Jump to content

Wild Thing

Members
  • Content Count

    141
  • Joined

  • Last visited

Everything posted by Wild Thing

  1. Did you run wd's hdd diagnostic program? Did you set raptor as first bootable hard drive?
  2. Update your sig as per the rules, so hg or a mod wont give you a 7 day vacation. Have you run memtest at stock speed? Check out the stock speed data base for a system similar to yours and try those settings and there's a 165 data base also. Post your memory settings.
  3. Sorry about my bad manners. Welcome to the Street.
  4. Try a short cmos clear about 5 min. should do, then load optimized defaults and ram timings if needed.
  5. Did you clear Cmos and load optomized defaults after flashing?
  6. Could be your psu. It is on the psu to avoid list, http://www.dfi-street.com/forum/showthread...light=psu+avoid. Do you have a friend that you could borrow a power supply to try? Dfi NF4 boards are picky about psu's. Here is a list of recommended psu's, http://www.dfi-street.com/forum/showthread.php?t=10854
  7. Your problems are probably related to your power supply. Minimum power requirements for dfi nf4 boards are 480w and 24-pin connector. Do yourself a favor and get a power supply that is on the recommended list: http://www.dfi-street.com/forum/showthread.php?t=10854 Under powered dfi nf4 can cause alot of problems and can cause hardware damage.
  8. Try the Dram Drive Strength at 7 and leave everything else as is.
  9. Try these settings with 2 sticks of ram in the orange slots. DRAM Frequency Set............................ - 200 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 7 DRAM Data Drive Strength...................... - 3 (Reduce 15%) Max Async Latency............................. - 8.0 Nano Secjonds DRAM Response Time............................ - Fast Read Preamble Time............................ - 6.0 Nano Seconds IdleCycle Limit............................... - 016 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16x Bypass Max.................................... - 04x 32 Byte Granularity........................... - Disable(4 Bursts)
  10. HappY-Games and Momma, What exactly do you two do for DFI to get paid for it?
  11. Here are some links that might help. Initial build with pictures http://www.dfi-street.com/forum/showthread.php?t=20832 overclocking guide http://www.dfi-street.com/forum/showthread.php?t=20823 Psu guide http://www.dfi-street.com/forum/showthread.php?t=10854 memoy guide http://www.dfi-street.com/forum/showthread.php?t=24719 If money is tight you can try ebay. A lot of people at this forum hate ebay. But, you can get some good deals. I got my ram for $150, retail $240, psu $40 retail $90, ultra-d $50 retail $129. But it took me 6 months to get these items.
  12. Kingston ram is know not to work with DfI boards. and minimum requirements for a psu is 24 pin , 480 watts. There are 4 power inlets on the NF4 Ultra-D, 24 pin, 4 pin, molex, and floppy. All of these must be plugged in. I have followed the new build guide, overclocking guide, and anyother recommendation that I can find on this forum. I have had no problems with my build. I truely believe if you follow the experts opinions and recommendations on this forum you problems will be minimal. I am new to DFI, 3 months.
  13. Memtest does not stop checking memory. It gives you an error count. You sould not have any errors for a mimimum of 8 hours. If you do you should tweek your ram. and run memtest again. You really should consider getting better ram and powersupply. As the ram and/or psu that you have can give stability problems.
  14. On the NF4 Ultra-D 3 & 4 are the Nvidia ports
  15. My SI-120 with 104 cfm panaflo fan keeps PWMIC at 28 unloaded and 38-40 loaded.
  16. try Gary Headlee at http://www.motherboardrepair.com he repaired some cpu pins for soundx98.
  17. AMD Opteron 144 Venice 2x1GB OCZ Gold Edition 1GB PC-4000 OCZ5002048ELGE-K (UCCC) Biostar GeForce 6500 256MB , 400/532 8.1.9.5 drivers Maxtor 250GB IDE hdd (8MB cache) WD 250gb sata II hdd (16MB cache) ========== Genie BIOS Settings: FSB Bus Frequency - 290 LDT/FSB Frequency Ratio - X3 CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.450v CPU VID Control - 1.325v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.60v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clock DRAM Bank Interleave - Enabled DQS Skew Control - Increase Skew DQS Skew Value - 0 DRAM Drive Strength - Level 6 DRAM Data Drive Strength - Level Auto Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 7.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: 3dMark2003: 3dMark2005: ========== short description: 290x9 @ 2610Mhz, 1.325v + 113% 3-4-3-7 @ 2.6v vdimm
  18. try a more powerful psu. dfi boards require a minimum of 480 watts. if you have a different psu or know someone you can borrow a psu from. if not check here for recommended psu http://www.dfi-street.com/forum/showthread.php?t=10854 I would recommend you get a psu with a minimum of 480w.
  19. yes you can use the X2 cpu. there are 4 power connectors on SLI-D 24-pin, 4-pin, molex, and floppy.
×
×
  • Create New...