Jump to content

cwa4me

Members
  • Content Count

    39
  • Joined

  • Last visited

About cwa4me

  • Rank
    New Member
  1. AMD Athlon 64 FX-55 Claw Hammer Socket 939 Processor Model#:ADAFX55DET5AS Stepping:AAA2C0435UPCW DFILanparty NF4 Sli-dr 6/23-3 Bios: http://www.newegg.com/Product/Product.asp?...N82E16813136157 1- Seagate Barracuda 250g sata 7200rpm: http://www.newegg.com/Product/Product.asp?...N82E16822148065 2x512MB OCZ EL Platinum revision 2 memory: http://www.newegg.com/Product/Product.asp?...N82E16820146890 evga 256-p2-n376-AX Geforce 6800GT 256MB 256-bit GDDR3 PCI-Express X16 Vid. card 7.1.2.5 drives-409/1100: http://www.newegg.com/Product/Product.asp?...N82E16814130215 PSU: Antec True Power II 480w sli: http://www.newegg.com/Product/Product.asp?...N82E16817103929 Heatsink: xp-90c,Thermalright: http://www.newegg.com/Product/Product.asp?...N82E16835109122 Heatsink fan: Vantec Tornado 92mm (119 cfm): http://www.newegg.com/Product/Product.asp?...N82E16811999613 * * ========== Genie BIOS Settings: FSB Bus Frequency - 215 LDT/FSB Frequency Ration - x3 CPU/FSB Frequency Ratio - x13 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.325 CPU VID Special Control - Avove VID *114% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level2 Max Async Latency - 07.0 nano seconds Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 3dMark2003: 3dMark2005: Aquamark 3d: Everest Read: ========== short description: 215x13 @ 2797Mhz, 1.325 + 114% 2-2-8-2 @2.8v vdimm
  2. Hey thanks oats, That makes alot of cents,I have a low cfm 120mm for my exhaust,but a high cfm 120mm in my door and another high cfm 120mm in a blow hole. Thanks for clearing it up for me. Now I have a better understanding of how it all works.
  3. I have a xp-90c with a tornado, and if I turn my fan up my temps don't get warmer. If any thing i run cooler, I only turn it down when I'm not doing much and don't want to hear all the noise. With my venice 3200 my idle temps were 25c and a load 38c @2545mhz and my FX-55 idle 35c and load 48c. Thats with my fan wide open Now if I turn it down and prime for a long time my FX-55 my temps are-50-51c. But i guess things are different in different places :confused: lol
  4. Then A.G and r-gone drop another hit of ole timothy, Thinking they will get a better trip with more energy to keep up with the women beating the crap out of the hot dog seller...........
  5. welcome to Dfi-street hope you stay a while and enjoy :nod:
  6. You are so very correct! I am waiting on my 3500 claw hammer to be here next week. But I'm really thinking of picking up a a 3000. Just to have it, because their price is good and it seem like a very good O.Cer. My 3200 is just werd. Lol
  7. I've seen some people go pass 2.5 but I seen alot more where 2.5 was max with this cpu. Mine is acting very crazy. Thats way I got a 3500 Claw Hammer on the way. My 3200 runs prime 95 and stress prime for multiple hours. I've even went as for as priming it for 17 hours and played music at the same time even also went on the internet and surfed and diffirent times while it primed for 17 hours. stable right ? Not, don't get me wrong it does not crash at all, but if I put on a game even drop my vid. card OC to stock and I might play 20 min. are I might play 1 min. this thing will reboot. I even dropped my cpu OC a good amount and it did not help I have to drop it to stock to play games.Now that sucks. I can run sandra,everest,3d01,3d03,3d05,aqua mark,super PI sse2, prime 95, stree prime,and meme test for multiple hours with no problem(prime95 and stress prime and mem test). But I better not put in a game. Now this is confusing. lol
  8. Hey sound thanks for bringing us this great program. Now I can't do with out it. shoot I think i tried out all the extras you offered us.lol but I end up just keeping the regular MBM5 and the screen saver.And since the time you helped me on the phone,and showed more than just to get it working. Like the little features what they are and what they do. I've able to do all kind of neat stuff with my MBM5. Just wanted to say thanks again. And still waiting on Nvidia GPU temps. Lol. I know you have your hands full enough with out having to deal with that. PS: Keep up the good work Bud
  9. The best way to controll your tornado is just buy the vantec nxp-205, It's cheap and works great I have one with 1-92mm tornado and 3-120mm highflow fans and it works great you could use 3 pin or 4 pin molex and it has4 channels and up to 18w per channel. It cost about $25.00 at www.newegg.com. hope this helps. ps. those tornado's are great but freakin loud lol thats why I ask for a good controller and was told about this one and i really enjoy the peace and quiet lol
  10. Protagonist try opening up mbm5 data folder in program files and open up mbmdatafinal file and drag each file from mbmdatafinaand put each one in to the mbm5 data folder one by one and reboot and if you don't see it go in windows start up and click mbm5 and it will all come on . I had the same trouble getting it into the mbm5 data folder but soundx98 had me do it one by one and bam it worked. hope this help's
  11. I'm having the exact same problem and i used a brand new box of floppys still no luck.it makes the same clicking noise and the funny part is it use to work like a charm. i found this out friday. when I tried copying 6/15.any help would be great.
  12. Good luck Mike, I'm having the same problem. wanting more and being stable.my freind has the same cpu and he also max's out at 2.5 just like me. It looks like the 3000venice is the better ocer. There's not many really going over 2.5 with the 3200 venice and being stable.
  13. I use AS5 my temps. 25-26c idle and 36-38c with a load. My freind had the same thing happen to him with ceramic, were he pulled the cpu out of the socket. Just give it a lil twist and it comes right off.
  14. cwa4me

    Got Pets?

    I have a boxer Named Hero (my grandmother named him because she had a boxer and it died so mine carries on the family tradtion lol) He don't do much but sleep and bug my company when they come over.
  15. Happy fathers day to all the great dads out there, Hope ya'll enjoy the day and have a good time with your families :angel:
×
×
  • Create New...