tatts Posted December 1, 2005 Posted December 1, 2005 i use a DD maze4 and cant fault it can you 2 put results in here please http://www.dfi-street.com/forum/showthread.php?t=32527 Share this post Link to post Share on other sites More sharing options...
adsusanto Posted December 1, 2005 Posted December 1, 2005 I been reading through the A64 OC Guide in the last few day, been testing my X2 4400+ for the CPU MAX and I can only get to FSB/HTT 227, 2.5Ghz.I'm using water cooling for my Cpu and Gpu, Temps is around 48-51C when full load and Vcore 1.64! I would like to know that if I can get higher CPU Max for my 4400??? Or that's really the max for my CPU??? Do I need better water cooling system or should I add more Voltage for my CPU??? Can anyone help me out on overclocking my CPU, I'm new in overclocking that's y I've got so many questions to ask, hehe!! Plx help me out!!! I'm stuck!! Thanks very much to everyone!!! Dude 2.5Ghz is good enough...the 4400+ will get at least 2.5 up to 2.7Ghz on water if you are lucky. Forget about higher speed than that even if you got the best memory on the planet! You will need an extreme phase cooling for that. The only thing I am worried is your temp! It is much too high for water cooling. Even mine running the same voltage...the max it will hit is 45C (rarely though). Share this post Link to post Share on other sites More sharing options...
Pyr0 Posted December 1, 2005 Posted December 1, 2005 i'm at 2816MHz (256x11) so far temps are just touching 42C under load (2x folding@home) i just have the standard swiftech apex kit @tatts, what ramsinks do you have on your BFG7800 memory? Share this post Link to post Share on other sites More sharing options...
BlackEyedBoy Posted December 1, 2005 Posted December 1, 2005 I was thinking........ my temps are too high(34, 49-52load).........with watercool.......voltage too high as well(1.64)..........hum................ is this because I'm using the ATI RDX200 Motherboard???? Does it matter????? id I get the worng Motherboard?????? Share this post Link to post Share on other sites More sharing options...
adsusanto Posted December 1, 2005 Posted December 1, 2005 I was thinking........ my temps are too high(34, 49-52load).........with watercool.......voltage too high as well(1.64)..........hum................ is this because I'm using the ATI RDX200 Motherboard???? Does it matter????? id I get the worng Motherboard?????? I really dont think it is because the chipset difference....maybe check your water block connection?? do you put a good quality thermal paste on it??? By the way what is your chipset and PWMIC temp??? Try not to get above 50C for both of them... Share this post Link to post Share on other sites More sharing options...
tatts Posted December 1, 2005 Posted December 1, 2005 @tatts, what ramsinks do you have on your BFG7800 memory? ive just put some zalman ones on it @ blackeyedboy, what WC kit have you got & what are your ambient temps? Share this post Link to post Share on other sites More sharing options...
YYZ2112 Posted December 1, 2005 Posted December 1, 2005 I'm a novice at this but last night using Angry's OC tutorial on finding highest CPU fsb (mem divider at 1/2), I found that I couldn't get past 213 (low I know) in SuperPI at 1.5v until I went down to 1.475v which has passed at 220 so far. Does this seem right....undervolt results in better CPU stability. Should the path I'm going down (undervolt) have negative consequences after finding my RAM top FSB and then negotiating the best of the two (RAM and CPU FSB)? Thx. Share this post Link to post Share on other sites More sharing options...
BlackEyedBoy Posted December 2, 2005 Posted December 2, 2005 I'm using a zalman water cooling block and I use the coolermaster thermal paste. PWMIC aroung 40C and Chipset around 46C!!! Maybe I should redo the CPU Block and see if it is the water block connections!! Share this post Link to post Share on other sites More sharing options...
divinemisfire Posted December 2, 2005 Posted December 2, 2005 I'm a novice at this but last night using Angry's OC tutorial on finding highest CPU fsb (mem divider at 1/2), I found that I couldn't get past 213 (low I know) in SuperPI at 1.5v until I went down to 1.475v which has passed at 220 so far. Does this seem right....undervolt results in better CPU stability. Should the path I'm going down (undervolt) have negative consequences after finding my RAM top FSB and then negotiating the best of the two (RAM and CPU FSB)?Thx. Thats weird .. i dont think so. U should get at least up to 227x11 with that voltage. 2.5GHz is basically what most of 4400+ will at least get before things started getting harder to tweak. Share this post Link to post Share on other sites More sharing options...
divinemisfire Posted December 2, 2005 Posted December 2, 2005 I'm using a zalman water cooling block and I use the coolermaster thermal paste. PWMIC aroung 40C and Chipset around 46C!!! Maybe I should redo the CPU Block and see if it is the water block connections!! How does pwmic and ur chipset got anything to do with the cpu waterblock ? u watercool ur chipset as well(not on ur sig). ? Additional fans on both area should help the temps. Hows the weather in HK ? .. how bout ur ambient temps ? Share this post Link to post Share on other sites More sharing options...
BlackEyedBoy Posted December 2, 2005 Posted December 2, 2005 I didn't watercool my Chipset and Pwmic, just letting you know the temps of it!! Weather in HK is around 22-26 Share this post Link to post Share on other sites More sharing options...
BlackEyedBoy Posted December 2, 2005 Posted December 2, 2005 Oh sugar, I just realize that I've got my water cooling setup wrong, maybe thats the reason my temp are so high!!!! From water tank - pump - Reserator - cpu - gpu - back to tank!! haha.......... Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now