Jump to content

jm76

Members
  • Content Count

    82
  • Joined

  • Last visited

Everything posted by jm76

  1. Have you looked at the new Mushkin 2x1GB XP4000? http://www.mushkin.com/doc/products/memory_detail.asp?ID=239 Yes, they are more expensive than the OCZ that you linked @ NewEgg but they are guaranteed to run at 500MHz. Jim
  2. LANPARTY UT nF4 SLI-D 704-2BT bios AMD Athlon 64 3000+ Venicer Socket 939 Processor Model ADA3000 DAA4BP – YBBLE 0525DPCW stepping Corsair TWINX2048-3200C2 2x1GB 1x eVGA Geforce 6600GT 128MB 128-bit GDDR3 PCI-Express x16 Video Card 2x Western Digital Caviar SE WD1600JD 160GB 7200 RPM 8MB Cache Serial ATA150 Hard Drive – non-Raid TOSHIBA Black 16X DVD-ROM 52X CD-R 32X CD-RW 52X CD-ROM 2M Cache IDE Combo Drive TOSHIBA Black 16X DVD+R 4X DVD+RW 5X DVD+R DL 12X DVD-R 4X DVD-RW 16X DVD-ROM 48X CD-R 24X CD-RW 48X CD-ROM 2M Cache IDE DVD Burner Antec SmartPower 2.0 SP-500 ATX12V 500W Power Supply ZALMAN CNPS7000B-CU 92mm 2 Ball Cooling Fan/Heatsink ========== Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ration - 3 CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.425v CPU VID Control - 1.425v CPU VID Special Control - Above VID * 104% LDT Voltage Control - 1.40v Chip Set Voltage Control - 1.80v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 150 (DRAM/FSB:3/04) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 8 Read Preamble Time - 6 IdleCycle Limit - 32 Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + A64Tweaker: 3dMark2003: 3dMark2005: Aquamark 3d: Everest Memory Read ========== short description: 270x9 @ 2430Mhz, 1.425v + 104% 2-3-6-3 @ 2.7v vdimm on a 12 divider
  3. Hmm, I can just manage to slide a stick into the orange slot closest to the cpu with the Zantec 7000B on. It's a snug fit but since my ram has a heat spreader on it I'm not worried if it bumps the 7000B during install. Jim
  4. Wired, The link he is talking about is the last line in his sig... The problem with the TechPowerUp link is it doesn't distinguish between the different sizes and definitely doesn't mention lot #'s. For example, it gives that xms3202v2.1 is BH-6; but from what it sounds like, RamGuy needs the size and lot # along with the model number to identify the ICs. Jim
  5. Well I found out that Nanya -5 IC's are used for rev2.1 (assuming that they didn't change the IC's without changing the rev #) haven't been able to find out any usefull information on them though. Does anyone have any information on these IC's. Here is the link where RamGuy states that XMS3202v2.1 are Nanya -5 IC's: http://www.houseofhelp.com/forums/showthread.php?t=42229 Jim
  6. Jaxidian, Are you sure that your Twinx2048 are actually CH6 chips....If you check out the The House of Help (Corsair RAM Forum) it has your module listed as Twinx2048-3200c2 xms3202v1.2 = INFINEON Rev B. You can find a partial list at the Corsair Support Forum: http://www.houseofhelp.com/forums/showthre...0&page=27&pp=15 HTH, Jim
  7. Top right-hand corner of the label there should be something on the order of XMS320#v#.#. The #.# is your revision... If you still don't see it check out this link: http://www.houseofhelp.com/forums/showthread.php?t=34307 I have v2.1 and I'm still trying to figure out what IC's I have. Jim
  8. Out of curiousity have you tried flasing to a newer bios (623-3)? Maybe I was lucky or something but the setup in my sig worked without a hitch when I changed from TWINX1024C2PT to TWINX2048C2... I can't get past Verifying DMI Pool (?) with the ram over 200 MHz but otherwise it's rock solid without errors in Memtest and 8hrs of Prime w/out errors. (Still playing and learning here.) Jim
  9. I've got the same case and it definitely is a nicely built case. You can see my specs in my sig...the only thing with this case is that it's small and you'll find it takes a little more effort to run all the wires. Jim
  10. Hmm, well I decided to take the plunge and I went ahead I purchased an Audigy 2ZS so I'm not terribly concerned with the onboard sound anymore. Jim
  11. lol...the power out is 17 and 19 A (typo on my part) As for the temps...The temps are from MBM5 using the data files posted by someone on this boards and room temp is 27C. The Chipset fan is running at full speed for the most part and is rather loud already. I'm planning on getting an additional fan for my case to blow directly onto the NF4 (is was at 57C while playing CS) and graphics b/c those two are my hot spots. Hopefully with an additional fan I'll be able to close the case up. Guess I'll be flashing 6/23 bios release then. Thanks Jim
  12. The Antec SmartPower 2.0 is a 500W PSU and the output is as follows: Max: [email protected], [email protected], [email protected], [email protected], [email protected], [email protected] This should be suffecient to run this board and the components I have, right? BTW, I've got it booting correctly after retrying the Genie BIOS entries posted in one of the stickies... One thing that concerns me is that the NF4 chipset is running at 55C at idle with the case open and the PWMIC is at 52C idle....Will this cause any problems? As for bios...I haven't updated it yet b/c initially the system booted and ran Windows fine...According to CPU-Z it's 6.00PG date 01/25/2005. When I get the time I'll try flashing it to a more recent one. Thanks for the help, Jim
  13. Never installed NAM/Nvidia Firewall b/c of the issues that I've seen others have... I tried to start the system in diagnositic mode through "msconfig.exe" and it gets to the Windows loading screen and then resets and says the system wasn't shutdown properly.
  14. When I first installed xp64 on Monday it would boot up without a hitch but now the system freezes after it Posts. I can boot into Safe Mode everyonce in a while but I can't boot into SafeMode w/networking. I had this same problem with another system and never could get it resolved so I'm wondering if it's an issue with XP64 or if it's components (all new components on this system). Jim
  15. Just put together a system with: CPU: AMD 64 3000+ Venice MOBO: Lanparty UT nF4 SLI-D RAM: Corsair 2x512 Video: eVGA 6600GT 128MB HDD: WD 160GB SATA Case: Super Lanboy (Antec) PSU: Antec Smartpower 2.0 500W Everything is running fine in XP64 but I don't have any audio off the Karajan Audio Module (I didn't connect the front audio b/c the Super Lanboy's cables aren't long enough to reach the Karajan Audio Module). What slots do the jumpers need to be in on the module for it to work or are there other jumpers that I need to use? I'm planning on getting an audio card but I'd like to get this working as well. Thanks, Jim
×
×
  • Create New...