LanParty NF4 BIOS - Cleaned up 704-2bt a little

[Guest Fubar]

Hello,

 

as you can see in my Sig right now I am running Standard all the way.

 

The next couple'a days I'll have some time to kill.

This rig was bought to be overclocked.

 

Will the 704-2BTA work fine with my Hardware?

Is there also a way to flash it the old fashion way with a floppy?

 

Since my H²0 is pretty good I'll guess I could reach the 3,2 Ghz with my CPU. It is pretested till 3ghz with air cooling.

[Guest caffeinejunkie]

Im assuming the mem is tccd so the 704-2bt should be perfect

 

i used it for a while but switched around a bit and landed on the 3/29/06

[Guest Fubar]

I changed my Signature. Made a mistake. Don't have 3200. I got PC-4000 running at 2-3-3-3-7.

 

According to this page there is a chance that I do not have TCCD.

 

http://www.xtremesystems.org/forums/showthread.php?t=50010

 

What to do?

 

I really do not feel like removing the headspreaders.

[Cantras]

I have pretty much the same System including the same RAM.

 

Does anyone have an idea how to check if the chips on the DIMM are TCCC, TCCD or BH ?

 

Bye, Cantras

[Guest Fubar]

Is there a thorough Explanation of every BIOS Setting? Preferably this 704-2BTA ?

 

Maybe with recommendations etc.

 

I would like to have some sort of Guide in order to tune the heck out of my system.

[THunDA]

The best you will get is the overclocking guide stickied in the overclocking forum..

[Uber-Noober]

From my sig, this is the best I can do with my Overclock using the 6-23 BIOS. (E3 Venice)

 

However, I know with my cooling and power supply I should be able to get at least 2700 MHz. Many others have managed to get this mark with Venices and OCZ Plat Rev.2 .

 

Do you think I should give this BIOS a try or is 2500 MHz the peak of all peaks for my system. I have a fleeting hope that the memory divider "bug" I have is most likely fixed with this 7-04BTA BIOS.

 

SO folks? WHat you think 6-23 or 7-04BTA? Your opinions I take seriously....

[red930]

Have you checked the OCDB for a similar setup as yours?

[Dutch Guy]

Recently I bought 2Gb of OCZ gold XTC PC3200 but the SPD is 2.5-3-3-8 and the label on the sticks says 2-3-2-8 which is correct and should i use with the 704-2bta BIOS?

[Nil Einne]

The label is correct. The SPD is sometimes set higher to avoid possibly problems with some mobos/configs. However if you RAM is rated at 2-3-2-8 then it should run at 2-3-2-8 and if not, you should be entitled to RMA it. Make sure that OCZ doesn't rate the RAM differently for AMD

[dbius]

Hi Guys!

 

I don't understand it clearly, so THIS bios can use with EVERY DFI NF4 board? (with expert and venus too??? :confused: )

 

THX!

 

dbius

[soundx98]

No, not the Infinity boards.

There is a different version for the Expert boards.

There is no Version for the Venus.

But yes it is for all The LanParty NF4 boards including SLI and SLI-DR versions.

 

I'd suggest the 03/29/2006 or later for the Venus.

Don't flash if you have no issues.

(727 is a kewl number)