Jump to content


Photo
- - - - -

[Solved] LINKSYS WRT54G- Doesn't Work


  • Please log in to reply
4 replies to this topic

#1 dragonsdontfly

dragonsdontfly

    Member

  • Members
  • PipPip
  • 369 posts
  • Gender:Male

Posted 13 March 2012 - 02:50 PM

---EDIT: Trying to simplify this post: Only 2 ports are relevant: input and output.
The following ports are the one I connect my MODEM to:
If connected to router's input; Modem detects, computer does not.
If connected to router's output; computer detects, modem does not.

Wherever the modem is connected, I connect the desktop computer to the very next port, which is either first output, or second output.


Last working condition: I had it used as a secondary router: The wireless switch for the ground floor of my house.

I cannot reset it, unplug and 90 second reset button hold still leaves it in this condition.

It DOES receive power.

---Basically, the issue is that it's "stuck" as a switch, but my new modem doesn't detect the upstream signal when the ethernet cable is plugged into the first output port.. But my PC doesn't detect downstream signal when the input is connected to the proper input port (from modem.)

I hope I didn't make this too confusing.. I'm basically just trying to get this thing out of switch mode, but I can't log into it or reset it to defaults. Anyone know how to fix this? Because I'm using my crappy backup router which automatically switches to wireless B because that's what my girlfriend's phone uses, which means I end up with an incredibly slow wireless network, instead of having the wireless G and B seperately.

Edited by dragonsdontfly, 14 March 2012 - 09:02 AM.


#2 SpeedCrazy

SpeedCrazy

    Life is one heck of a ride, so hang on tight!

  • Folding Member
  • 3817 posts
  • Gender:Male
  • Location:Between birth and death.

Posted 13 March 2012 - 02:57 PM

---EDIT: Trying to simplify this post: Only 2 ports are relevant: input and output.
The following ports are the one I connect my MODEM to:
If connected to router's input; Modem detects, computer does not.
If connected to router's output; computer detects, modem does not.

Wherever the modem is connected, I connect the desktop computer to the very next port, which is either first output, or second output.


Last working condition: I had it used as a secondary router: The wireless switch for the ground floor of my house.

I cannot reset it, unplug and 90 second reset button hold still leaves it in this condition.

It DOES receive power.

---Basically, the issue is that it's "stuck" as a switch, but my new modem doesn't detect the upstream signal when the ethernet cable is plugged into the first output port.. But my PC doesn't detect downstream signal when the input is connected to the proper input port (from modem.)

I hope I didn't make this too confusing.. I'm basically just trying to get this thing out of switch mode, but I can't log into it or reset it to defaults. Anyone know how to fix this? Because I'm using my crappy backup router which automatically switches to wireless B because that's what my girlfriend's phone uses, which means I end up with an incredibly slow wireless network, instead of having the wireless G and B seperately.


I have the same problem with two of these boxes. I set them as switches no i can't change them back. They work as switches but cannot be detected by the computer.
Fold for Team OCC


i7 930 @ 3.9 || Dual-SLI GTX 250 || ASUS P6X58D-E || 3x2GB G.Skill Pi @ 1600 || Corsair TX850w || 2x WD Caviar Black 500gb


#3 slick2500

slick2500

    mmm beer

  • Folding Member
  • 2120 posts
  • Gender:Male
  • Location:Box Elder SD

Posted 13 March 2012 - 03:25 PM

You could try this its how to recover your router if you bricked it but I think the same concept applies. http://www.dd-wrt.co...rom_a_Bad_Flash

Main Rig AMD FX 6300 @4.8Ghz Asus Sabertooth 990FX R2 Team Dark 2x4GB DDR3 1600 9-9-9-24 Dual Sapphire Radeon Vapor-X R9 270X Enermax Coenus Corsair TX850 PSU Swiftech Apogee GTX Swiftech MCR220-QP Swiftech MCP655-B

Backup Rig AMD Phenom 8650 Asus M3N78-VM 4GB DDR2 Nvidia Geforce 8200 Thermaltake 450w PSU Cheap Beige Case

 

 

WARDOZERX - My friend's I am here to warn you that should you ever stumble across a website with top notch "content" on the front page that just so happens to be sorted by a rating system, please. Please, for the love of all that is good in this world. DO NOT GO TO THE LAST PAGE! What has been seen, cannot be unseen  :whoa:

#4 dragonsdontfly

dragonsdontfly

    Member

  • Members
  • PipPip
  • 369 posts
  • Gender:Male

Posted 13 March 2012 - 05:33 PM

You could try this its how to recover your router if you bricked it but I think the same concept applies. http://www.dd-wrt.co...rom_a_Bad_Flash


Trying it now, thanks for help. I'll let you know if it works.

#5 dragonsdontfly

dragonsdontfly

    Member

  • Members
  • PipPip
  • 369 posts
  • Gender:Male

Posted 13 March 2012 - 06:00 PM

Bump:

30/30/30 didn't work.

Something I should've mentioned before: The 2nd port light is always on, even when nothing is plugged into any of the ports. 1st port now seems completely dead since 30/30/30.

I just stripped it out to use as a hiding place. Wired in the LED lights and stripped the rest. Now the front just pulls off for secret storage.

Edited by dragonsdontfly, 13 March 2012 - 06:42 PM.