Jump to content

FutureDFI

Members
  • Content count

    146
  • Joined

  • Last visited

About FutureDFI

  • Rank
    Member
  1. http://www.dfi-street.com/forum/showthread...ght=memory+poll
  2. i ve seen that movie before Hail!!!!!!!! :angel:
  3. FutureDFI

    Hard drive selection:: NF4 NCQ??

    New series T7K250 SATA II seems to be the winner here IMO. http://www.zipzoomfly.com/jsp/ProductDetai...ctCode=100594-2 Unfortunately out of stock for now
  4. I would try mucker's settings but little loose like tcl=2.5 Trcd=4 Tras=8 Trp=4 and Tref = auto (3/10 bios) Also if above dont work I should try a install without RAID arrays to isolate the problem. (sorry i have no idea about RAID).
  5. FutureDFI

    NF4 Random Freezes

    I never had any issue with IDE nVidia drivers but a lot of blue screens with nVidia Network Manager and Firewall. If u have them (and using nVidia ethernet port) try unistall them or use Marvel one for a try.
  6. FutureDFI

    NF4 Ultra-D Bios

    There are some issues with 4V mem Volt jumper look at the extremeforum http://www.xtremesystems.org/forums/showth...ight=dfi+jumper hope it helps
  7. I will agree with most mem settings mucker post I will change tref to Auto give it a try.
  8. Mine works fine. But i m lucky to have an Antec smart power 350W 20pin. Also 10% of forum members use 20 pin. But u have no support from DFI if u use 20pin PSU.
  9. FutureDFI

    DFI NF4 BIOS Memory Guide

    Congratulations!!! It reminds me the old time back at late 80's when we design (and build) small microcomputers for specific jobs in college with Z-80 and 6502 (which remember Spectrum???) Excellent again.
  10. FutureDFI

    Still can't run 3d mark 05

    I u like to use your 20pin PSU (not reccomended by DFI) do it without adapter. As far for the bios. U can see the version when system boot up at bottom left side of the screen. If it says 1/25 u have to flash it to newest bios from DFI 3/10.
  11. I use Corsair XMS 4400 without any issues with 3/10 bios. Also many others (the most) do the same http://www.dfi-street.com/forum/showthread.php?t=10929
  12. If u like to use your PSU, do it but without adapter!!
  13. If u run both sticks in single mode up to 275Mhz i doupt is a RAM problem, but something with mem/genie bios settings. Try the rest and post again. btw what bios u running?
  14. Lets take it from scratch. Use the Orange slots. Vddr = 2.7 - 2.8 more not help at all in my case. Run some memtest on 310 bios with low multiplier-high FSB but keep the Vcore high, let say 1,250-1.300 X 123% = 1.54~1.60V. It doesnt going to hurt your CPU, dont worry. Also track temperatures on ur CPU while runnning Prime (i use speedfan for this). I keep my temps at 55-56 or lower(on load like prime). also at memory settings keep them at 2.5-4-4-8 Auto-Auto ...... but make sure u have tref at Auto and drive strength at L7 data drive strength at L4. Do some memtest and see which is the highest FSB u get without errors on #8 test at least for 10 times pass. (run only #8 test). Keep multiplier at 8 or lower. I had some "odd" situations like i was Prime stable for 2-3 hours and i fail memtest in few minutes :confused: As far the blue screens, may it seems strange, but unistall nVidia network manager - firewall or use the Marvell ethernet port (assume u use them for the internet).
×