Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by Xolias

  1. It's survived 3 years at that temp, with fan speed at 100%. I'm just gonna let it keep going til it finally dies, it's gonna be obsolete in a few years anyway.
  2. Load Temps CPU: 37C GPU: 90C
  3. What's the best way to do that? Running something like Half Life 2?
  4. remounted, new temps CPU: 24C PWMIC: 43C Chipset: 52C GPU: 68C Huge improvement.
  5. Just installed Smart guardian, fans working much better now. Going to remount all my heatsinks tomorrow. Are there any after market Chipset fans? The nf4 SLI-Dr fan is way loud when on it's fastest speed. Edit: all fans on 100% power. CPU: 1366RPM Exhaust: 1269RPM Chipset: 7337RPM Look good?
  6. But the problem I have is that I don't want my CPU fan ever turning off. but it does when I reach 25C, and it doesn't come back on.
  7. Explain putting salt on your front porch to melt snow if your theory is correct.
  8. What programs should I be using to monitor temperatures/fan speeds? Also is this a good way to control fans? With one of these http://www.newegg.com/Product/Product.aspx...N82E16813999504 Edit: Also, whenever my BIOS turns my CPU fan off for being under 25C it can't seem to boot it back up when it goes back above 25 C.
  9. Much more helpful post than the rest, I'll get on this, thank you.
  10. current temps are 29 CPU 54 PWIM 63 Chipset 82 GPU All Idle Temps
  11. Why would I be complaining if they were F?
  12. Some of my temperatures are getting quite high. My room is usually quite cool but these are some temps... PWMIC: 70* Chipset: 75* Video Card: 125* What can I do about these?
  13. It would be the last few numbers of your serial number on the sticks.
  14. eh... I should have just saved $60 on a heatsink and stuck with stock speeds. Can't figure this stuff out for the life of me.
  15. in my bios there is an option for when the cpu fan turns off completely, and when it is on normal speed, and full speed. Anyway the lowest temp I can go before it turns off is 25, so whenever it gets to 25 it shuts off, then shortly goes on again. Is there a way I can disable it ever turning off? So I don't have to deal with the fan booting down and up all the time, ruining my MBM5 fan speeds and frustrating me.
  16. Right now I'm on 7/04-2BTA BIOS with the optimized settings... Genie BIOS Settings: FSB Bus Frequency - 200 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - AUTO PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Auto CPU VID Control - Auto CPU VID Special Control - Auto LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.6v DRAM Configuration Settings: DRAM Frequency Set - Auto Command Per Clock (CPC) - Auto CAS Latency Control (Tcl) - Auto RAS# to CAS# delay (Trcd) - Auto Min RAS# active time (Tras) - Auto Row precharge time (Trp) - Auto Row Cycle time (Trc) - 12 Bus Clocks Row refresh cyc time (Trfc) - 24 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 DRAM Bank Interleave - Disabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts)
  17. Having trouble OCing. Your BIOS is too different from the SLI-DR one. Is there any other way I can OC this without learning how to OC myself?
  18. Installed it, but I don't know how well. It's running at 27 idle.
  19. Need some help installing this one. Do I need to take my mobo out of my case for installation? Also would I be better off with the big Typhoon or a Zalman?
  20. So do you have to remove the motherobard to install this thing?
  21. up to 40, but I can't buy from newegg because shipping to hawaii is way high. gotta be compusa.
  • Create New...