Jump to content

ghoul2oo3

Members
  • Content Count

    19
  • Joined

  • Last visited

About ghoul2oo3

  • Rank
    New Member
  • Birthday 01/29/1984

Contact Methods

  • AIM
    ghoul2oo3

Profile Information

  • Gender
    Male
  1. So I ended up just changing the HT to its default 4x instead of Auto and the Multiplier to 10x since both where on Auto, and it’s seemed to stop. Cold booted fine four times in a row, but if I experience the problem again I'll make sure I reply.
  2. No errors :confused: I wonder if replacing the CMOS battery with a new one would do anything.
  3. Right I'll get straight to my problem, this only started happening yesterday with my nForce 3 chipset. My problem involves cold booting the PC, there will be no audible beep from the speaker and the monitor will stay off but the fans will start spinning as normal. I go to turn it off from the PSU then switch it back on again and it boots up fine. :confused: I've managed to repeat the process, which all result in being able to boot up fine after powering it down again. I can assure you nothing is wrong with my memory modules, as everything runs fine like it has been for the past three months as well as being stable. If your wondering no I haven’t overclocked yet I'm still running stock speeds on both my memory modules and my CPU so basically I wonder if the Antec is too blame here? P.S Antec PSU / DFI NF3 250gb where purchased back in 2005, but the memory modules where purchased a few months back. Any help with this issue would be greatly appreciated.
  4. Note taken Kaxx, perhaps I should just leave VID left on auto?
  5. Thanks for the replies guys I'll look into this, btw is CPU VID Special Control on 126% decent if use 1.5?
  6. Hey guys, I have a question regarding my Socket 754 3000+ Newcastle Core. I wanted to know what would be the best recommended voltage along side a 2.3/2.4GHz increment from the stock 2.0Ghz? I've noticed post lag when I power it up so I believe the CPU isn’t getting enough voltage in order to post as fast as it does with stock speeds. Any help would be appreciated as all I’m after is a voltage recommendation.
  7. As the topic suggests guys, would this kit work on a DFI LanParty UT nVidia nF3 250Gb? It's the TEAM Xtreem PC3200 Poseidon 2-3-2-5 Infineon BE 2GB Kit. Any help on the matter would be greatly appreciated. :nod:
  8. Attempted to go a bit further this time, 2.3GHz as my PC refuses to boot windows at 2.4GHz. At current the full load temp using prime95 scores around 52deg after a few hours and sits between 50-52. Not bad I guess for stock cooling as Idle temps sit around 38-40. Screenshots below... Basically wanted to know from the community again if you think the voltages are looking good enough, but its stable afaik. Genie BIOS Settings: FSB Bus Frequency - 230 FSB AGP Bus Frequency - 66mhz Clock Spread Spectrum - Disabled LDT Downstream Width - Auto LDT Upstream Width - Auto LDT/FSB Frequency - Auto CPU/FSB Frequency Ratio - 10 CPU VID Control - 1.300v CPU VID Special Control - Above VID * 126% Chip Set Voltage Control - 1.60v AGP Voltage Control - 1.50v DRAM Voltage Control - 2.6v
  9. So I've decided to try and aim with 2.2ghz on my 754, but I just wanted to know if these settings are recommended (voltage wise). Reading threw some of the overclocking guides I've come to this conclusion within my BIOS. Genie BIOS Settings: FSB Bus Frequency - 220 FSB AGP Bus Frequency - 66mhz Clock Spread Spectrum - Disabled LDT Downstream Width - Auto LDT Upstream Width - Auto LDT/FSB Frequency - Auto CPU/FSB Frequency Ratio - 10 CPU VID Control - 1.275v CPU VID Special Control - Above VID * 126% Chip Set Voltage Control - 1.60v AGP Voltage Control - 1.50v DRAM Voltage Control - 2.8v My DRAM configuration settings are all on Auto. So I'm wondering if this is a good overclock setup, but I’m gradually trying to aim higher. Only problem is im running it on air and using the stock heatsink/fan. Any input is appreciated
  10. Problem solved, invested in an Antec TruePower 2.0 550W and it boots up fine now. Thanks for the tip davidhammock200.
  11. Well I just put the OCZ in and its still doing the same thing, ill try the BIOS see how that goes. Update, I tried an older BIOS but it produced the same result. Im wondering if the board needs to be RMA'd at this stage, because I've tried 3 different types of memory brands and it simply wont post with 2x512. But with 1x 512 it posts fine,also on the same topic would cranking the DDR voltage to 3.00 make any change?
×
×
  • Create New...