Jump to content

AAHH&#33&#33kira

Members
  • Content count

    7
  • Joined

  • Last visited

Everything posted by AAHH&#33&#33kira

  1. Do you have settings like 230 3.2v? My 3200 gold don't want to work in dual chanel But in single chanel each stick take 230 2/2/2/7 3.2v without error in one pass of memtest :confused: I've tried with the 310 bios and the 414.3 no way :sad:
  2. Hy, I just have my brand new 2x512 OCZ Pc3200 gold (new bh5) kit... And somthing strange happens... The stock settings 200 2/2/2/5/7 works perfectly @2.8/2.7v But when i wan't to raise 220 2/2/2/6/7 i've errors at test 2 or 3 and 5.... Even @3.2v Memory on slots 2/4 or 1/3 (414.3 bios) the same things happens... The thing that I don't understand that when i test one stick at once both stick do 220 2/2/2/6/7 @2.9v whitout errors on 1 pass of memtest :confused: The stock settings are the settings give by Ryder from OCZ and the oc settings are a mix of settings bring at xtremesytems forums (especially Eva2000 settings...) I which someone have a tips for me the only thing i wan't it's to run cpu @280x9 (I don't go very far with more voltage only 5 or 10+ fsb for 1.67v) with 5/6 mem divider wich do 230mhz 2/2/2/6/7 i tested it also with one stick at once and 3.2v, it works in memtest :sad: Edit: I try with interleave disabled it's not helping i still have some errors And excuse for the bad section
  3. AAHH&#33&#33kira

    Pci-e X800xl Wont Work!!!

    Hello I've had the same problem with my sapphire X800XL. Changing bios to 310 or clear c-mos doesn't help me at all... The only way to got my rig boot were to unplug card, clean contacts and re-plug the card. After that the system will be booting perfectly :tooth: I've rma-ed the graphic and with the new one i've no problem the system boot even cold or hot Now i'm searching why my brand new OCZ 3200 gold bh5 plat won't oc when they are setup in dual chanel and have the same oc capability when i test one at once... :confused: ps: I'm french sorry for the english...
  4. AAHH&#33&#33kira

    What power supply do you have? (open to all platforms)

    Me too :shake: :cool:
  5. I had the same problem with my sapphire"s X800Xl The boot stop at 3 led and sometime the power led light not permanently. If i place the card in the other 16x slot or completly unplugged it the boot goes to the first led and then shut down computer. I must clear off the connector (with my finger on the gold connections) and plug in it firmly, then it boot up... :confused: I'm thinking it was a fabrication default of the graphic card 4 of the connectors are most shiny than the others...
  6. AAHH&#33&#33kira

    NF4 Ultra-D not booting

    It's working now. But i'm not sure it's really the psu fault... :confused: I have put on the enermax but it's happen the same thing 3led lighten and stop at this point. I re-tried to put ram on slot n°2 ,move graphic card,etc.. I finally be a little contraried an i put the graphic card "violently" in place. Now it's working but sometime i need to unscrew the card remove and replace it however it's not booting This happen also if i place the mobo out of the box... I don't know if it was the fault of the x800 or the mobo pciex 16x connector... I'm going back this week-end to the shop where i buy it and make them test it.
  7. Hey everybody! It's my first time on an english speaking forum (i'm french and my english is poor) I just bought an AMD 64 3000+ for upgrading my barton 2500+ configuration. I mount it include all alimentation include the floppy and other molex. When i push the start switch the fans turn on but there si no beep at all and three leds still glowing (i'm not sure of this word light maybe....) I have just mount the memory and the vga and swap all the rest. Then I try with the two ram sticks with all combination nothing work,with one (also tried each stick on each slot) it's not work too . The only way to have some beeps is to unplug the x800 or to put it on the second 16x slot. It's make 1 long beep and 3 short and three led light off but after the beeps the cpu fan comes off and nothingelse appen :confused: I think that' the fault off my scrappy 300w psu but i'm not sur that it isn't the X800 whose failing :eek: Thx in adavnce for the answers
  8. AAHH&#33&#33kira

    NF4 Ultra-D not booting

    What a beautiful song but it's a swiss alps speciality... Yes i swear it's only the psu fault. Normally the new one will be in place monday. The week end will be long... Let's wait for the issue.
×