Jump to content

Pyr0

Members
  • Content count

    483
  • Joined

  • Last visited

About Pyr0

  • Rank
    Member

Contact Methods

  1. Pyr0

    amd x2 4400+ on cfx3200

    the only way to tell is to test it when you say leave the rest at defaults, do you mean the cpu voltage etc? i'm guessing that the chipset voltages etc should be fine at defaults until you start getting up to higher fsb's (i didn't do a lot of clocking with the cfx board, basically chucked it to one side after the ULI fiasco, i'm sick of unfinished boards) i don't have a set of uccc memory, so i can't really advise there, sorry. but generally they should take from 2.6-2.8v
  2. Pyr0

    amd x2 4400+ on cfx3200

    dude, nobody can tell you if your cpu can run at those settings but you personally i wouldn't be giving my memory 3.8v tho i run my 4400 at 250x11 for 2750mhz with 1.40v+12%
  3. a few different versions: http://www.overclock247.com/pyr0/Intel%20SLi/
  4. hmmm... i'd try a fresh install with the vista drivers rather than replacing or updating i've had a cfx3200 sitting here for a couple o months now and just for kicks (boredom) decided to try it out the other day, stripped down my dfi venus and switched boards as soon as windows was installed i began to notice these stupid freezes :confused: i tried installing windows with the 425 bios and the 728 and also tried various versions of the m5288 drivers at the f6 prompt absolutely nothing helped at all :sad: watching films/videos is the worst there's no way i can use this board as part of my main rig in it's current state :mad: needless to say, i've switched back to the venus i might try out those vista drivers sometime, but after wasting my time installing the cfx3200 i'll be buying a couple of spare drives for testing first to save wiping my main install again the board seems ok, stable and such, but the drive controller mess is just taking the p**s
  5. me too, i've got one of these boards on the way :-|
  6. Pyr0

    Razer Copperhead 34.99

    i wish i'd had a better experience with the copperhead i couldn't stand the shape of it (too small and narrow for my hands) and after using it for a month and getting cramps in my hand, it's just a spare mouse i use when fixing other peoples rigs now
  7. i had a tagan 580w easycon for almost a year without problems on a DFI SLI-D, and a DFI Venus i've recently upgraded to the tagan 900w turbojet and it's been great so far
  8. this site's not bad http://www.jab-tech.com/Evercool-VC-RE-Twi...er-pr-2291.html
  9. http://www.jab-tech.com/Evercool-VC-RE-Twi...er-pr-2291.html
  10. such a shame the shop (or rather the staff and customer service) totally sucks hoping to get a dfi infinity 975 myself, but it won't be from there, lol
  11. a lot of people seem to reccomend using arctic ceramique instead of AS5 on GFX cards, ceramique is safer because it's non conductive, and non capacitive i have personally used AS5 on the gfx core without a problem, but never needed to on the memory
  12. http://www.siliconimage.com/support/suppor...&ctid=2&osid=8&
  13. nope, the other one [edit] thanks Lane, although i think the option may not be available in x64 *shrug*
  14. steelballzz, where did you get the little memory app with the skew control?
  15. Pyr0

    The HUGE BIG-BIG Windows Vista Thread

    i use a G7 mouse and found the setpoint 2.60 software installed just fine in vista x64
×