Braegnok Posted June 13, 2015 Posted June 13, 2015 (edited) slowly inch our way up with settings from default to 4.0 then 4.1,.. testing 30 min after each increase,.. monitoring max core temps during test. Edited June 13, 2015 by Braegnok Share this post Link to post Share on other sites More sharing options...
lolita1023 Posted June 13, 2015 Posted June 13, 2015 (edited) slowly inch our way up with settings from default to 4.0 then 4.1,.. testing 30 min after each increase,.. monitoring max core temps during test. Sweet ! So heres the temps of blend after 30 min : http://gyazo.com/87e67a4d40cafb77f18acc00696c036f I have now set settings as shown below for 4.0 Ring ratio : 35 Cpu multi : 40 Cpu freq : 4000 Cpu voltage : 1.080 Cpu ring voltage :1.050v System agent voltage 1.088v (+.180) I/0 Analog voltage 1.012v I/O Digital voltage : Auto I have now started the test at 4.0 , i will report in 30 min if no issues before that Ok so heres the temps after 30 min at 4.0: http://gyazo.com/f44f20808a3a6e3a1c087c04f8e398d3 What do you think so far ? Ok so now at 4.1 ,settings as shown below: Ring ratio : 37 Cpu multi : 41 Cpu freq : 4100 Cpu voltage : 1.090 Cpu ring voltage :1.056v System agent voltage 1.088v (+.210) I/0 Analog voltage 1.014v I/O Digital voltage : Auto I have now started the test at 4.1 , i will report in 30 min if no issues before that Edited June 13, 2015 by lolita1023 Share this post Link to post Share on other sites More sharing options...
Braegnok Posted June 13, 2015 Posted June 13, 2015 Temps look vary nice,.. that was something I was concerned about,.. all cores look within a few degrees of each other means your block is installed correctly and doing it's job,.. Share this post Link to post Share on other sites More sharing options...
lolita1023 Posted June 13, 2015 Posted June 13, 2015 (edited) Temps look vary nice,.. that was something I was concerned about,.. all cores look within a few degrees of each other means your block is installed correctly and doing it's job,.. Whats the max temp i should start worrying ? Cause the more we go , the more temps increases , you think i'd have to decrease any voltages or something ? I post all changes i made, you can read on the comment above Also 15 more min and i will post the result of 4.1 Ok so heres the result of 4.1 : http://gyazo.com/c9d8fb17e8f39fc606d562c7bd06760a Ok so now at 4.2 ,settings as shown below: Ring ratio : 39 Cpu multi : 42 Cpu freq : 4200 Cpu voltage : 1.1 Cpu ring voltage :1.064v System agent voltage 1.088v (+.250) I/0 Analog voltage 1.016v I/O Digital voltage : Auto First attempt to 4.2 with the above settings failed , as soon as i clicked test to start, i got a blue screen with error whea_uncorrectable_error Second attempt with voltage 1,110 failed , pc freezed after 3 mins of running test Third attempt with voltage 1,120 in progress Edited June 13, 2015 by lolita1023 Share this post Link to post Share on other sites More sharing options...
Braegnok Posted June 13, 2015 Posted June 13, 2015 (edited) max safe temp I would run would be 90c,.. at 105c the processor will show issues and throttle. Lets see how far we get on default Vcore,.. your looking good so far. I would run max 70-75c under full load for daily 24/7 usage,.. if you can stay in that temp range with under 1.2V ,.. that's the settings I would run at regardless of core speed. I would rather run at 4.2 and run fully stable with low Vcore and low temps 24/7 profile,.. than run hot at 4.4 with high Vcore 24/7. Edited June 13, 2015 by Braegnok Share this post Link to post Share on other sites More sharing options...
