Jump to content

Asmodeo

Members
  • Content Count

    4
  • Joined

  • Last visited

About Asmodeo

  • Rank
    New Member
  1. palehorse, I suggest that you try, if possible, to clean-up the poll from data related to non-expert board. Maybe this will help to make the importance of the issue more clear Here below my data Please take into account that my DigitalDoc 5+ temp sensor placed a side to the IHS reads 27C in Iddle and that my rig is OC'd (see http://www.dfi-street.com/forum/showpost.p...8&postcount=148) What choice did you make in the poll above? I believe mine is 10-20C low. Motherboard: SLI-DR Expert Mobo Revision: ??? Mobo BIOS version: 12/7 Official CPU: AMD Athlon 64 3700+ San Diego CPU ID: ??? Idle Temp: 16C Cooling: Water Bye Asmodeo
  2. No one of the staff member would like to comment the first OC of a poor DFI Rookie Thanks Asmodeo
  3. Thanks Voltes-5, Yes this is exactely the block I'm using, it's made here in Italy, but I don't know if they have a retailer in US. Why don't you email them Asmodeo
  4. I've just added my overclock to the database http://www.dfi-street.com/forum/showthread...1318#post401318 First of all I hope it's compliant with the rules, I've done my best Then, any comment, question or suggestion are more then wellcome Thanks Asmodeo
  5. UT nF4 SLI-DR Expert - 12/07/05 BIOS AMD Athlon 64 3700+ San Diego 2x512MB G.Skill F1-4800DSU2-1GBFF PC4800 Sapphire Radeon X800 GTO² 256mb PCI-E x16 @X850 (500Mhz/600Mhz) - Omega Driver 3.8.205 2x Hitachi Deskstar t7k250 200gb SATA-II (NVIDIA RAID-0) PLEXTOR DVDR PX-750A LG DVD-ROM GDR8163B OCZ PowerStream 600 DigitalDoc 5+ Fully Water Cooled by OCLABs MonoBlock Series * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 285 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - x10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.425v CPU VID Special Control - Above VID * 112% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.52v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 + SmartGuardian: SmartGuardian CPU Temp is not accurate at all. The DigitalDoc 5+ sensor Temp is 27C 3dMark2003: 3dMark2005: 3dMark2006: Everest Ultimate Edition: ========== Short Description: 285x10 @ 2850Mhz, 1.425v + 112% 2.5-4-5-3 @ 2.80v vdimm
×
×
  • Create New...