mknwatt Posted May 3, 2008 Posted May 3, 2008 DFI LP UT P35 T2R, 2/14 BIOS OCZ DDR2 PC2-8800 Gold Dual Channel 2GB (2 x 1GB) OCZ2G11002GK Intel Core 2 Duo E8500 Wolfdale 3.16GHz 6M L2 Cashe ( Q807A217 ), Swifttech Storm Rev.2 BFG 8800GTX 768MB 384-bit GDDR3 PCI-E x16 @ 661/1116 ~ NVIDIA 169.21 drivers, DD NV-88GTX 2x Western Digital Caviar SE WD1600JS 160GB 7200 RPM 8MB Cache SATA 3.0Gb/s, RAID-0 SONY DVD RW DRU-700A PC Power & Cooling Silencer 750 Quad (Black) DD-D5 pump - Stealth GTS 360 Rad. ==================== [b]CPU Feature Page[/b][color=red] Thermal Management Control................Enabled PPM (EIST) Mode...........................Enabled Limit CPUID MaxVal........................Disabled CIE Function..............................Auto Execute Disable Bit.......................Enabled Virtualization Technology.................Enabled Core Multi-Processing.....................Enabled[/color] [b]Main BIOS Page[/b][color=red] Exist Setup Shutdown......................Mode 2 Shutdown After AC Loss....................Disabled O. C. Fail Retry Counter..................0 CLOCK VC0 Divider.........................Auto CPU Clock Ratio...........................9x CPU N/2 Ratio.............................Disabled [i] -Target CPU Clock.......................4203 MHz[/i] CPU Clock.................................467 MHz Boot Up Clock.............................Auto DRAM Speed................................333/800 [i] -Target DRAM Speed......................DDR2 1121[/i] PCIE Clock................................100MHz PCIE Slot Config..........................1X 1X CPU Spread Spectrum.......................Disabled PCIE Spread Spectrum......................Disabled SATA Spread Spectrum......................Disabled[/color] [b]Voltage Setting Page [/b][color=red] CPU VID Control...........................Auto CPU VID Special Add.......................110.62% DRAM Voltage Control......................2.23V SB 1.05V Voltage..........................1.070V SB Core/CPU PLL Voltage...................1.55V NB Core Voltage...........................1.45V CPU VTT Voltage...........................1.10V VCore Droop Control.......................Disabled Clockgen Voltage Control..................3.45V GTL+ Buffers Strength.....................Strong Host Slew Rate............................Weak GTL REF Voltage Control...................Enabled CPU GTL 1/3 REF Volt......................50 CPU GTL 0/2 REF Volt......................50 North Bridge GTL REF Volt ................66[/color] [b]DRAM Timing Page[/b][color=red] Enhance Data Transmitting.................Fast Enhance Addressing........................Fast T2 Dispatch...............................Auto Clock Setting Fine Delay..................Listed Below CAS Latency Time (tCL)....................5 RAS# to CAS# Delay (tRCD).................5 RAS# Precharge (tRP)......................5 Precharge Delay (tRAS)....................15 All Precharge to Act......................5 REF to ACT Delay (tRFC)...................42 Performance LVL (Read delay)..............7 Read delay phase adjust...................Listed Below MCH ODT Latency...........................2 Write to PRE Delay (tWR)..................12 Rank Write to Read (tWTR).................10 ACT to ACT Delay (tRRD)...................3 Read to Write Delay (tRDWR)...............8 Ranks Write to Write (tWRWR)..............4 Ranks Read to Read (tRDRD)................5 Ranks Write to Read (tWRRD)...............4 Read CAS# Precharge (tRTP)................2 ALL PRE to Refresh........................5[/color] [b]Clock Setting Fine Delay Page[/b][color=red] Ch1 Clock Crossing Setting................More Aggressive DIMM 1 Clock fine delay...................Current 156ps DIMM 2 Clock fine delay...................Current 556ps Ch 1 Command fine delay...................Current 868ps CH 1 Control fine delay...................Current 623ps Ch2 Clock Crossing Setting................More Aggressive DIMM 3 Clock fine delay...................Current 156ps DIMM 4 Clock fine delay...................Current 623ps Ch 2 Command fine delay...................Current 868ps CH 2 Control fine delay...................Current 556ps Ch1Ch2 CommonClock Setting................More Aggressive Ch1 RDCAS GNT-Chip Delay..................Auto Ch1 WRCAS GNT-Chip Delay..................Auto Ch1 Command to CS Delay...................Auto Ch2 