Jump to content

h_Us3r

Members
  • Content count

    339
  • Joined

  • Last visited

About h_Us3r

  • Rank
    Member
  1. h_Us3r

    X2 4400 Wall

    Bump her up to 300 FSB(for starters)and run the 9x multi, that'll get some of your RAM back at least, mines top's out at 305 x 9 and I coudln't be happier as there IS a noticeable difference in response. I almost have a feeling we have the same stepping/week as this is what I encountered my 1st go around with the OC max on this chip. Hope that helps some, h PS. Peace Kingfisher
  2. I assume that you have an external/2nd PSU for your WC setup, but all the same, unmount the blocks, and disconnect 1 of your vid cards and then try again. Also, is AUTO-DETECT on in the BIOS settings?
  3. h_Us3r

    Raid 0

    Kingfishers awesome
  4. Aside from the CMOS clear have you tried re-flashing the BIOS?
  5. It is. (I want a cool SIG template...)
  6. I have had this problem before, try 1 drive at a time on a different cable. Although you *might* have hosed your IDE controller if you had a small leak, also check that PSU...your packin some pretty serious gear on a 550w... h
  7. h_Us3r

    Memtest error after 13 hours

    I am inclined to agree.
  8. h_Us3r

    Figuring out my 4400

    CCBBIE 0610 = she'll go higher. EDIT: You might want to hunt through the OCDB or the x2 4400 thread, Watsonte and Kingfisher have done some amazing stuff with theirs.
  9. h_Us3r

    X2 4800+ Bad CPU???

    I've seen this before, pop back in your old CPU and download/install the AMD dual core drivers then shut down the machine. Clear CMOS for however long with the power cord out of the PSU and the switch off, pop the 4800 back in and boot her up. Note: I would also flash to a more recent BIOS before you do anything. The only reason why I know this is because the same exact thing happened to me and this is what I did minus the BIOS flash as I just did that earlier. Good luck, h
  10. h_Us3r

    Bad 4400+

    I'll ask the obvious, what is your stepping? What is your target OC, meaning what speed are you trying to hit? She'll definitely do 2.6 that's for sure.
  11. I wish I could run [email protected]:1...I have to run a 5/6 divider, I will try testing a 9/10 once this watercooling situation is resolved. The only thing the HZ guarantees you is that you'll have some more headroom for your OC, nothing more and nothing less. I would also suggest trying to raise your yield by using the 10x multi.
  12. Go with the HZ if you can, and yes, 2.7 on 4400 running the 5/6 seems standard. If she can dual prime for 8+ hrs running the 5/6 at 2.7 I would say leave it there and crack a cold one.
  13. h_Us3r

    Bad 4400+

    From looking at your screens I would suggest trying these settings: HTT: x3 CPU VID -- 1.45 SPECIAL VID -- above 104% LDT VOLTAGE -- 1.3 DRAM VOLTAGE -- 2.8(for starters, I know that RAM can take more, TCCD?) DRAM DRIVE STRENGTH -- weak 4 DRAM DATA DRIVE STRENGTH -- weak 1 MAL -- 9.0ns RPT -- 7.0ns Try running your RAM at stock settings(3-3-3-8)there is NO WAY your gonna push 1:1 with this CPU trying to run 2.5 - 3 - 2 - 8, although you might get lucky on a 5/6 divider. And even at stock speeds the highest you'll see, also these CPU's seem to prefer the 10x multi.
  14. Max is 2.73 on air running 1.45(VID STARTUP) x 104%(VID SPECIAL)although I am positive she can do 2.8 on water...soon...very soon...
  15. h_Us3r

    Pass Prime but not Super PI?

    This is a very solid perspective.
×