lolita1023 Posted June 13, 2015 Posted June 13, 2015 (edited) max safe temp I would run would be 90c,.. at 105c the processor will show issues and throttle. Lets see how far we get on default Vcore,.. your looking good so far. I would run max 70-75c under full load for daily 24/7 usage,.. if you can stay in that temp range with under 1.2V ,.. that's the settings I would run at regardless of core speed. I would rather run at 4.2 and run fully stable with low Vcore and low temps 24/7 profile,.. than run hot at 4.4 with high Vcore 24/7. I see , well lets try and see what we get at 4.4 and then decide. 11 mins left for third attempt at 1.120 for 4.2, so far so good Attempt number 3 , was successful , heres the temps after 30 mins of blend test: http://gyazo.com/ea738eff39b052b7d58e94170efcb817 Ok so now at 4.3 ,settings as shown below: Ring ratio : 39 Cpu multi : 43 Cpu freq : 4300 Cpu voltage : 1.150 Cpu ring voltage :1.118v System agent voltage 1.088v (+.250) I/0 Analog voltage 1.016v I/O Digital voltage : Auto First attempt failed , after few mins of test running pc freezed Second attempt voltage increased to 1,160 failed , blue screen after 10 mins of test running Third attempt voltage increased to 1,165 , in progress Edited June 13, 2015 by lolita1023 Share this post Link to post Share on other sites More sharing options...
Braegnok Posted June 13, 2015 Posted June 13, 2015 It's looking like your going to be in the 70-75c range at 4.3,.. which is good,.. you might make it to 4.4 under 1.2V Share this post Link to post Share on other sites More sharing options...
lolita1023 Posted June 13, 2015 Posted June 13, 2015 (edited) It's looking like your going to be in the 70-75c range at 4.3,.. which is good,.. you might make it to 4.4 under 1.2V Whats the highest safe temp i could go and be safe at 4.4 ? By safe i mean not damage cpu or something like that Third attempt at 4.3 with 1.165 failed . Blue screen after 29 minutes of test running . Fourth attempt voltage increased to 1.168 , in progress Edited June 13, 2015 by lolita1023 Share this post Link to post Share on other sites More sharing options...
Braegnok Posted June 13, 2015 Posted June 13, 2015 (edited) You can go up to 1.35V if you have the cooling,.. but we are shooting for highest core clock in 1.2V and 70-75c range for 24/7. Edited June 13, 2015 by Braegnok Share this post Link to post Share on other sites More sharing options...
lolita1023 Posted June 13, 2015 Posted June 13, 2015 (edited) You can go up to 1.35V if you have the cooling,.. but we are shooting for max 1.2V and 70-75c for 24/7 Hmm i think is gonna be higher than that , at 4.3 it has a maximum of 73c , What do you think ? Iam surprised it goes that high though , i even have a watercooling. Also what is the 'time' at RealTemp below the Minimum and maximum ? I see something like 17:22:10 Also fourth attempt at 1.168 failed at 28 mins ,Thats 1 min earlier than last attempt at 1.165.Maybe i need something in between 1,165 -1.168 or maybe i need even higher , i am not sure For fifth attempt i will try lower, 1,167 Edited June 13, 2015 by lolita1023 Share this post Link to post Share on other sites More sharing options...
Braegnok Posted June 13, 2015 Posted June 13, 2015 (edited) The time shows running min. since you last reset the time if you re-set it will go to 00:00:00,.. and the sensor test is to show that your sensors are working and not sticking or stuck,.. go ahead and run the sensor test,.. it will load prime95, watch cores heat up and cool back down,.. you have a good chip with good cooling if cores are within 7 the closer the better. Edited June 13, 2015 by Braegnok Share this post Link to post Share on other sites More sharing options...
lolita1023 Posted June 13, 2015 Posted June 13, 2015 (edited) The time shows running min. since you last reset the time if you re-set it will go to 00:00:00,.. and the sensor test is to show that your sensors are working and not sticking or stuck,.. go ahead and run the sensor test,.. it will load prime95, watch cores heat up and cool back down,.. you have a good chip with good cooling if cores are within 7 the closer the better. Ok i start the sensor test , i will post screenshot in few mins when done Ok done heres the screenshot: http://gyazo.com/bcd765c7562087e9dd09304781657000 What do you think ? Also i just start the fifth attempt at 4.3 with 1.167 this time , i am not sure whether i had to go lower or higher , fourth attempt at 1.168 failed at 28 mins ,Thats 1 min earlier than third attempt at 1.165.Maybe i need something in between 1,165 -1.168 or maybe i need even higher, i am not sure. let me know your opinion Also what do you think about the rest of the settings ? Ring ratio : 39 Cpu multi : 43 Cpu freq : 4300 Cpu ring voltage :1.176v System agent voltage 1.088v (+.250) I/0 Analog voltage 1.016v I/O Digital voltage : Auto Edited June 13, 2015 by lolita1023 Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now