RDCAS GNT-Chip Delay..................Auto Ch2 WRCAS GNT-Chip Delay..................Auto Ch2 Command to CS Delay...................Auto[/color] [b]Read Delay Phase Adjust Page[/b][color=red] [i]Ch1 Read delay phase(4~0) 6- 7- 7- 7- 6[/i] Channel 1 Phase 0 Pull-In.................Auto Channel 1 Phase 1 Pull-In.................Auto Channel 1 Phase 2 Pull-In.................Auto Channel 1 Phase 3 Pull-In.................Auto Channel 1 Phase 4 Pull-In.................Auto [i]Ch2 Read delay phase(4~0) 7- 7- 7- 7- 6[/i] Channel 2 Phase 0 Pull-In.................Auto Channel 2 Phase 1 Pull-In.................Auto Channel 2 Phase 2 Pull-In.................Auto Channel 2 Phase 3 Pull-In.................Auto Channel 2 Phase 4 Pull-In.................Auto[/color] ==================== Prime 95, CPU-Z, 3Dmark2001SE, GPU-Z, MemSet: 3Dmark03, SuperPi 1M, CPU-Z, GPU-Z, MemSet: 3Dmark05, SuperPi 32M, CPU-Z, GPU-Z, MemSet: 3Dmark06, Everest, CPU-Z, GPU-Z, MemSet: ==================== shot description: 467 x 9 @ 4.2 GHz ~ Auto * 110.62 (1.34) Vcore 2Gig DDR2 1121 MHz (5-5-5-15-2T) Share this post Link to post Share on other sites More sharing options...
Guest LithoTech Posted May 4, 2008 Posted May 4, 2008 DFI LP DK P35-T2RS (01/09/2008 Beta BIOS) Intel P4-640 Prescott 3.2GHz/800/2MB @ 4.0GHz (SL8Q7 8632B930 Jan 11/07) 2x1024 G.Skill 6400 NQ (F2-6400CL5D-2GBNQ) eVGA 6800GS @ 425/1000, 91.47 Drivers Seagate Barracuda 7200.10 250GB 16MB Sata2 Pioneer DVR-212D DVD R/W OCZ StealthXStream 600W HSPC Tech Station (Top Deck) Arctic Cooling Freezer 7 Pro ========== [b]Genie BIOS Setting:[/b] [color=red]Exit Setup shutdown....................... - Mode 2 CLOCK VCO divider......................... - Auto CPU Clock Ratio........................... - N/A - Target CPU Clock........................ - 4000 MHz CPU Clock................................. - 250 MHz Boot Up Clock............................. - Auto DRAM Speed................................ - 333/800 - Target DRAM Speed....................... - DDR2 1000 PCIE Clock................................ - 100 MHz CPU Spread Spectrum....................... - Disabled PCIE Spread Spectrum...................... - Disabled SATA Spread Spectrum...................... - Disabled[/color] [b]CPU Feature:[/b] [color=red]Thermal Management Control................ - Disabled PPM(EIST) Mode............................ - Disabled Limit CPUID MaxVal........................ - Disabled C1E Function.............................. - Disabled Execute Disable Bit....................... - Enabled Core Multi-Processing..................... - N/A[/color] [b]Voltage Setting:[/b] [color=red]CPU VID Control........................... - N/A CPU VID Special Add....................... - +37.5mV (1.37 Bios 1.39 OS) DRAM Voltage Control...................... - 1.9V SB 1.05V Voltage.......................... - 1.070V SB Core/CPU PLL Voltage................... - 1.55V NB Core Voltage........................... - 1.35V CPU VTT Voltage........................... - 1.2V Clockgen Voltage Control.................. - 3.45V CPU GTL 1/3 REF Volt..................... - 67 CPU GTL 0/2 REF Volt..................... - 67 North Bridge GTL REF Volt................. - 67[/color] [b]DRAM Timing:[/b] [color=red]Enhance Data transmitting................. - Fast Enhance Addressing........................ - Fast T2 Dispatch............................... - Disabled CAS Latency Time (tCL).................... - 5 RAS# to CAS# Delay (tRCD)................. - 5 RAS# Precharge (tRP)...................... - 5 Precharge delay (tRAS).................... - 15 All Precharge to ACT...................... - Auto 5 REF to ACT Delay (tRFC)................... - Auto 42 Preformance LVL (Read delay).............. - Auto 3 MCH ODT Latencey.......................... - Auto Write to PRE Delay (tWR).................. - Auto 14 Rank Write to Read (tWTR)................. - Auto 11 ACT to ACT Delay (tRRD)................... - Auto 3 Read to Write Delay (tRDWR)............... - Auto 8 Ranks Write to Write (tWRWR).............. - Auto Ranks Read to Read (tRDRD)................ - Auto Ranks Write to Read (tWRRD)............... - Auto Read CAS# Precharge (tRTP)................ - Auto 3 All PRE to Refresh........................ - Auto 5[/color] [b]Clock Setting Fine Delay:[/b] [color=red]Ch1 Clock Crossing Setting................ - More Aggressive DIMM 1 Clock fine delay................... - Current 44ps DIMM 2 Clock fine delay................... - Current 445ps Ch1 Command fine delay.................... - Current 756ps Ch1 Control fine delay.................... - Current 512ps Ch2 Clock Crossing Setting................ - More Aggressive DIMM 3 Clock fine delay................... - Current 44ps DIMM 4 Clock fine delay................... - Current 512ps Ch2 Command fine delay.................... - Current 756ps Ch2 Control fine delay.................... - Current 445ps Ch1Ch2 CommonClock Setting................ - More Aggressive Ch1 RDCAS GNT-Chip Delay.................. - Auto Ch1 WRCAS GNT-Chip Delay.................. - Auto Ch1 Command to CS Delay................... - Auto Ch2 RDCAS GNT-Chip Delay.................. - Auto Ch2 WRCAS GNT-Chip Delay.................. - Auto Ch2 Command to CS Delay................... - Auto[/color] [b]Read delay phase adjust:[/b] [color=red][I]Ch1 Read delay phase(4~0) 3-3-3-3-3[/I] Channel 1 Phase 0 Pull-In................. - Auto Channel 1 Phase 1 Pull-In................. - Auto Channel 1 Phase 2 Pull-In................. - Auto Channel 1 Phase 3 Pull-In................. - Auto Channel 1 Phase 4 Pull-In................. - Auto [I]Ch2 Read delay phase(4~0) 3-3-3-3-3[/I] Channel 2 Phase 0 Pull-In................. - Auto Channel 2 Phase 1 Pull-In................. - Auto Channel 2 Phase 2 Pull-In................. - Auto Channel 2 Phase 3 Pull-In................. - Auto Channel 2 Phase 4 Pull-In................. - Auto[/color] ========== Prime95, CPUZ, 3Dmark2001SE, MemSet: 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark: ========== Short Description: 250x16 @ 4.0GHz 1.37vcore (BIOS) 1.39V (O/S) 5-5-5-15 1000MHz 1.90vdimm . Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted June 28, 2008 Posted June 28, 2008 DFI LP UT P35-T2R (03/17/2008 BIOS) Intel E8500 (Q746A579) 2x1024 OCZ PC9600 FLEX (OCZ2FX12001G) 8800 Ultra @ 710/1140, 169.21 Drivers 2X36GB Raptor RAID 0 / 250GB Caviar Pioneer DVR 111D Pcp&P Turbocool 1Kw Mach2 GT/Chilly1/Desuperheater ========== [b]Genie BIOS Settings:[/b] [color=red] Genie BIOS Setting: Exit Setup shutdown....................... - Mode 2 CLOCK VCO divider......................... - Auto CPU Clock Ratio........................... - 9.5 X CPU-N2 Ratio.............................. - Disabled - Target CPU Clock........................ - 4750 MHz CPU Clock................................. - 500 MHz Boot Up Clock............................. - Auto DRAM Speed................................ - 333/800 - Target DRAM Speed....................... - DDR2 1201 PCIE Clock................................ - 100 MHz PCIE Slot Config.......................... - 1X 1X CPU Spread Spectrum....................... - Disabled PCIE Spread Spectrum...................... - Disabled SATA Spread Spectrum...................... - Disabled CPU Feature: Thermal Management Control................ - Enabled PPM(EIST) Mode............................ - Enabled Limit CPUID MaxVal........................ - Disabled C1E Function.............................. - Auto Execute Disable Bit....................... - Enabled Virtualization Technology................. - Disabled Core Multi-Processing..................... - Enabled Voltage Setting: CPU VID Control........................... - Auto CPU VID Special Add....................... - 126.45% DRAM Voltage Control...................... - 2.27V SB 1.05V Voltage.......................... - 1.15V SB Core/CPU PLL Voltage................... - 1.55V NB Core Voltage........................... - 1.53V CPU VTT Voltage........................... - 1.17V Vcore Droop Control....................... - Enabled Clockgen Voltage Control.................. - 3.45V GTL+ Buffers Strenght..................... - Strong Host Slew Rate............................ - Strong GTL REF Voltage Control................... - Enabled CPU GTL 1/3 REF Volt..................... - 68 CPU GTL 0/2 REF Volt..................... - 67 North Bridge GTL REF Volt................. - 69 DRAM Timing: Enhance Data transmitting................. - Fast Enhance Addressing........................ - Fast T2 Dispatch............................... - Auto CAS Latency Time (tCL).................... - 5 RAS# to CAS# Delay (tRCD)................. - 5 RAS# Precharge (tRP)...................... - 5 Precharge delay (tRAS).................... - 15 All Precharge to ACT...................... - 5 REF to ACT Delay (tRFC)................... - 33 Preformance LVL (Read delay).............. - 8 MCH ODT Latencey.......................... - AUTO Write to PRE Delay (tWR).................. - 13 Rank Write to Read (tWTR)................. - 11 ACT to ACT Delay (tRRD)................... - 3 Read to Write Delay (tRDWR)............... - 8 Ranks Write to Write (tWRWR).............. - AUTO Ranks Read to Read (tRDRD)................ - AUTO Ranks Write to Read (tWRRD)............... - AUTO Read CAS# Precharge (tRTP)................ - 3 All PRE to Refresh........................ - 5 Clock Setting Fine Delay: Ch1 Clock Crossing Setting................ - More Aggressive DIMM 1 Clock fine delay................... - Current[44] DIMM 2 Clock fine delay................... - Current[445] Ch1 Command fine delay.................... - Current[756] Ch1 Control fine delay.................... - Current[512] Ch2 Clock Crossing Setting................ - More Aggressive DIMM 3 Clock fine delay................... - Current[44] DIMM 4 Clock fine delay................... - Current[512] Ch2 Command fine delay.................... - Current[756] Ch2 Control fine delay.................... - Current[445] Ch1Ch2 CommonClock Setting................ - More Aggressive Ch1 RDCAS GNT-Chip Delay.................. - Auto Ch1 WRCAS GNT-Chip Delay.................. - Auto Ch1 Command to CS Delay................... - Auto Ch2 RDCAS GNT-Chip Delay.................. - Auto Ch2 WRCAS GNT-Chip Delay.................. - Auto Ch2 Command to CS Delay................... - Auto Read delay phase adjust: Channel 1 Phase 0 Pull-In................. - Enabled Channel 1 Phase 1 Pull-In................. - Enabled Channel 1 Phase 2 Pull-In................. - Enabled Channel 1 Phase 3 Pull-In................. - Enabled Channel 1 Phase 4 Pull-In................. - Enabled Channel 2 Phase 0 Pull-In................. - Enabled Channel 2 Phase 1 Pull-In................. - Enabled Channel 2 Phase 2 Pull-In................. - Enabled Channel 2 Phase 3 Pull-In................. - Enabled Channel 2 Phase 4 Pull-In................. - Enabled [/color] ========== Orthos: 3dMark2001: 3dMark2003: 3dMark 2005: 3dMark 06: Aquamark: ========== short description: 500x9.5 @ 4750Mhz, Mach2 GT cooling Share this post Link to post Share on other sites More sharing options...
r3d c0m3t Posted June 29, 2008 Posted June 29, 2008 And the dislike continues. Awesome results, I've come to expect nothing but 4.xx from you. Share this post Link to post Share on other sites More sharing options...
hardnrg Posted July 9, 2008 Posted July 9, 2008 EVGA 680i A1 (P32 BIOS) Intel Q6600 (SLACR/G0, 1.325V VID) 2x1024 OCZ PC9200 FLEX (OCZ2FX11502GK) 2x 8800 GTS (SLI) @ 702/1674/1053, 177.35 Drivers 4x Hitachi T7K500 250GB SATA2 (Highpoint RAID-10) 2x Hitachi T7K500 250GB SATA2 (nVidia RAID-0) 2x Samsung T166 500GB SATA2 2x Hitachi T7K250 250GB SATA2 Seagate Freeagent 250GB USB2 NEC ND3500AG DVDRW PCP&C Silencer 750 Water: Loop1: Laing D5 Vario (Pump) -> Swiftech MCR220 (Rad) -> DTek Fuzion (CPU block) -> DD 680i Maze4 (NB block) -> ((Pump)) Loop2: Swiftech MCP655 (Pump) -> EK 680i MOSFET Type1 -> EK 680i MOSFET Type2 -> Thermochill PA120.3 (Rad) -> (split: OCZ FlexXLC (RAMblock) -> OCZ FlexXLC (RAMblock)) -> DD NV88GTS (GPU full block) -> DD NV88GTS (GPU full block) -> (Pump) ========== Advanced Chipset Features: System Clocks: CPU Multi................................. - 8x PCIEx16_1, MHz............................ - 100 PCIEx16_3, MHz............................ - 100 PCIEx16_2, MHz............................ - 100 SPP<->MCP, MHz............................ - 200 SPP<->MCP, MHz............................ - 200 SPP->MCP.................................. - 5x SPP<-MCP.................................. - 5x PCIE Spread Spectrum...................... - Disabled FSB & Memory Configuration: FSB - Memory Clock Mode.................. - Linked FSB - Memory Ratio....................... - Sync Mode FSB (QDR), MHz........................... - 1800 Memory Timing Setting: Memory Timing Setting.................. - Expert tCL.................................... - 4 tRCD................................... - 3 tRP.................................... - 3 tRAS................................... - 10 CMD.................................... - 2T tRRD................................... - 3 tRC.................................... - 16 tWR.................................... - 5 tWTR................................... - 9 tREF................................... - 7.8us CPU Configuration: Limit CPU ID MaxVal...................... - Disabled Intel Speedstep.......................... - Disabled PPM Mode............................... - Native Mode CPU Thermal Control...................... - Disabled C1E Enhanced Halt State.................. - Disabled Execute Disable Bit...................... - Enabled Virtualisation Technology................ - Enabled System Voltages: CPU Core................................. - 1.56875 CPU FSB.................................. - 1.5 Memory................................... - 2.100 SPP...................................... - 1.50 MCP...................................... - 1.600 SPP<->MCP................................ - 1.25 System BIOS Cacheable...................... - Disabled HPET Function.............................. - Enabled NVidia GPU Ex.............................. - Enabled ========== Everest: Prime95 v25: 24 hours 3dMark2001: 69,562 3dMark2003: 67,763 3dMark 2005: 24,092 3dMark 06: 18,813 Aquamark: 197,309 ========== short description: 8x450 = 3600Mhz, 1.56875V, DTek Fuzion 450MHz, 4-3-3-10-2T, 2.1V, Flex(water) Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted September 6, 2008 Posted September 6, 2008 (edited) DFI LP UT P35-T2R (05/02/2008 BIOS) Intel E8600 (Q822A435) 2x1024 OCZ PC9600 FLEX (OCZ2FX12001G) 8800 Ultra @ 710/1140, 169.21 Drivers 2X36GB Raptor RAID 0 / 250GB Caviar Pioneer DVR 111D Pcp&P Turbocool 1Kw Mach2 GT/Chilly1/Desuperheater ========== [b]Genie BIOS Settings:[/b] [color=red] Genie BIOS Setting: Exit Setup shutdown....................... - Mode 2 CLOCK VCO divider......................... - Auto CPU Clock Ratio........................... - 10.0 X CPU-N2 Ratio.............................. - Disabled - Target CPU Clock........................ - 5100 MHz CPU Clock................................. - 510 MHz Boot Up Clock............................. - Auto DRAM Speed................................ - 333/800 - Target DRAM Speed....................... - DDR2 1224 PCIE Clock................................ - 100 MHz PCIE Slot Config.......................... - 1X 1X CPU Spread Spectrum....................... - Disabled PCIE Spread Spectrum...................... - Disabled SATA Spread Spectrum...................... - Disabled CPU Feature: Thermal Management Control................ - Enabled PPM(EIST) Mode............................ - Enabled Limit CPUID MaxVal........................ - Disabled C1E Function.............................. - Auto Execute Disable Bit....................... - Enabled Virtualization Technology................. - Enabled Core Multi-Processing..................... - Enabled Voltage Setting: CPU VID Control........................... - Auto CPU VID Special Add....................... - 124.56% DRAM Voltage Control...................... - 2.27V SB 1.05V Voltage.......................... - 1.15V SB Core/CPU PLL Voltage................... - 1.55V NB Core Voltage........................... - 1.53V CPU VTT Voltage........................... - 1.15V Vcore Droop Control....................... - Enabled Clockgen Voltage Control.................. - 3.45V GTL+ Buffers Strenght..................... - Strong Host Slew Rate............................ - Strong GTL REF Voltage Control................... - Enabled CPU GTL 1/3 REF Volt..................... - 68 CPU GTL 0/2 REF Volt..................... - 67 North Bridge GTL REF Volt................. - 67 DRAM Timing: Enhance Data transmitting................. - Fast Enhance Addressing........................ - Fast T2 Dispatch............................... - Auto CAS Latency Time (tCL).................... - 5 RAS# to CAS# Delay (tRCD)................. - 5 RAS# Precharge (tRP)...................... - 5 Precharge delay (tRAS).................... - 15 All Precharge to ACT...................... - 5 REF to ACT Delay (tRFC)................... - 33 Preformance LVL (Read delay).............. - 8 MCH ODT Latencey.......................... - AUTO Write to PRE Delay (tWR).................. - 13 Rank Write to Read (tWTR)................. - 11 ACT to ACT Delay (tRRD)................... - 3 Read to Write Delay (tRDWR)............... - 8 Ranks Write to Write (tWRWR).............. - AUTO Ranks Read to Read (tRDRD)................ - AUTO Ranks Write to Read (tWRRD)............... - AUTO Read CAS# Precharge (tRTP)................ - 3 All PRE to Refresh........................ - 5 Clock Setting Fine Delay: Ch1 Clock Crossing Setting................ - More Aggressive DIMM 1 Clock fine delay................... - Current[89] DIMM 2 Clock fine delay................... - Current[489] Ch1 Command fine delay.................... - Current[801] Ch1 Control fine delay.................... - Current[545] Ch2 Clock Crossing Setting................ - More Aggressive DIMM 3 Clock fine delay................... - Current[89] DIMM 4 Clock fine delay................... - Current[545] Ch2 Command fine delay.................... - Current[801] Ch2 Control fine delay.................... - Current[489] Ch1Ch2 CommonClock Setting................ - More Aggressive Ch1 RDCAS GNT-Chip Delay.................. - Auto Ch1 WRCAS GNT-Chip Delay.................. - Auto Ch1 Command to CS Delay................... - Auto Ch2 RDCAS GNT-Chip Delay.................. - Auto Ch2 WRCAS GNT-Chip Delay.................. - Auto Ch2 Command to CS Delay................... - Auto Read delay phase adjust: Channel 1 Phase 0 Pull-In................. - Enabled Channel 1 Phase 1 Pull-In................. - Enabled Channel 1 Phase 2 Pull-In................. - Enabled Channel 1 Phase 3 Pull-In................. - Enabled Channel 1 Phase 4 Pull-In................. - Enabled Channel 2 Phase 0 Pull-In................. - Enabled Channel 2 Phase 1 Pull-In................. - Enabled Channel 2 Phase 2 Pull-In................. - Enabled Channel 2 Phase 3 Pull-In................. - Enabled Channel 2 Phase 4 Pull-In................. - Enabled [/color] ========== Orthos/3d01 3dMark2003: 3dMark 2005: 3dMark 06: ========== short description: 510x10 @ 5100Mhz, Mach2 GT cooling Edited December 18, 2008 by kitfit1 Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted September 28, 2008 Posted September 28, 2008 DFI LP UT P35-T2R (05/02/2008 BIOS) Intel E8600 (Q822A435) 2x1024 OCZ PC9600 FLEX (OCZ2FX12001G) ATI 4870x2 @ 850/950, Cat 8.9 2X36GB Raptor RAID 0 / 250GB Caviar Pioneer DVR 111D Pcp&P Turbocool 1Kw Mach2 GT/Chilly1/Desuperheater ========== [b]Genie BIOS Settings:[/b] [color=red] Genie BIOS Setting: Exit Setup shutdown....................... - Mode 2 CLOCK VCO divider......................... - Auto CPU Clock Ratio........................... - 10.0 X CPU-N2 Ratio.............................. - Disabled - Target CPU Clock........................ - 5100 MHz CPU Clock................................. - 510 MHz Boot Up Clock............................. - Auto DRAM Speed................................ - 333/800 - Target DRAM Speed....................... - DDR2 1224 PCIE Clock................................ - 100 MHz PCIE Slot Config.......................... - 1X 1X CPU Spread Spectrum....................... - Disabled PCIE Spread Spectrum...................... - Disabled SATA Spread Spectrum...................... - Disabled CPU Feature: Thermal Management Control................ - Enabled PPM(EIST) Mode............................ - Enabled Limit CPUID MaxVal........................ - Disabled C1E Function.............................. - Auto Execute Disable Bit....................... - Enabled Virtualization Technology................. - DISABLED Core Multi-Processing..................... - Enabled Voltage Setting: CPU VID Control........................... - Auto CPU VID Special Add....................... - 124.56% DRAM Voltage Control...................... - 2.27V SB 1.05V Voltage.......................... - 1.15V SB Core/CPU PLL Voltage................... - 1.55V NB Core Voltage........................... - 1.53V CPU VTT Voltage........................... - 1.15V Vcore Droop Control....................... - Enabled Clockgen Voltage Control.................. - 3.45V GTL+ Buffers Strenght..................... - Strong Host Slew Rate............................ - Strong GTL REF Voltage Control................... - Enabled CPU GTL 1/3 REF Volt..................... - 68 CPU GTL 0/2 REF Volt..................... - 67 North Bridge GTL REF Volt................. - 67 DRAM Timing: Enhance Data transmitting................. - Fast Enhance Addressing........................ - Fast T2 Dispatch............................... - Auto CAS Latency Time (tCL).................... - 5 RAS# to CAS# Delay (tRCD)................. - 5 RAS# Precharge (tRP)...................... - 5 Precharge delay (tRAS).................... - 15 All Precharge to ACT...................... - 5 REF to ACT Delay (tRFC)................... - 33 Preformance LVL (Read delay).............. - 8 MCH ODT Latencey.......................... - AUTO Write to PRE Delay (tWR).................. - 13 Rank Write to Read (tWTR)................. - 11 ACT to ACT Delay (tRRD)................... - 3 Read to Write Delay (tRDWR)............... - 8 Ranks Write to Write (tWRWR).............. - AUTO Ranks Read to Read (tRDRD)................ - AUTO Ranks Write to Read (tWRRD)............... - AUTO Read CAS# Precharge (tRTP)................ - 3 All PRE to Refresh........................ - 5 Clock Setting Fine Delay: Ch1 Clock Crossing Setting................ - More Aggressive DIMM 1 Clock fine delay................... - Current[89] DIMM 2 Clock fine delay................... - Current[489] Ch1 Command fine delay.................... - Current[801] Ch1 Control fine delay.................... - Current[545] Ch2 Clock Crossing Setting................ - More Aggressive DIMM 3 Clock fine delay................... - Current[89] DIMM 4 Clock fine delay................... - Current[545] Ch2 Command fine delay.................... - Current[801] Ch2 Control fine delay.................... - Current[489] Ch1Ch2 CommonClock Setting................ - More Aggressive Ch1 RDCAS GNT-Chip Delay.................. - Auto Ch1 WRCAS GNT-Chip Delay.................. - Auto Ch1 Command to CS Delay................... - Auto Ch2 RDCAS GNT-Chip Delay.................. - Auto Ch2 WRCAS GNT-Chip Delay.................. - Auto Ch2 Command to CS Delay................... - Auto Read delay phase adjust: Channel 1 Phase 0 Pull-In................. - Enabled Channel 1 Phase 1 Pull-In................. - Enabled Channel 1 Phase 2 Pull-In................. - Enabled Channel 1 Phase 3 Pull-In................. - Enabled Channel 1 Phase 4 Pull-In................. - Enabled Channel 2 Phase 0 Pull-In................. - Enabled Channel 2 Phase 1 Pull-In................. - Enabled Channel 2 Phase 2 Pull-In................. - Enabled Channel 2 Phase 3 Pull-In................. - Enabled Channel 2 Phase 4 Pull-In................. - Enabled [/color] ========== Orthos/3d01: 3dMark2003: 3dMark 2005: 3dMark 06: ========== short description: 510x10 @ 5100Mhz, Mach2 GT cooling Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted December 27, 2008 Posted December 27, 2008 DFI LP UT P45-T2RS (12/12/2008 BIOS) Intel E8600 (Q826A457) 4x1024 OCZ PC9600 FLEX (OCZ2FX12001G) ATI 4870x2, Cat 8.12 2X36GB Raptor RAID 0 / 250GB Caviar Pioneer DVR 111D Pcp&P Turbocool 1Kw Mach2 GT/Chilly1/Desuperheater Vista Ultimate 64 [b]Genie BIOS Settings:[/b] [color=red] Exit Setup shutdown........................... - Mode 2 Shutdown after AC loss........................ - Enabled AC Shutdown free.............................. - Enabled O.C. Fail retry Counter....................... - 1 O.C. Fail CMOS Reload......................... - Disabled CPU Clock Ratio............................... - 8.5x CPU N/2 Ratio................................. - Enabled Target CPU Clock.............................. - 4791 MHz CPU Clock..................................... - 563 MHz Boot Up Clock................................. - Auto CPU Clock Amplitude........................... - 800mV CPU Clock0 Skew............................... - 100ps CPU Clock1 Skew............................... - 0ps DRAM Speed.................................... - 400/800 Target DRAM Speed............................. - DDR2 1126 PCIE Clock.................................... - 100 MHz CPU Spread Spectrum........................... - Disabled PCIE Spread Spectrum.......................... - Disabled CPU Feature Thermal Management Control.................... - Enabled PPM (EIST)Mode................................ - Disabled Limit CPUID MaxVal............................ - Disabled C1E Function.................................. - Enabled Execute Disable Bit........................... - Enabled Virtualization Technology..................... - Enabled Core Multi-Processing......................... - Enabled DRAM Timing Enhance Data Transmitting..................... - Fast Enhanced Addressing........................... - Fast T2 Dispatch................................... - Auto Flex Memory Mode.............................. - Auto CAS Latency Time (tCL)........................ - 5 RAS# to CAS# Delay (tRCD)..................... - 5 RAS# Precharge (tRP).......................... - 5 Precharge Delay (tRAS)........................ - 15 All Precharge to ACT.......................... - Auto REF to ACT Delay (tRFC)....................... - 43 Performance LVL (Read Delay).................. - Auto Write to PRE Delay (tWR)...................... - Auto Rank Write to Read (tWTR)..................... - Auto ACT to ACT Delay (tRRD)....................... - Auto Read to Write Delay (tRDWR)................... - Auto Ranks Write to Write (tWRWR).................. - Auto Ranks Write to Read (tWRRD)................... - Auto Read CAS# Precharge (tRTP).................... - Auto All PRE to Refresh............................ - Auto Clock Setting Fine Delay DLL and RCOMP Settings........................ - By Menu CH1 DRAM Default Skew......................... - Model 3 CH2 DRAM Default Skew......................... - Model 3 RCOMP Setting................................. - Model 1 Fine Delay Step Degree........................ - 70ps Ch1 Clock Crossing Setting.................... - Auto DIMM 1 Clock fine delay....................... - current 1924ps DIMM 2 Clock fine delay....................... - current 1924ps Ch1 Control0 fine delay....................... - current 194ps Ch1 Control1 fine delay....................... - current 194ps Ch1 Control2 fine delay....................... - current 110ps Ch1 Control3 fine delay....................... - current 96ps Ch1 Command fine delay........................ - current 194ps Ch2 Clock Crossing Setting.................... - Auto DIMM 3 Clock fine delay....................... - current 1924ps DIMM 4 Clock fine delay....................... - current 1882ps Ch2 Control0 fine delay....................... - current 152ps Ch2 Control1 fine delay....................... - current 152ps Ch2 Control2 fine delay....................... - current 70ps Ch2 Control3 fine delay....................... - current 56ps Ch2 Command fine delay........................ - current 152ps Ch1Ch2 Common Clock Setting................... - Auto Ch1 RDCAS GNT-Chip Delay...................... - Auto Ch1 WRCAS GNT-Chip Delay...................... - Auto Ch1 Command to CS Delay....................... - Auto Ch2 RDCAS GNT-Chip Delay...................... - Auto Ch2 WRCAS GNT-Chip Delay...................... - Auto Ch2 Command to CS Delay....................... - Auto Read Delay Phase Adjust Ch1 Read delay phase (4~0) 10- 10- 10- 10- 10 Channel 1 Phase 0 Pull-In..................... - Auto Channel 1 Phase 1 Pull-In..................... - Auto Channel 1 Phase 2 Pull-In..................... - Auto Channel 1 Phase 3 Pull-In..................... - Auto Channel 1 Phase 4 Pull-In..................... - Auto Ch2 Read delay phase (4~0) 10- 10- 10- 10- 10 Channel 2 Phase 0 Pull-In..................... - Auto Channel 2 Phase 1 Pull-In..................... - Auto Channel 2 Phase 2 Pull-In..................... - Auto Channel 2 Phase 3 Pull-In..................... - Auto Channel 2 Phase 4 Pull-In..................... - Auto Voltage Setting CPU VID Control............................... - Auto 1.245 CPU Special Add Limit......................... - Disabled CPU Special Add............................... - 123.85% DRAM Voltage Control.......................... - 2.03v SB Core/CPU PLL Voltage....................... - 1.55V NB Core Voltage............................... - 1.408v CPU VTT Voltage............................... - 1.2v Vcore Droop Control........................... - Enabled Clockgen Voltage Control...................... - 3.6V CPU GTL 0 REF Volt............................ - 0.6175 CPU GTL 2 Ref Volt............................ - 0.6175 CPU GTL 1 Ref Volt............................ - 0.6175 CPU GTL 3 REF Volt............................ - 0.6175 NB GTL 0 Ref Volt............................ - 0.6175 NB GTL 1 Ref Volt............................ - 0.6175 FSB Vref...................................... - Auto [/color] ========== Orthos: 3dMark2001: 3dMark2003: 3dMark 2005: 3dMark 2006: ========== short description: 563x8.5 @ 4791Mhz, Mach2 GT cooling Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now