Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by h_Us3r

  1. Bump her up to 300 FSB(for starters)and run the 9x multi, that'll get some of your RAM back at least, mines top's out at 305 x 9 and I coudln't be happier as there IS a noticeable difference in response. I almost have a feeling we have the same stepping/week as this is what I encountered my 1st go around with the OC max on this chip. Hope that helps some, h PS. Peace Kingfisher
  2. I assume that you have an external/2nd PSU for your WC setup, but all the same, unmount the blocks, and disconnect 1 of your vid cards and then try again. Also, is AUTO-DETECT on in the BIOS settings?
  3. Aside from the CMOS clear have you tried re-flashing the BIOS?
  4. I have had this problem before, try 1 drive at a time on a different cable. Although you *might* have hosed your IDE controller if you had a small leak, also check that PSU...your packin some pretty serious gear on a 550w... h
  5. CCBBIE 0610 = she'll go higher. EDIT: You might want to hunt through the OCDB or the x2 4400 thread, Watsonte and Kingfisher have done some amazing stuff with theirs.
  6. I've seen this before, pop back in your old CPU and download/install the AMD dual core drivers then shut down the machine. Clear CMOS for however long with the power cord out of the PSU and the switch off, pop the 4800 back in and boot her up. Note: I would also flash to a more recent BIOS before you do anything. The only reason why I know this is because the same exact thing happened to me and this is what I did minus the BIOS flash as I just did that earlier. Good luck, h
  7. I'll ask the obvious, what is your stepping? What is your target OC, meaning what speed are you trying to hit? She'll definitely do 2.6 that's for sure.
  8. I wish I could run [email protected]:1...I have to run a 5/6 divider, I will try testing a 9/10 once this watercooling situation is resolved. The only thing the HZ guarantees you is that you'll have some more headroom for your OC, nothing more and nothing less. I would also suggest trying to raise your yield by using the 10x multi.
  9. Go with the HZ if you can, and yes, 2.7 on 4400 running the 5/6 seems standard. If she can dual prime for 8+ hrs running the 5/6 at 2.7 I would say leave it there and crack a cold one.
  10. From looking at your screens I would suggest trying these settings: HTT: x3 CPU VID -- 1.45 SPECIAL VID -- above 104% LDT VOLTAGE -- 1.3 DRAM VOLTAGE -- 2.8(for starters, I know that RAM can take more, TCCD?) DRAM DRIVE STRENGTH -- weak 4 DRAM DATA DRIVE STRENGTH -- weak 1 MAL -- 9.0ns RPT -- 7.0ns Try running your RAM at stock settings(3-3-3-8)there is NO WAY your gonna push 1:1 with this CPU trying to run 2.5 - 3 - 2 - 8, although you might get lucky on a 5/6 divider. And even at stock speeds the highest you'll see, also these CPU's seem to prefer the 10x multi.
  11. Max is 2.73 on air running 1.45(VID STARTUP) x 104%(VID SPECIAL)although I am positive she can do 2.8 on water...soon...very soon...
  12. Thanks dude PS, She'll(yours) go higher What are your BIOS settings?
  13. If you guys(or anyone)is familiar with SYSTOOL I have noticed that on initial burn-in the MAX for this CPU is 2.5, this is where it gets weird; looking at some others initial results they claim the highest is 2.5 - 2.6...but this is running at a 1:1 divider. Otherwise, what I am saying is that I *think* they(4400+'s) kind of need to be broken in(constant burn-in sessions?)and at that point you have a VERY small window of time to acheive a "better than average" OC. That's what happened to me, after my first stock burn-in I couldn't even prime 2.6 at a 1/2; now I can prime 2.7 at a 5/6(????)My max is 2.73(no point)All I'm saying is that it's important to keep "reasonably" hammering away on this chip and I promise you that it will bring you a greater yield, how great is anyone's guess. To the 4400+'s(may you burn in prosperously), h
  14. Easy for you to say(cough, 2.9, cough, cough) Ryn, I stand corrected, it's just that the only CCBWE0609DPMW I have seen is the 110w variety, (89w?) Otherwise, I think you *might* be able to hit 2.8. Otherwise, I have a dilemna...do I return this 110w that does [email protected] for an 89w with an unknown stepping that may not OC at all for the chance to possibly get a CCBIE0610 that will do 2.8+ on 1.4VCORE. What do you guys think, any input would be greatly appreciated. THanks sorry for semi-thread jack, h
  15. Where did you get it from? That, is in fact a 110w as far as I know(I have the same stepping...)and 2.7 - 2.73 is the wall.
  16. Awesome, playing with it now. Thanks Corrupt! h
  17. I think you can see 2.8 on her. Have you tried 280 x 10 * 9/10(meaning 280 at the 10 multi using the 9/10 divider)? Anyhow good lucks and congrats! h
  18. I shoulda have knew something was up when it took 1.5 to get 2.6...o well, live and learn.
  19. 2.9.....a beautiful number. What does it feel like?:D Thanks for the blessing, h
  • Create New...