JOILNUVEN
Members-
Posts
45 -
Joined
-
Last visited
JOILNUVEN's Achievements
Newbie (1/14)
-
New Install - So far so good!
JOILNUVEN replied to luckybaer's topic in Processors, Motherboards and Memory
very good system... :nod: -
Bios Rom Checksum Error!
JOILNUVEN replied to Theophany's topic in Processors, Motherboards and Memory
First, i advise you: 1) post your full configuration 2) clear cmos for a few minutes...reboot, load optimized default... -
you have a very good pair of tccd try to modify this: Row cycle time (TRC)= 7(9) Row refresh cycle time (TRFC)= 14(15) Read preamble time= 5ns Idlecycle limit= 16 Dynamic counter= Enable
-
4v NF4 Jumper Worrying You? Try This Trick!
JOILNUVEN replied to AndyOCZ's topic in Cases, Power Supplies and Modding
good method!!!...but it work only at idle mode!!!... As soon as the pc is load the vdimm go down (in range 0,1-0,2v ...and the system is unstable.... the jp17 jumper give a great stability on vdimm (0,00v difference in idle and load!!! :nod: )... I put a 92x92 fan on jp17 area (about 30-40cmf)...and go fast,cold and very stable with 3,5v on my utt/bh5 -
DFI NF4 Ultra-D smoking&burning
JOILNUVEN replied to Primoz78's topic in Processors, Motherboards and Memory
yes...!!! dfi MUST give a reason about your problem!! -
DFI NF4 Ultra-D smoking&burning
JOILNUVEN replied to Primoz78's topic in Processors, Motherboards and Memory
I'm very sorry for your dead mb .. For the next mb use a great psu (for ex. tagan nforce-u22 series)...and use all precautions posted in this forum ... good luck -
DFI NF4 Ultra-D smoking&burning
JOILNUVEN replied to Primoz78's topic in Processors, Motherboards and Memory
ok friend!... measure your rails with digital multimeter....and we wait your answer tomorrow... bye -
DFI NF4 Ultra-D smoking&burning
JOILNUVEN replied to Primoz78's topic in Processors, Motherboards and Memory
your psu is not too good... your rails are too low!!!...3,22v on 3,3...4,88v on 5v... have you connect the 24pin + 4pin power?... I advise you to use a good psu (tagan nforce u22 series are very good)... I think psu is a probable cause of smoke!!!... -
DFI NF4 Ultra-D smoking&burning
JOILNUVEN replied to Primoz78's topic in Processors, Motherboards and Memory
mhh...ok!...so you use the jumper jp17 on your mb.... ...wath are your temperature with prime 95? (cpu, pwic, chipset)...and the other voltages ?(ldt, chipset,12v, 5v, 3,3v, ...) I use 2 nf4 ultra-d: one with tccd (2,7v) and the other with utt/bh5 (3,5v)....with utt/bh5 I use the jp17...so i put extra cooling (92mm fan) on power area near the jp17.... both mb works fine -
DFI NF4 Ultra-D smoking&burning
JOILNUVEN replied to Primoz78's topic in Processors, Motherboards and Memory
you set vdimm at 3,3v with your tccd? :eek:...or you use the 3,3v rail for your ram? :confused: -
Logitech X530 No front right sound
JOILNUVEN replied to importpsycho's topic in Processors, Motherboards and Memory
you must use realtek driver (and no nvidia audio drivers) http://w3serv.realtek.com.tw/downloads/dla...8&Software=True -
Bios 824 gone from list?
JOILNUVEN replied to mguggen's topic in Processors, Motherboards and Memory
i can only advise you to use stock bios (602) for optimal performance/stability nf3 ultra-d is a great mobo (i think the best 939 agp)....but there isn't a great bios -
Memory recommendations for NF3 250Gb (754)
JOILNUVEN replied to Technique's topic in OCC Market Place
there isn't dual channel mode on every socket 754 board.... because cpu A64 socket 754 don't support it