Jump to content

panjang110

Members
  • Posts

    274
  • Joined

  • Last visited

About panjang110

  • Birthday 11/27/1985

Profile Information

  • Gender
    Male
  • Location
    Malaysia

panjang110's Achievements

Newbie

Newbie (1/14)

  1. hi everyone, it been a while since i've posted anything here i'm a total noob when it comes to networking so help me please a few weeks ago I noticed my internet speed is slower than normal but I didn't care much since i'm busy at work. so yesterday when I was configuring my router I noticed multiple unknown device in the ip pool. I've tried putting those unknown device to deny association in my mac address filtering and reboot my router but they still keep showing up(with the same mac address that i put on the deny list ). what bother me is my password is 64 hex character how the hell did they even break through that???? so today I've change my ssid name and password again with a new 64 hex character but after an hour or so the device is in again this is really frustrating.. I've disable WPS and use WPA2-psk with AES only, right now the only thing i can do is set the max ip count to 4 which is the total device i got at home so they cant get in... any advice to secure my wifi? i really don't want to set my ip count each time i add or remove a new device.
  2. "HX-360XC is an extra thick (54mm, 2.1in) copper core radiator with a fin density of 30 FPI (fins per inch)" the rad is suitable if you're going to couple it with some high speed 38mm fan, if you're going to use the corsair sp fans i suggest running it in push-pull config
  3. nice, but i think sfx psu will look odd in my tower case
  4. hei guys,my old enermax psu is dead and i'm looking for a replacement so i need some fresh input. i'm looking for a modular psu within 500-600 watt capacity and i already got some on my list but maybe you guys can convince me with something else 1. seasonic g-550 2. seasonic m12 ii evo 520 3. cooler master silent pro gold 550 4. antec hcg 620
  5. the phone is charged on a docking station so i won't be able to put it on any surface, i have tried a normal usb charger but the charging speed is quite slow. maybe this has something to do with docking station, the station is powered by a 12v 3amp brick which is way higher than our typical micro usb charger
  6. hi guy, i just got my self a new droid and when i charge the phone it gets really hot, do i need active cooling? i know battery doesn't last long if it's hot but is it normal for smartphones? i've been using my se satio since 2010 so i really don't know what to expect. the phone is imported fujitsu arrows a 301f , the reason i bought this phone because of the fast charging advertised on the web which is quite true but they forgot to tell me about the heat
  7. unlocking a phenom rarely cause instabilty it will either crash at boot screen if the extra core is not useable or it will work. i bought a lot of phenom x 2 back in the old days and most of them will unlock to quad but some just unlock to triple. i use it for computers in a cafe running 24/7 . about stabilty issue i got one chip that need to be locked down to triple after 3 years of usage ( maybe amd did lock the core for a good reason) since you say the speed of the phenom x2 speed is 3.0 then it's the multiplier locked version (545) i wouldn't even bother overclocking it since you need a really good board to acheive high overclock.
  8. better spend that $800 on a new system+gpu, 9800gt is around 5 years old so unless you want to play old games at 120hz it's better to upgrade your gpu first.
  9. out of the three you mentioned i'll pick the eizo if you got the cash and enough gpu power to fully utilize it... if you got $800 to spend you should also look at this http://www.newegg.com/Product/Product.aspx?Item=9SIA2RY1DK9756
  10. i really want to avoid using fan controller since my one and only odd bay is occupied by my hdd,ssd and water/ambient temp display but isn't the delta fan have enough static pressure already? i couldn't find any datasheet on delta website but the nearest spec i can find is from sidewinder for EFB1212VH( VH is one step higher from HH designation) Specifications: 120x120x25mm, 102.06 CFM @ 3300 RPM, 45.5 dBA, 4.80 watts, 0.40 amps, Maximum Air Pressure 6.94 mm H
  11. last week i replace my delta fan(EFB1212HH 3000RPM) with CM jetflo120 so i can set custom fan profile with speedfan cause my wife is annoyed with the delta fan sound. i figure that i will not get too much performance drop since i've been reading good reviews on the fan especially on rad but after a week of usage i'm totally not happy. sound vs performance compared to the delta is mediocre, i've been running my delta with 7v adapter and the sound is about the same as 80% pwm on the jetflo but i'm getting higher temp and my water temp raised almost 20c above ambient after a few loop of unigine. with the delta fan the max water temp barely break 15c above ambient. here is my loop sequence pump/res=>gpu block=>cpu block=>rad=>pump/res(water temp probe on the res) cpu 3570k gpu 7970 pump-ek dcp 4.0 gpu block-heatkiller 79x0 cpu block-xspc raystorm rad- black ice gt stealth 240 5/16ID tubing on 3/8 barb + 2x90 degree adapter now i know cpu+gpu on a 240 rad is asking too much but before changing the fan i have great temps, the cpu is oc'ed per core to 4.1 on single 4.0 on dual and 3.9 on triple and quad so i don't think this will create too much heat and the card is running stock voltage 1.05v@1050/1500. after fooling around with speedfan setting i found out that 2 of my 3pin fan header allows vr control for non pwm fan (i should have downloaded speed fan first before buying the fan, silly me ) and now i can set custom fan profile for the delta fan. so right now what do you guys think i should do with the extra pair of fan? sell it off or mount it as pull?
  12. i don't own a 24' 144hz but i do own a 27' 120hz and at first i think 120-144hz monitor is overrated but after using it for months going back to 60hz gives me a headache but if i was given a choice between a 144hz screen and 21:9 i will definitely choose the latter cause i like the extra pixel without stressing the gpu too much. gaming is even better since your fov is wider. i really don't understand why everyone is hyped up over 4K hd when 21:9 is so much better for gaming and even for movies. EDIT* have you looked at LG 25UM65? it should give you better ppi count vs 29'
  13. I use the vice and hammer (with wood block), but it's not brute force. It's a gentle tap or two. So far I've delidded eight 3570K's, two 3770K's, and a 4670K with no failure rates. I use Coollaboratory Liquid Ultra for the die and IHS, and Noctua NH-1 for the TIM with the heatsink. does it have to be a wood block? can i use something else say a rubber block? i've been looking around for a guide but all of them use wood block... i couldn't find any wood block that is soft enough like pine( i live in the tropics, so soft wood is a rare comodity here ) maybe you can post a guide here for all of us with ivy/haswell chip
  14. it's your call i'm just giving some other choice since you say space is priority... but if 350d size is fine with you then go for it, i really like the 350d btw it's just that i'm used to small case ( SG09 before this N200) and 350d doesn't fit my size preference hehehe
×
×
  • Create New...