Born2rade

My other two Pics.

No my Ambient temp is hotter in my room than outside. I don't know the temps inside my room. No hotter than 68F. During the summer my room gets to 80F-84F and my temps using linx gets quite close to 80C's lol. The Radiator is XSPC RX 360 and the pump i have is the swiftech MCP 3xx something lol. It's the same pump i was using with my old dual radiator. The CPU bock is XSPC Rasa.

Well i'm getting 71C's using LinX. It is about 62F outside here in Florida. Vcore @ 1.31 @ 4Ghz

Nah it's fine now. My Ram sticks were not in all the way for some weird reason lol. I must of bumped into them a few times. Everything is working great now.

Finally, Here are the pics of my PC with my new LC Setup.

I Reinstalled my LC, The PC was working just fine before and now when i go to turn it on, it will not go into POST. I do have a slight leak but it is harmless because it is just dripping onto part of the case, there are no leaks anywhere else. I'm quite confused atm....

It will be a week or so before i get the LC pics up but i can take a picture of my PC with the Megahalems in it 2morro . Btw my tubes are are not squirting anymore

oh haha guys, you are all funny . My Comp is ok i think atm. I'm going to buy Barbs and i just bought Really good clamps. Was going to go with 1/16th tubing with 1/2 barbs. not sure which barbs to get atm.... Going with tygon tubing i guess. Well i will show you guys pics when i finished the repairs lol.

When i got back from work yesterday i turned on the computer and it booted to windows fine. I replaced the tube which was a way tighter fit and i thought it wouldnt popout again but behold it poped out once again. No water leaked, temps went to 100C's+ on realtemp and the comp froze and i was able to shut it off right away. I"m going to keep it off until i find a perminant fix so that tube will not popout. I have to find a specific degree angle fittings so the tube will be straight and not so forced. The processor should be ok... i hope. This is what happend the first time, the second time was the leak spray.

It is prob too late I did turn it on twice. First was when windows would not show. Second was when I reset cmos and then didn't hear any post beeps after that I unplugged it and is now left alone. Boy I made huge mistake.

Well Today is my Birthday and well behold my tube came out and starting squirting out everywhere. i dryed everything, not much water got into the PC but i guess it did because it won't go into post now. The PC starts up, Everything lights up fine and seems to be running. THe PC did post fine at first but my desktop wouldnt show up, so than i tried resetting CMOS after i did that now it won't POST. Any Help?

ok thanks. It seems to be an intake fan.

I really want the PSU to be facing the correct way, are there any extentions or something? I have the Haf 932 and if you try to snake the wire going to the other side of the case, it will not reach the Motherboard connection....

Haha i just noticed something. The reason why the fan was facing downwards like that is because if the PSU is facing the way it is supposed to be the cables will not reach... the Motherboard, ha.... wow.

I just noticed something which i never even realized and i may feel quite stupid and retarded in a little bit. The power supply, when installed into your comp, the fan on the PSU should be facing UP, correct? Because mine was facing Downwards which makes no sense at all, I have HAF 932 Case, PSU On Bottom. As i did not build my computer, Digital Storm built mine. If i built this computer myself i would of had the Fan facing upwards so it would intake the air, instead it is intaking basically no air because it is blocked by the floor...