Jump to content

WoZZeR

Members
  • Content Count

    7
  • Joined

  • Last visited

About WoZZeR

  • Rank
    New Member
  1. not sure but i think the stepping you may be on about is in this pic from cpuz: also using water cooling THERMALTAKE AQUARIUS 3
  2. ok bought and installed a thermaltake wo131 850w what would be the next stage with my settings at the moment: Genie BIOS Settings: FSB Bus Frequency............................. - 290 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.350V CPU VID Special Control....................... - 102,4% LDT Voltage Control........................... - 1.20v sb pcie ...................... - 1.8v nb asnalog ................. - 1.2v nb core .....................- 1.2v DRAM Voltage Control.......................... - 2.80v DRAM Configuration Settings: DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 08 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 9.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.0 Nano Seconds IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(8 Bursts)
  3. just go into bios and change the boot priority like Raiderfan001 said to your current harddrive with windows on
  4. ok here is what i have tried at the mo: Genie BIOS Settings: FSB Bus Frequency............................. - 290 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.350V CPU VID Special Control....................... - 102,4% LDT Voltage Control........................... - 1.20v sb pcie ...................... - 1.8v nb asnalog ................. - 1.3v nb core .....................- 1.3v DRAM Voltage Control.......................... - 2.71v DRAM Configuration Settings: DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 08 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 9.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.0 Nano Seconds IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(8 Bursts) these setting are for a manchester 4200+ x2 mine is a toledo cpu if that matters??? these settings bsod my pc when playing battlefield 2 tried this: Genie BIOS Settings: FSB Bus Frequency............................. - 290 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.350V CPU VID Special Control....................... - 102,4% LDT Voltage Control........................... - 1.20v sb pcie ...................... - 1.8v nb asnalog ................. - 1.2v nb core .....................- 1.2v DRAM Voltage Control.......................... - 2.9v DRAM Configuration Settings: DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 08 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 9.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.0 Nano Seconds IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(8 Bursts) this ran battlefield 2 on single player for about 5mins the screen went black and sent me to visya desktop where the game had been stopped and not running or showing on vista. so i changed to this: Genie BIOS Settings: FSB Bus Frequency............................. - 290 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.550V CPU VID Special Control....................... - auto LDT Voltage Control........................... - 1.20v sb pcie ...................... - 1.8v nb asnalog ................. - 1.3v nb core .....................- 1.3v DRAM Voltage Control.......................... - 2.6v DRAM Configuration Settings: DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 08 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 9.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.0 Nano Seconds IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(8 Bursts) this ran ok for a while then started to get a bit jerkey in battlefield 2 i am running my gainward bliss 512mb 7950 gt with ati tools 0.27 beta core 653mhz mem 883mhz with latest vist 32bit nvidia driver 158.24_forceware_winvista_32bit_english_whql did choose and install 158.24_forceware_winvista_32bit_international_whql for u.k where i live but had trouble installing it as it would not detect the software ect.. in install the driver to my graphics card. teps i am getting idle are cpu 37c pwmic 39c chipset 51c can anyone see anything wrong with these settings for getting my pc running nice and smooth?
  5. just ran prime95 and got this error not very good understanding this program so any help on getting max speeds for my system would be great
  6. hi all, Im very new to all this so please bare with me lol. my setup is follows: 450watt psu not a cheap'o one lol OCZ Gold 2x 1 GB PC4000 DDR500 RAM AMD ATHLON 64 X2 4200+ 4.4 GHZ 1MB 939 DUAL CORE (TOLEDO CORE) Gainward Bliss nVidia 7950GT 512MB Dfi LANPARTY UT RDX200 CF - DR MOTHERBOARD latest bios update RDXDC23 THERMALTAKE AQUARIUS 3 WATERCOOLING I have got it running at 2.97ghz and when i tried battlefield 2 it crashed. i am currently running it at 2.91ghz and memory running at ddr529.8 but battlefield 2 seems a little jarky sometimes. i know i really should have a very good read through all the thread stickeys ect... but thought i would cut all the reading short and ask one of you experts and getting my setup fine tuned as i think i may have my memory timing slightly wrong or something? I am sure this cpu could do 3.0ghz my memory setup in the bios is this: 200mhz/fsb :01/01 cpc - auto tlc - 3.0 trcd - 04 tras - 08 trp - 03 trc - 11 trcf - 16 trrd - 03 twr - 03 twtr - 02 trwt - 03 tref - 3120 dram blank interleaving - enabled dsq skew control - auto dsq skew value - 0 dram drive strength - level 8 dram data drive strength - level 2 (reduced 30%) max async lantency - 8.0ns read preamble time - 6.0ns idlecycle limit - 256 cycles dynamic counter - disable r/w queue bypass - 16x bypass max - 7x 32 byte granularity - dissabled (8 bursts) my cpu. ldt / fsb - x4.0 cpu vid - 1.550v dram - 2.6v sb pcie - 1.8v nb analog - 1.3v ldt bus - 1.5v nb core - 1.3v if anyone could give me any help if these settings are wrog and for me to get the most out of my setup stable for running games i would be very grateful.
×
×
  • Create New...