to content
Sign in to follow this  
wdogg

Bios settings

Recommended Posts

Hello,

 

I have a DFI NF4 Ultra D mobo and am using OCZ DDR 400 Dual channel memory... I have a question about the memory configurations in the bios. This memory has a CAS Lat of 2 and a timing of 2325 with the volt at 2.6. Should I manually set these in the bios or just go with the auto. If I need to manually set these could you tell me what to set. I am not trying to Overclock, I just want it setup at what its supposed to be at. Below is a link to the ram just in case.

 

Type of memory

Share this post


Link to post
Share on other sites

Hello,

 

Take another look at the memory you have and the link you have linked to.

 

Platinum REV2 2-2-2-5 does not come in 2x1GB.

Share this post


Link to post
Share on other sites

http://www.ocztechnology.com/products/memo...hannel_platinum

 

I know :), just wanted to see if you spotted your mistake.

 

Anyway, the timings of 2-3-2-5 should be automatically detect by the bios.

 

If not just go to

GENIE BIOS Setting

>DRAM Configuration..................Press Enter = New Menu

FSB BUS Frequency....................200

LDT/FSB Frequency Ratio..............X 5.0

LDT BUS Transfer Width...............16 16

CPU/FSB Frequency Ratio..............AUTO

PCI eXpress Frequency................100Mhz

K8 Cool 'n' Quiet Support............Disable

Cool 'n' Quiet MAX FID...............AUTO

CPU VID StartUp Value................StartUp

 

CPU VID Control......................1.4v

CPU VID Special Control..............104%

LDT Voltage Control..................1.20 V

Chip Set Voltage Control.............1.40 V

DRAM Voltage Control.................2.6V

 

Run MemTest86+.......................Enabled, if you want to run memtest

GENIE BIOS Setting >DRAM Configuration

DRAM Frequency Set (MHZ).............200 (DRAM/FSB:1/01)

Command per clock (CPC)..............Enabled

Cas latency (tCL)....................2

RAS to CAS delay (tRCD)..............3

Min RAS active time (tRAS)...........5

Row precharge time (tRP).............2

Row cycle time (tRC).................AUTO

Row refresh cycle time(tRFC).........AUTO

Row to Row delay (tRRD)..............AUTO

Write recovery time (tWR)............AUTO

Write to read delay (tWTR)...........AUTO

Read to write delay (tRWT)...........AUTO

Refresh period (tREF)................AUTO

Write CAS latency (tWCL).............1

DRAM Bank Interleave.................Enabled

 

DQS Skew Control.....................AUTO

DQS Skew Value.......................0

DRAM Drive Strength..................Level 8

DRAM Data Drive Strength.............Level 3

Max Async Latency....................6ns

Dram Response........................AUTO/Normal

Read Preamble Time...................5ns

Idle Cycle Limit.....................AUTO

Dynamic Counter......................AUTO

R/W Queue Bypass.....................AUTO

Bypass Max...........................AUTO

32 Byte Granularity..................Disabled (4 bursts)

 

All the other settings on Auto can be tweaked but if you fear playing around with them just leave them alone.

 

Or ask AndyOCZ or RyderOCZ for some settings.

http://www.dfi-street.com/forum/member.php?u=323

http://www.dfi-street.com/forum/member.php?u=3834

Share this post


Link to post
Share on other sites

Thanks for the help... I am new to this so, do you think I should go through my bios and set up with the specs you have given? I just want it set at what it should be at. Thanks again!

Share this post


Link to post
Share on other sites

Why not just download CPU-z and run it? It'll tell you what you memory is running at so you won't have to change it if you don't need to.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...