Jangor Posted December 6, 2005 I am using an older enermax psu with 465 Watt and the old atx 20-pin connector with a 20-24 pin adaptor. I connected this psu to my mainboard at all 4 points, and with my current configuration it is running well, ocd at 2400 and stable under prime, superpi occt, etc, so I was using it with confidence, until i noticed in speedfan that the -12 rail is only at -9! :confused: Is it a bug in speedfan/the bios, or is the PSU the culprit, just too weak/broken/not good with adaptor? And anyway, what is the -12v rail for? Is it important? Why does it run at all so much out of spec!? Thanks for any suggestions, I thought this psu is still good but now I am wondering if I should get a new one. Quote Share this post Link to post Share on other sites
mattjw916 Posted December 6, 2005 spending good money on a system and sticking a cheap power supply in there just doesn't make any sense IMHO... get a decent PSU, esp since DFI boards can be kinda fussy Quote Share this post Link to post Share on other sites
adamb2k5 Posted December 6, 2005 I have a PC Power & Cooling TurboCool 510. With my DFI NF4 SLI-DR Everest did not show me anything for -12v that I can remember, and if it did there was nothing that stood out for me to be concerned about. However, I just replaced my motherboard with an Abit KN8 SLI and Everest is reporting my -12v to be -6v. I would be very surprised if this power supply was bad. I'm going to have to try another one tonight. This power supply should be able to handle my system perfectly and then some. Quote Share this post Link to post Share on other sites
adamb2k5 Posted December 6, 2005 Can someone else try the new version of the trial everest ultimate edition and tell me what is your -12v and -5v at? Quote Share this post Link to post Share on other sites
Dave_Sz Posted December 6, 2005 Everest doesn't show my -5v or the -12v. Quote Share this post Link to post Share on other sites
Dave_Sz Posted December 6, 2005 Everest doesn't show my -5v or the -12v. Quote Share this post Link to post Share on other sites
mrlithium Posted December 7, 2005 i just got my Lanparty today, and speedfan shows -9.40v on the -12v line and I have an antec truepower 2 -550watt power supply which seems pretty good to me. So i think its just somthing with speedfan. Quote Share this post Link to post Share on other sites
n_w95482 Posted December 7, 2005 MBM5 shows -9.6 volts for the -12v rail and -0.72v for the -5v. I haven't tried checking it with Speedfan lately. My PSU is listed below. Quote Share this post Link to post Share on other sites
-CsA-TAZ Posted December 7, 2005 Use Smartguardian! should be on the CD that came with the DFI MoBo! Quote Share this post Link to post Share on other sites
M_M Posted December 7, 2005 Check what the BIOS is saying... Quote Share this post Link to post Share on other sites
adamb2k5 Posted December 7, 2005 Weird, BIOS doesn't show me anything for the negative rails. BTW I am using an Abit KN8 SLI right now. Not sure if I am going to switch back to the SLI-DR. The chipset on this one runs much cooler in SLI mode and my computer doesn't sound like a whirlwind anymore. Quote Share this post Link to post Share on other sites
SageI Posted December 7, 2005 If I am not mistaken. -12 and -5 volts are no longer used. As far as I know the last mobo that used these voltages are at least 5 or more years ago. If I am not mistaken they were used on the early eaproms (BIOS). eaprom (Electronicaly alterable program read only memory) or earom just leave out the program. Quote Share this post Link to post Share on other sites