Jump to content
Sign in to follow this  
Choralone

Anything to make this better?

Recommended Posts

Trying to optimize my ram a bit more i want to keep my CPU at around 2400mhz is there anything else i can do to optimize my settings.

 

If more info is needed let me know.

 

My first time OCing :D

 

Genie BIOS Settings:

 

FSB Bus Frequency - 240

LDT/FSB Frequency Ratio - X4

CPU/FSB Frequency Ratio - X10

PCI eXpress Frequency - 100Mhz

CPU VID StartUp Value - 1.500v

CPU VID Control - 1.300v

CPU VID Special Control - Above VID * 123%

LDT Voltage Control - 1.30v

Chip Set Voltage Control - 1.70v

DRAM Voltage Control - 3.20v

 

 

 

DRAM Configuration Settings:

 

 

DRAM Frequency Set - 200=RAM/FSB:1/01

Command Per Clock (CPC) - Enable

CAS Latency Control (Tcl) - 2.0

RAS# to CAS# delay (Trcd) - 03 Bus Clocks

Min RAS# active time (Tras) - 02 Bus Clocks

Row precharge time (Trp) - 05 Bus Clocks

Row Cycle time (Trc) - 07 Bus Clocks

Row refresh cyc time (Trfc) - 14 Bus Clocks

Row to Row delay (Trrd) - 02 Bus Clocks

Write recovery time (Twr) - 03 Bus Clocks

Write to Read delay (Twtr) - 01 Bus Clocks

Read to Write delay (Trwt) - 02 Bus Clocks

Refresh Period (Tref) - 3120 Cycles

Write CAS Latency (Twcl) - Auto

DRAM Bank Interleave - Enable

 

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - Level 8

DRAM Data Drive Strength - Level 2

Max Async Latency - Auto

DRAM Response Time - Fast

Read Preamble Time - Auto

IdleCycle Limit - 256 Cycles

Dynamic Counter - Disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(4 Bursts)

Share this post


Link to post
Share on other sites

You can most likely set Trfc to 12. minor change

 

(Twr) 03

(Twtr) 01

(Trwt) 02

Might want to change WR to 2.

 

1.300v

*123%

This equates to 1.599 volts on the CPU. Do you really need this much for your chip to run stable at 2.4ghz? seems too high to me. Also its safer to set CPU startup to "Startup" (i see you have it set to 1.500v), and I'd suggest keeping voltage at 1.55vcore and VID Special set to auto (so 0%) for a total of 1.55vcore. This is still pretty high and you might want to lower it if you're stable because it shortens chip life.

 

Don't need chipset voltage to be 1.7, you can decrease it to 1.5. And LDT voltage doesnt necessarily need to be 1.3v, it can stay at 1.2v but 1.3's not hurting anything.

Your ram voltage looks OK though as you're running at 240mhz with those chips.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×