Jump to content

asudi

Members
  • Posts

    2
  • Joined

  • Last visited

About asudi

  • Birthday 11/16/1981

Gaming

  • Xfire
    asudi31
  • Steam
    asudi31
  • GamerDNA
    asudi31

Profile Information

  • Gender
    Male

asudi's Achievements

Newbie

Newbie (1/14)

  1. hello everyone so i am noob to ocing compared to most. i have messed with the oc and i just cant get it stable for gaming. desktop will run forever. i also would like to go above 3.2 would like it back around 3.8 also the cpu is on a water loop. swiftech kit 1/2in lines duel rad 655 pump. please help below r all my current settings its semi stable Motherboard: Model:Gigabyte GA-EP45T-UD3P Rev#: 1.0 Bios Version:f8c Gigabyte GA-EP45T-UD3P Cpu: Intel Q9650 Ram: G Skill F3-12800CL9-2GBNQ 4gb total ddr3 1600 Power Supply Unit: Corsair pro ax1200 note: replace all ?? with the value displayed in your bios. ----> Replace "Auto" with manually set values. MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster -------------- : [Auto] CPU Clock Ratio ---------------------- : [7] Fine CPU Clock Ratio ----------------- : [0.5] <-- ignore if not available CPU Frequency ---------------------: 3.0ghz <-- this is set by your bios Clock Chip Control Standard Clock Control CPU Host Clock Control --------------- : [Enabled] CPU Host Frequency (Mhz) --------------: [400] PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto C.I.A.2 ------------------------------ : [Disabled] Advanced Clock Control ------- [Press Enter] CPU Clock Drive ---------------------- : [800] PCI Express Clock Drive -------------- : [900] CPU Clock Skew (ps) ------------------ : [0ps] MCH Clock Skew (ps) ------------------ : [0ps] DRAM Performance Control Performance Enhance ------------------- : [standard] <--- set to STANDARD when overclocking Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled (G)MCH Frequency Latch ---------------- : [200] System Memory Multiplier -------------- : [4.00c] <-- this is the setting that you are using Memory Frequency (Mhz) ---------------- : [1600] DRAM Timing Selectable ---------------- : [manual] <-- set to MANUAL for overclocking Standard Timing Control CAS Latency Time -------- 9 ---------- : [9] tRCD -------------------- 9 ---------- : [9] tRP --------------------- 9 ---------- : [9] tRAS -------------------- 24 --------- : [25] Advanced Timing Control tRRD ------------------- ?? ---------- : [5] tWTR ------------------- ?? ---------- : [6] tWR --------------------- ?? ---------- :[12] all memory setting i got from the xmp profile. putting xmp on didnt work but putting them tRFC ------------------- ?? ---------- : [88] in manualy helped. also i lowered the voltage to 1.70 from the what xmp profile had it at 1.92 tRTP ------------------- ?? ---------- : [6] in windows i thought this was just a little high for ddr3 Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK Driving Strength Profiles Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking Channel A Static tRead Value --------------------- : [Auto] tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO tRD Phase1 Adjustment ------------------ : [Auto] tRD Phase2 Adjustment ------------------ : [Auto] tRD Phase3 Adjustment ------------------ : [Auto] Trd2rd(Different Rank) ----------------- : [Auto] Twr2wr(Different Rank) ----------------- : [Auto] Twr2rd(Different Rank) ----------------- : [Auto] Trd2wr(Same/Diff Rank) ----------------- : [Auto] Dimm1 Clock Skew Control --------------- : [Auto] ps Dimm2 Clock Skew Control --------------- : [Auto] ps Channel B Static tRead Value --------------------- : [Auto] tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO tRD Phase1 Adjustment ------------------ : [Auto] tRD Phase2 Adjustment ------------------ : [Auto] tRD Phase3 Adjustment ------------------ : [Auto] Trd2rd(Different Rank) ----------------- : [Auto] Twr2wr(Different Rank) ----------------- : [Auto] Twr2rd(Different Rank) ----------------- : [Auto] Trd2wr(Same/Diff Rank) ----------------- : [Auto] Dimm1 Clock Skew Control --------------- : [Auto] ps Dimm2 Clock Skew Control --------------- : [Auto] ps Motherboard Voltage Control CPU Voltage Types------------ Normal -------- Current ----- Load-Line Calibration ----------------- : [Enabled] CPU Vcore --------------- 1.175 ---- : [1.35] CPU Termination --------- 1.2 ----- : [Auto] CPU PLL ----------------- 1.5 ----- : [Auto] CPU Reference ----------- 0.76 ----- : [Auto] CPU Reference2 ---------- ?.???V* ----- : [Auto] <---- does not exist on this mobo MCH/ICH MCH Core ---------------- 1.1 ------- : [1.36] MCH Reference ----------- 0.76 ------- : [Auto] MCH/DRAM Ref ------------ 0.75 ------ : [Auto] ICH I/O ----------------- 1.5 ------- : [Auto] ICH Core ---------------- 1.1 ------- : [Auto] DRAM DRAM Voltage ------------ 1.50 ------- : [1.70] DRAM Termination -------- 0.75 ------- : [Auto] Channel A Reference ----- 0.75 ------- : [Auto] Channel B Reference ----- 0.75 ------- : [Auto] Advanced Settings Limit CPUID Max. to 3 ------------------ : [Disabled] No-Execute Memory Protect -------------- : [Enabled] CPU Enhanced Halt (C1E) ---------------- : [Disabled] C2/C2E State Support ------------------- : [Disabled] x C4/C4E State Support ----------------- : [Disabled] CPU Thermal Monitor 2 (TM2) ------------ : [Enabled] CPU EIST Function --------------------- : [Disabled] Virtualization Technology -------------- : [Disabled] Integrated Peripherals Legacy USB Storage Detect ------------- : [Disabled]
  2. hello everyone first post. hands shaking lol so i would love to post some results. my problem is i cant get my system stable for nothing. i feel the problem is with my memory but i really dont know enough about overclocking to dial it in. was wondering if anyone had any advise. also should i post it here. i do have a mobo template which i have filled out.
×
×
  • Create New...