Jump to content

noahsark1126

Members
  • Content count

    212
  • Joined

  • Last visited

About noahsark1126

  • Rank
    Member
  1. noahsark1126

    The AMD 3GHz Club

    Kanzleramt has a 3800+ Venice. It's not an X2. I was pretty confused at first too lol.
  2. Thanks for the help everyone. The test passed, it booted into safe mode, and then it booted into regular startup (thought it did act a bit strange). I got the files I need off the hard drive and I think I'll do a clean install of XP tomorrow (unless it seems to be functioning completely normally, which right now it isn't). Thanks again.
  3. Good idea about Tmods cd. I am running a WD diagnostic test as I write this. I'll see what happens and I'll also try safe mode.
  4. No, the BSOD just flashes for a split second, I cannot read it at all. I don't have another computer right now (all the other computers in my house are notebooks, and I don't think I can hook my SATA drive up to a notebook can I?) I will probably be able to find some computer or other to use, maybe a friend's or a neighbor's. As for WD Lifeguard, I don't even have that installed on the computer. Any other ideas?
  5. I have Windows XP Home, running on a A64 x2 4200+ and 2gb of OCZ low-latency platinum RAM. I had a stable overclock, seen in my sig, and everything was working fine until today. Now, when Windows starts up it seems to be fine but then a few seconds later I will get a BSOD and the system will restart, repeating the whole process. This is what I have done: -set everything back to stock settings -tried removing a stick of ram, tried the other one, switched them around in the 4 slots -ran memtest, and got no errors What is the problem here? I really need this computer to work, and it is obviously not my hardware. Is there some way windows can get messed up to cause this? Can I fix it? What should I do?
  6. noahsark1126

    new water cooling

    I think it just might be doable. It might take some case modding, but it'll save me the $100+ for a new Full Tower case. It will also allow me to have a rad in between the two heat sources, the CPU and GPU. The only disadvantage I see (besides the obvious need for more tubing) is that two 120 rads is much more expensive than one 240. It's ok though because I am way under my budget anway. As for the reservoir, I will take lowboy's advice and read around about them. I can do a fillport if i have to.
  7. noahsark1126

    new water cooling

    Actually, my case has three 120mm fan mounts - one each in the rear, front, and side. Right now there are actually fans in those slots, but I could definetely put some radiators there. And there is more space than you think; it's one of the larger mid-towers out there. My desk has a nice spot for a computer case, which I use, but a full tower wouldn't fit, that's why I got a medium one. As for the reservoir, is it better to get the cylindrical one or a bay style? I have 4 free 5.25 bays which I could use.
  8. noahsark1126

    new water cooling

    You're right, there is definetely not enough room anywhere in my case for a radiator. The black ice is 292mm x 133mm x 29.6mm which is about equal to 11.5in x 5.2in x 1.2in (and is meant to hold 2x120mm fans, obviously, which adds even more to the thickness). I don't have anywhere near that kind of space. So that means I either have to buy a new case (ouch) or put the rad outside the case. There really isn't a good place on the actual outside of the case either, so that means I would need to put it somewhere farther away, which means much more tubing. Can I do that? I'll look into the reservoir instead of fillport/t-line idea. I would really rather not drill holes in my case, but I will if I have to.
  9. noahsark1126

    new water cooling

    Am I going to have to drill a hole in the top of my case for the fillport? I don't think I have a drill to do that with. That's what Danger Den says you should do, and it also says to drill a hole for a fan and rad in the top. I know I don't have the tools to do that. My case is this: http://www.newegg.com/Product/Product.asp?...N82E16811146013 Is it big enough for everything? Is there a place I can even put the rad? Do I need a new case? And maybe this is a stupid question, but do I need 2 rads? That list I posted before only includes one. Sorry for all the questions, but water cooling is really not my area of expertise.
  10. noahsark1126

    new water cooling

    Ok, here is what I've got so far, taking into account all of your advice. TDX and D5 combo http://www.dangerdenstore.com/product.php?productid=170 low-profile maze4 gpu block http://www.dangerdenstore.com/product.php?productid=161 black ice gts 240 x-flow http://www.dangerdenstore.com/product.php?productid=225 delrin fillport (1/2 OD) http://www.dangerdenstore.com/product.php?productid=244 T (for 1/2 ID tubing) http://www.dangerdenstore.com/product.php?productid=65 12x clamps http://www.dangerdenstore.com/product.php?productid=62 20ft clearflex 60 tubing (1/2 ID and 3/4 OD) http://www.dangerdenstore.com/product.php?productid=61 zerez coolant (4oz bottle) http://www.dangerdenstore.com/product.php?productid=77 total (including discount code and shipping): $216.29 Not bad. That's a lot less than I expected. And I will of course be buying some 120mm fans. I think air cooling is fine for my chipset. Right now it stays below 40 degrees, which is fine with me.
  11. noahsark1126

    new water cooling

    Yea, that's pretty much what I have. I also put some MCT-40 in my list. I need that, right? What fittings do you think I might need? I'm cooling just the CPU and one video card. And how many clamps?
  12. noahsark1126

    new water cooling

    Ok, I got the idea on the radiator. Which tubing do I want, Clearflex or Tygon, and which fittings? (for 1/2in tubing) I assume I want 10ft, correct?
  13. noahsark1126

    new water cooling

    one more question: About the radiators, the stealth gts 240 looks nice, but which one do I get? http://www.dangerdenstore.com/product.php?...1&cat=86&page=1 http://www.dangerdenstore.com/product.php?...5&cat=86&page=1 They appear to be identical except the first one is meant for one fan while the second is meant for two. They are the same price. Which one is better?
  14. noahsark1126

    new water cooling

    Alright thanks for all the quick responses. I pretty much know what to do now. You guys are the best.
  15. noahsark1126

    new water cooling

    Thanks for the advice Miggs. 300-350 is what I was thinking. If I can keep it in that range or lower I will be very happy. The Koosah's are just too expensive. I'll stick with the maze4's. I'll get one of the low-profile ones for now, and if i get a second card I'll buy another. I have some BGA ramsinks for the vid card and I can rig a silent fan to blow on them. As for the rad, the Black Ice does seem like a good choice. But you said I or II depending on my case, how do I know which one? this is my case: http://www.newegg.com/Product/Product.asp?...N82E16811146013 And what about water cooling the chipset? Is that a good idea? there is a danger dan chipset block here: http://www.dangerdenstore.com/product.php?...7&cat=46&page=1 You're right, it is definetely not the Zalman's that are making the noise. That's part of the reason I got them - good performance with low noise (and they do work great for me). It's really my 3x120mm case fans and the NF4 fan that make the noise. I have a fan controller, which has decreased the noise somewhat, but it's still loud enough to be annoying and to stop me from sleeping. I just want the quiet of water. I'll probably take the Zalman's and put them in my old Athlon XP (which is currently on stock cooling -- yuck). There is a link to my case earlier in the post. I just liked the look of it. Is it a loud one? Thanks for all the help.
×