Jump to content

mrtell

Members
  • Content count

    102
  • Joined

  • Last visited

About mrtell

  • Rank
    Member
  1. mrtell

    VENUS motherboard

    Wondering if i want to sell my VENUS motherboard. Hardly used and never flashed, only ever had opteron 144 in the board and only run it at 2.6, never raised the voltage even. What is the board worth??? UK
  2. I am fairly new to overclocking and would like some opinions. Opteron 144 1.8 All I did was set Bios to optimized defaults, Set FSB to 300, LDT to X3 Dram to 166 Divider, cpu = 2.7 Then ran Prime, 1 pass, priority 5, small FFTs. no probs. Thing is I have no prog to monitor temps, speed fan caused my PC not to boot and even a cmos clear would not correct, had to reformat lol. I have heard MBM5 is good, any issues? how accurate is it? and how much lower does the board read temps than actualy are. I assume now the hard work starts and theres a lot that can be done to reach higher clocks.
  3. mrtell

    Cpc

    anyone?
  4. mrtell

    Cpc

    So, set to Optimized Defaults, leave everything else, and just raise Front Side Bus. I have a 9X opteron that will clock to at least 2.7 which means going to 300 FSB, my memory which is PC 4000 wont go that high so I will have to use dividers, is it better to go as close to the max of my memory with dividers if you know what I mean? Oh, and thanks.
  5. mrtell

    Cpc

    I have read that memory placed in slot 2 and 4 are locked at 1T ( no need to set at 1T ). Is this correct? Also would it be better to set at 2T just to get higher clock at synchronous with cpu? I also read that it is better to run at 1T but with dividers and push cpu as high as possible. And one last question, Whan i had my none DFI board the PCI / AGP was locked so it would not raise at the same time as the FSB, Is the same locked on the DFI boards? thanks
  6. In the Bios, CPC setting, If on auto, what are the parameters for its selection. Or a simpler question, if I want 1T or 2T I just set as such?
  7. Just installed speedfan, disaster! When speedfan was Configuring PC shut down instantly,when I rebooted there was no display, reset Bios still no display, I had to reformat and reinstall windows, no way I am going to use speedfan again.
  8. mrtell

    Karajan audio

    Ok, will go do that, thanks
  9. New build. Is the Audigy 2 better than the Karajan audio? Is it better to uninstall the Karajan audio modual or just leave it in place and cancell in the Bios? Is smart guardian better than speed fan? thanks
  10. mrtell

    cpu fan temps

    Once the sides are on the case and I overclock the cpu that should raise the cpu temps. Or like has been said just connect direct to power supply. Just worried me a bit at first when the fan did not spin and I did not know how much the boards temp was being miscalculated.
  11. Just done a partial build with a freezer 64 pro heatsink/fan. fan does not spin because the temp according to the bios is 22 and i cannot lower the setting for cpu fan shutdown less than 25 so fan will not spin. This would be fine if the board read the temps correctly but as I am always being told the board reads the temps way out. Any suggestions please. Also how far are the temp readings out and is one venus just the same as any other Venus where temp readings are concerned? thanks
  12. mrtell

    sapphire or powercolour

    Was going to buy the Sapphire X1900XTX but sold out at the moment, so was wondering what the Powercolour is like instead? or even the Asus. any opinions?
  13. mrtell

    Chipset Fan???

    http://www.angrygames.com/chipset_clean-1.htm
  14. Got my Venus today, opened packet to find the catch fell off the box and the top of the box is bust on 2 corners lol, but not crushed and it is only a box. Looking forward to building. Floppy cable works.......(on my abit anyway) bent jumper pin on the audio, will it bend back without breaking?
×