Water Cooling Gallery: Show off your work

[Guest ajmatson]

Ya I like Queenz and Mojo's too. Here is a quick of mine on the front page. I am waiting for the UV CCFL's for the case still. It took me two hours to hide all of the wires and cables but I think it turned out pretty well.

 

[RobBan-Swe]

My stripped i7 desktopcase !

And homemade WC.

Borrow WC cooler and pump from my AMD and build a new i7 cpu-block for an hour just for testing WC on i7.

Pumped up the speed from 4400mhz with Air to 4533mhz in CounterS

The i7 is going to get nice design with a smaller waterCooler welded to fit on top of case.

And a special welded peltierwatercooler on side

Some work pics

 

 

 

 

 

 

 

 

[gotdamojo06]

These are awesome :thumbs-up:

 

Favorites so far: queenz + gotdamojo

 

 

EDIT: plus gotdamojo, a duster wouldn't hurt!!!

 

 

That pic is a few months old...I no longer have red dye in there and I did go ahead and dust it not too long ago

 

 

But thanks guys...took about 3 hours to set everything up inside the case...

Edited March 8, 2010 by gotdamojo06

[Geekspeak411]

haha I like the self-weld job xD

[Puck]

Specs in sig.

Ya I like Queenz and Mojo's too. Here is a quick of mine on the front page. I am waiting for the UV CCFL's for the case still. It took me two hours to hide all of the wires and cables but I think it turned out pretty well.

 

You'll both probably get better temps going res->pump->cpu->rad instead of pump->rad->cpu->res

[ccokeman]

My stripped i7 desktopcase !

And homemade WC.

Borrow WC cooler and pump from my AMD and build a new i7 cpu-block for an hour just for testing WC on i7.

Pumped up the speed from 4400mhz with Air to 4533mhz in CounterS

The i7 is going to get nice design with a smaller waterCooler welded to fit on top of case.

And a special welded peltierwatercooler on side

Some work pics

 

 

 

 

 

 

 

Nice to see that kind of work!

[ccokeman]

Ya I like Queenz and Mojo's too. Here is a quick of mine on the front page. I am waiting for the UV CCFL's for the case still. It took me two hours to hide all of the wires and cables but I think it turned out pretty well.

 

 

I think you need to fix the res! Its like the leaning tower and gives a noobish look to the Implementation! Other than that Quite nice!

[rud3bwoy]

 

 

 

i7 920 D0 4ghz|Corsair 1000 watts psu|Asus Rampage 2 extreme|Corsair 1800 Mhz Dominator 6GB|GTX 295|OCZ VERTEX 250GB SSD/Wd 500 Gb storage|Xfi Platinum sound card|Dell 24 inch Ultra Sharp|Logitech Z5500|Water Cooled|ABS Canyon 695 Case|

 

should be adding another vertex 250 gb drive for raid 0 soon along with the new intel 6 core processors and new gtx series

 

 

3.0 ghz i had it at 4.0 ghz but seen no real difference at all in anything i did so was a useless oc

 

idle low 30s and 50 on prime for a few hours.

Edited March 8, 2010 by rud3bwoy

[Guest ajmatson]

You'll both probably get better temps going res->pump->cpu->rad instead of pump->rad->cpu->res

I have the setup that way in my other rig and the temp difference is negligible, 1C degree at best.

 

 

I think you need to fix the res! Its like the leaning tower and gives a noobish look to the Implementation! Other than that Quite nice!

I had it up however, the tubing I am using has the 5/8" wall and the bends were too much to the pump that it was causing kinking and because of the PSU I cannot lower the res anymore Best I could get it.