Jump to content
Sign in to follow this  
Jesus

Board refuses to work w cas 2,5

Recommended Posts

As soon i select CAS 2,5 in the memory menu with whatsoever settings teh Board Posts but nothing after that. I cant't get into BIOS, if i don't try to enter bios i get just blue or white smileys or this mark !!!!!!!!!!!!!!! in various colours.

 

Using 6/23-1 beta bios from Techpowerup.

 

Tried just one stick does not help. This problem existst since i bought the board.

 

tried all four slots No go!

 

Ideas?

:confused: :confused:

Share this post


Link to post
Share on other sites

Hello.

 

In the BIOS Genie settings >Dram configuration

 

Press F7 to load optimised defaults

Then change only the CAS latency to 2.5

Save & Exit

 

What happens?

Share this post


Link to post
Share on other sites

I had two sticks 512 PdP Memory did the same thing. RMA'd the memory and the two sticks they sent back worked FINE...

 

RGone...

 

cas 2 works. Cas 2,5 does not work with any bios, cas3 board does not post!

Share this post


Link to post
Share on other sites
Hello.

 

In the BIOS Genie settings >Dram configuration

 

Press F7 to load optimised defaults

Then change only the CAS latency to 2.5

Save & Exit

 

What happens?

 

Post, white or blue smileys or exlamation marks, restart.

over and over and over again.

I can't get into bios, on th e left top corner there's just a blinking cursor.

 

With CAs 3 Board does not Post.

Share this post


Link to post
Share on other sites

Might be due to the other timings, what are they?

 

Try this

GENIE BIOS Setting

>DRAM Configuration..................Press Enter = New Menu

FSB BUS Frequency....................200

DRAM Voltage Control.................2.7v

 

GENIE BIOS Setting >DRAM Configuration

DRAM Frequency Set (MHZ).............200 (DRAM/FSB:1/01)

Command per clock (CPC)..............Enabled

Cas latency (tCL)....................2.5

RAS to CAS delay (tRCD)..............3

Min RAS active time (tRAS)...........7

Row precharge time (tRP).............3

Row cycle time (tRC).................11

Row refresh cycle time(tRFC).........14

Row to Row delay (tRRD)..............2

Write recovery time (tWR)............3

Write to read delay (tWTR)...........2

Read to write delay (tRWT)...........2

Refresh period (tREF)................AUTO

Write CAS latency (tWCL).............1

DRAM Bank Interleave.................Enabled

 

DQS Skew Control.....................Decrease Skew

DQS Skew Value.......................0

DRAM Drive Strength..................AUTO

DRAM Data Drive Strength.............AUTO

Max Async Latency....................6ns

Dram Response........................Normal

Read Preamble Time...................5ns

Idle Cycle Limit.....................AUTO

Dynamic Counter......................Disabled

R/W Queue Bypass.....................AUTO

Bypass Max...........................AUTO

32 Byte Granularity..................Any setting

Share this post


Link to post
Share on other sites
I had two sticks 512 PdP Memory did the same thing. RMA'd the memory and the two sticks they sent back worked FINE...

 

RGone...

 

 

Me too... I had some 3200rev's that would NOT run anything but cas2 and this was tested on 2 different mobo's..

 

Jesus.. Do you have another system to test them on ?

Share this post


Link to post
Share on other sites

@THunDA

no unfortunatley not , had to sell my old Socket A rig to be able to buy this. Tommorow a pal of mine will lend me his Kingmax Hardcore 466 SPD 2,5-3-3-7 and we'll see i f its the board or my memory.

 

@wakeup which board revision do you have? R.AA0 R.A20 R.A30 R.AB0?

it's written on the sticker thast on the side of the second PCI-e slot.

Share this post


Link to post
Share on other sites

I never got CAS 2,5 work either. Only CAS 2 seams to work with my RAM ... No biggie for me, as long as it's stable (which it is).

 

Kind regards,

Karl

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

×
×
  • Create New...