Jump to content
Sign in to follow this  
Edeka

Need BIOS advice...

Recommended Posts

Hey all. My chipset fan died a few days ago, and I replaced it with a Vantec Iceburq fan from newegg. For some strange reason, my BIOS reset when I did this, so I need to redo them all.

 

Can anyone provide a link to some pictures or a list of good BIOS settings for my system? My computer specs are in my sig.

 

I'm using the 6/23 BIOS, and I would like my CPU fairly overclocked (stock 2.2Ghz, O/C at 2.5Ghz or so), and memory as well.

 

I don't know much about BIOS settings, so a list or some pictures that would work with my system would be great.

 

Thanks!

Share this post


Link to post
Share on other sites

Hey

 

I'm using these for my Venice 3500+ and same Ram stick's as yours.

240x11/2640 mhz.

 

 

Genie BIOS Settings:

 

FSB Bus Frequency - 240

LDT/FSB Frequency Ration - Auto

CPU/FSB Frequency Ratio - 11

PCI eXpress Frequency - 100Mhz

 

CPU VID StartUp Value - 1.500v

 

CPU VID Control - 1.300v

CPU VID Special Control - Avove VID * 110%

LDT Voltage Control - 1.40v

Chip Set Voltage Control - 1.70v

DRAM Voltage Control - 2.80v

 

DRAM Configuration Settings:

 

DRAM Frequency Set - 200 (DRAM/FSB:1/01)

Command Per Clock (CPC) - Enable

CAS Latency Control (Tcl) - 2.5

RAS# to CAS# delay (Trcd) - 03 Bus Clocks

Min RAS# active time (Tras) - 08 Bus Clocks

Row precharge time (Trp) - 03 Bus Clocks

Row Cycle time (Trc) - 13 Bus Clocks

Row refresh cyc time (Trfc) - 17 Bus Clocks

Row to Row delay (Trrd) - 03 Bus Clocks

Write recovery time (Twr) - 03 Bus Clocks

Write to Read delay (Twtr) - 02 Bus Clocks

Read to Write delay (Trwt) - 03 Bus Clocks

Refresh Period (Tref) - Auto

Write CAS Latency (Twcl) - Auto

DRAM Bank Interleave - Enabled

 

 

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - Auto

DRAM Data Drive Strength - Level 2

Max Async Latency - 8.0 Nano Seconds

DRAM Response Time - Normal

Read Preamble Time - 6.0 Nano Seconds

IdleCycle Limit - 256 Cycles

Dynamic Counter - Disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(4 Bursts)

 

Good luck.. :)

Share this post


Link to post
Share on other sites

A good resource for OC settings is the overclocking Database. It is full of tested stable settings for all kinds of setups. Browse through it and see if any of them are close to your system specs.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...